Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



POWER WINDOW CONTROL SYSTEM DESCRIPTION
  1. The power window control system controls the power window UP/DOWN function by using regulator motors. This system is mainly controlled by the master switch built into the driver's door and regulator switches built into passenger's door. Pressing any of these regulator switches or the driver side door window switch mounted on the master switch transmits an UP/DOWN signal to the regulator motor for the corresponding power window, which then operates the power window UP/DOWN. Pressing any switch for the power windows except the driver's power window mounted on the master switch transmits a remote UP/DOWN signal to the front passenger power window switch via the direct line.

  2. The power window control system has the following functions:

    Function
    Outline
    Manual up-and-down function
    Function that causes window to go up while power window switch is being pulled halfway up and to go down while pushed halfway down. Window stops as soon as the switch is released.
    Jam protection function
    Function that automatically stops power window and moves it downward if a foreign object gets jammed in door window during auto-up operation.
    Remote control function
    Function that allows power window master switch to control MANUAL up-and-down operation of front passenger door window.
    Key-off operation function
    Function that makes it possible to operate power window for approx. 45 seconds after ignition switch is turned to ACC or LOCK position, if either front door is not opened.
    Diagnosis
    Function that allows the power window switch to make a diagnosis for failed section when power window switch detects a malfunction in power window system. Power window switch light comes on or blinks to inform driver.
    Fail-safe
    A fail-safe function to disable a part of power window functions if pulse sensor in power window motor has a malfunction:
    1. Driver door auto up-and-down function is disabled.
    2. Manual operation is possible by each power window switch.


CHECK WINDOW LOCK SWITCH
B066761
  1. Check that the passenger side power window and rear power window operation is disabled when the window lock switch of the power window master switch is pressed.

  2. Check that the passenger side power window and rear power windows can be operated when the window lock switch is pressed again.


CHECK MANUAL UP/DOWN FUNCTION
  1. Check that the driver side power window operates as follows:

    Standard:

    Condition
    Master Switch
    Switch Operation
    Power Window
    Ignition switch ON
    Driver side
    Pulled halfway up
    UP (Closed)
    Pulled halfway down
    DOWN (Open)

  2. Check that the power windows except the driver side power window operate as follows:

    Standard:

    Condition
    Master Switch
    Switch Operation
    Power Window
    1. Ignition switch ON
    2. Window lock switch OFF
    Passenger side
    Pulled halfway up
    UP (Closed)
    Pulled halfway down
    DOWN (Open)


CHECK AUTO UP/DOWN FUNCTION
  1. Check that the driver side power window operates as follows:
    Check that the driver side power window operates as follows:

    Standard:

    Condition
    Master Switch
    Switch Operation
    Power Window
    Ignition switch ON
    Driver side
    Pulled halfway up
    UP (Closed)
    Pulled halfway down
    DOWN (Open)


CHECK REMOTE MANUAL UP/DOWN FUNCTION
  1. Check that the power windows except the driver side power window operate as follows:

    Standard:

    Condition
    Master Switch
    Switch Operation
    Power Window
    1. Ignition switch ON
    2. Window lock switch OFF
    Passenger side
    Pulled halfway up
    UP (Closed)
    Pulled halfway down
    DOWN (Open)


MANUAL UP/DOWN FUNCTION USING DRIVER SIDE DOOR LOCK KEY CYLINDER
  1. Check that all power windows and sliding roof (standard type only) operate as follows, when the key is inserted into the driver side door lock key cylinder:

    Standard:

    Condition
    Key Operation
    Position/Operation
    No key in ignition key cylinder
    Turned left (LOCK) for more than 1.5 sec.
    Driver and passenger side power windows/UP


CHECK MANUAL DOWN FUNCTION USING TRANSMITTER
  1. Check that all power windows operate as follows when operating the transmitter:


    Condition
    Transmitter Operation
    Position/Operation
    1. No key in ignition key cylinder
    2. Any door unlocked
    UNLOCK switch pressed for more than 1.5 sec.
    Driver and passenger side power windows/ DOWN

    HINT:
    For a sign for starting operation, the wireless door lock buzzer sounds once (answer-back).


CHECK POWER WINDOW OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
  1. When both of the following conditions are fulfilled, check that the power windows can be operated even after the ignition switch is turned off.

    1. Within 45 seconds after the ignition switch is turned off.

    2. The front doors are closed.


CHECK JAM PROTECTION FUNCTION
B051853E01

HINT:
The jam protection function prevents any part of your body from getting caught by accident between the door frame and the door glass during power window operation.

NOTICE:
If the power window motor has just been reset, raise and lower the door glass several times using MANUAL function before performing the check.

  1. Check that the door glass goes down by approx. 50 mm (1.97 in.) right when something gets caught between the door frame and door glass during power window operation. However, when the opening between the door frame and the door glass is less than 200 mm (7.87 in.), the door glass continues to go down and does not stop until an opening of 200 mm (7.87 in.) is achieved. Operative conditions:

    1. AUTO UP
    2. AUTO UP function after the ignition switch is turned off
    3. MANUAL UP function after the ignition switch is turned off
    4. MANUAL UP function using the driver side door lock key cylinder