ANTI-LOCK BRAKE SYSTEM > TEST MODE PROCEDURE |
| TEST MODE (SIGNAL CHECK) PROCEDURE (WHEN USING SST CHECK WIRE:) |
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position and move the shift lever to the P position (Automatic Transmission) or apply the parking brake (Manual Transmission).
![]() |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch to the ON position.
![]() |
After the ABS warning light comes on for several seconds, check if one of the following ECU codes is output.
| ECU Code | Floor Type | Wheelbase |
| 1 | Standard | Standard |
| 2 | Standard | Long |
| 5 | Flat | Standard |
Check that the ABS warning light starts to blink after the ECU code is indicated. This transition shows that the Test Mode is activated.
A blinking pattern of the ABS warning light (transition from ECU code 2 to Test Mode) is shown below as an example.

![]() |
Check that the ABS warning light is blinking in the Test Mode.
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit |
Click here or Click here
|
Start the engine.
Using SST, perform the speed sensor signal check in Test Mode.
| SPEED SENSOR SIGNAL CHECK |
![]() |
Check that the ABS warning light is blinking in Test Mode.
Drive the vehicle straight forward.
Accelerate the vehicle to a speed of 28 mph (45 km/h) or higher for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| READ DTC |
![]() |
Using SST, connect terminals TC and CG of the DLC3.
Read the number of blinks of the ABS warning light.

After performing the check, disconnect the SST from terminals TS and CG, TC and CG of the DLC3 and turn the ignition switch off.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION |
| Code No. | Diagnosis | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH | Skid control rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | Skid control rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | Skid control rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | Skid control rotor |
| TEST MODE (SIGNAL CHECK) PROCEDURE (WHEN USING INTELLIGENT TESTER:) |
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position and move the shift lever to the P position (Automatic Transmission) or apply the parking brake (Manual Transmission).
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Set the intelligent tester to Test Mode (select "Signal Check").
![]() |
After the ABS warning light comes on for several seconds, check if one of the following ECU codes is output.
| ECU Code | Floor Type | Wheelbase |
| 1 | Standard | Standard |
| 2 | Standard | Long |
| 5 | Flat | Standard |
Check that the ABS warning light starts to blink after the ECU code is indicated. This transition shows that the Test Mode is activated.
A blinking pattern of the ABS warning light (transition from ECU code 2 to Test Mode) is shown below as an example.

![]() |
Check that the ABS warning light is blinking in the Test Mode.
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit |
Click here or Click here
|
Start the engine.
Using the intelligent tester, perform the speed sensor signal check in Test Mode.
| SPEED SENSOR SIGNAL CHECK |
![]() |
Check that the ABS warning light is blinking in Test Mode.
Drive the vehicle straight forward.
Accelerate the vehicle to a speed of 28 mph (45 km/h) or higher for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| READ DTC |
Read the DTC(s) by following the tester screen.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION |
| Code No. | Diagnosis | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH | Skid control rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | Skid control rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | Skid control rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | Skid control rotor |