ENGINE OIL COOLER > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1) |
| 3. DRAIN ENGINE COOLANT |
Remove the radiator cap.
Loosen the radiator drain cock plug and a cylinder block drain cock plug. Then drain the coolant.

| 4. REMOVE BATTERY SERVICE HOLE COVER |
| 5. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type) |
| 6. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type) |
| 7. REMOVE FRONT DOOR SCUFF PLATE RH |
| 8. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY |
Roll up the carpet, and remove the engine service hole sub cover assembly.
| 9. REMOVE FAN AND GENERATOR V BELT |
![]() |
Remove the drive belt by rotating the tensioner pulley in clockwise direction to loosen its tension with the pulley set bolt of the tensioner.
| 10. REMOVE TIMING BELT NO.1 COVER |
Remove the wire harness clamp.
![]() |
Remove the 6 bolts and timing belt cover No.1.
| 11. REMOVE TIMING BELT |
![]() |
Turn the crankshaft in the clockwise direction and align the timing marks as shown in the illustration.
![]() |
Uniformly loosen the 2 bolts, and remove the chain tensioner assembly No.1.
Remove the timing belt.
| 12. SEPARATE VANE PUMP OIL RESERVOIR ASSEMBLY |
![]() |
Remove the 2 bolts. Separate the vane pump oil reservoir assembly.
| 13. SEPARATE OIL RETURN HOSE (w/ Intercooler) |
![]() |
Loosen the clip.
Disconnect the oil return hose from the intake manifold.
| 14. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve) |
![]() |
Disconnect the fuel pressure sensor connector.
![]() |
Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.
Remove the 2 gaskets.
| 15. REMOVE AIR HOSE NO.4 |
![]() |
Loosen the 2 clamps.
Remove the air hose No.4.
| 16. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
![]() |
Disconnect the 2 throttle body connectors.
![]() |
Remove the 2 bolts, 2 nuts, and the diesel throttle body assembly.
Remove the gasket from intake air connector.
| 17. REMOVE ENGINE SERVICE HOLE COVER NO.2 |
![]() |
Roll up the carpet.
Remove the 3 bolts and the engine service hole cover No.2.
| 18. REMOVE INTAKE AIR CONNECTOR (w/o EGR Valve) |
![]() |
Remove the bolt, and separate the manifold stay.
Disconnect the vacuum hose from intake air connector.
![]() |
Remove the bolt, 2 nuts and the intake air connector assembly.
Remove the 2 gaskets and intake air connector No.2 from the intake air connector.
| 19. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve) |
Remove the vacuum regulating valve.
![]() |
Remove the 2 vacuum hoses and the vacuum regulating valve connector.
Remove the 2 bolts and the vacuum regulating valve.
Remove the EGR valve assembly with the sensor.
![]() |
Remove the bolt, and separate the manifold stay.
Disconnect the vacuum hose from the intake air connector.
![]() |
Disconnect the intake air temperature sensor connector.
Disconnect the EGR valve position sensor connector.
![]() |
Remove the bolt, 2 nuts and the intake air connector assembly.
Remove the 2 gaskets and EGR valve assembly from the intake air connector.
| 20. REMOVE OIL LEVEL GAUGE GUIDE |
Remove the oil level gauge.
Remove the bolt and oil level gauge guide.
| 21. REMOVE INJECTION PIPE SUB-ASSEMBLY |
Remove the injection pipe.
![]() |
Remove the 2 nuts and injection pipe clamp No.3.
![]() |
Using SST, remove the 4 injection pipes.
| 22. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
Using SST, remove the fuel inlet pipe sub-assembly.
| 23. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY NO.2 |
![]() |
Disconnect 3 fuel hoses from nozzle leakage pipe assembly No.2.
![]() |
Remove the union bolt from nozzle leakage pipe No.2.
![]() |
Remove the 2 bolts and nozzle leakage pipe No.2.
Remove the gasket from nozzle leakage pipe No.2.
| 24. REMOVE INTAKE MANIFOLD |
Remove the bolt, nut, and the manifold stay.
Remove the bolt, and disconnect the ground cable.
![]() |
Remove the 4 bolts, 2 nuts, and intake manifold.
Remove the gasket from the cylinder head.
| 25. REMOVE OIL FILTER SUB-ASSEMBLY |
![]() |
Using SST, remove the oil filter.
| 26. REMOVE COMMON RAIL ASSEMBLY |
Disconnect the fuel pressure sensor connector from the common rail assembly.
Disconnect the fuel hose from the fuel pressure limiter.
![]() |
Remove the 2 bolts and common rail assembly.
| 27. REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY |
![]() |
Remove the 4 bolts.
Remove the camshaft timing pulley flange No.2 and pump drive shaft pulley.
![]() |
Using SST, remove the supply pump gear set nut and O-ring while holding the crankshaft pulley.
![]() |
Disconnect the 2 fuel hoses.
Disconnect the 2 connectors and wire harness.
Loosen the 2 nuts as shown in the illustration.
![]() |
Using SST, disengage the supply pump from the supply pump gear.
Remove the 2 nuts and supply pump from the engine.
Remove the O-ring from the supply pump.
Remove the pulley key from the supply pump.
| 28. REMOVE OIL COOLER COVER SUB-ASSEMBLY (w/o EGR Valve) |
![]() |
Disconnect the oil pressure switch connector.
Disconnect the oil filter drain hoses.
![]() |
Remove the 2 nuts, 13 bolts, oil cooler cover, and gasket.
| 29. REMOVE OIL COOLER COVER SUB-ASSEMBLY (w/ EGR Valve) |
![]() |
Disconnect the oil pressure switch connector.
Disconnect the oil filter drain hoses.
Remove the 2 nuts and the vacuum transmitting pipe No.2 from the oil cooler cover.
![]() |
Remove the 13 bolts, oil cooler cover, and gasket.
| 30. REMOVE OIL COOLER ASSEMBLY |
![]() |
Loosen the 4 nuts until they are flush with the end of the bolts.
Using a plastic hammer, uniformly tap the end of the nuts to separate the oil cooler cover and oil cooler assembly.
![]() |
Remove the 4 nuts, oil cooler assembly, and 2 gaskets from the oil cooler cover.