Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/o Secondary Air Injection System)

SFI SYSTEM (w/o Secondary Air Injection System) > Variable Resistor Circuit

for Preparation Click here


DESCRIPTION

This resistor is used to change the air-fuel ratio of the air-fuel mixture.
The idle mixture is adjusted using this resistor.
Turning the idle mixture adjusting screw clockwise moves the contacts inside the resistor, raising the terminal VAF voltage. Conversely, turning the screw counterclockwise lowers the terminal VAF voltage.
When the terminal VAF voltage rises, the ECM increases the injection volume slightly, marking the air-fuel mixture a little richer.

WIRING DIAGRAM


A111678E01


INSPECTION PROCEDURE

NOTICE:
Always use a CO meter when adjusting the idle mixture. If a CO meter is not available, DO NOT ATTEMPT TO ADJUST IDLE MIXTURE.

1.CHECK CO/HC
  1. Warm up the engine to normal operating temperature.

  1. Switch all accessories OFF.

  1. Connect all vacuum lines properly.

  1. Connect the tachometer.

  1. Check ignition timing correctly.

  1. Check idle speed correctly.

  1. Check that the CO meter is properly calibrated.

  1. Race the engine at 2,500 rpm about 2 minutes.

  1. Insert a tester probe at least 40 cm (1.3 ft) into the tailpipe.

  1. Measure the concentration for 1 to 3 minutes after racing the engine to allow the concentration to stabilize.

    Idle CO concentration:
    1.0 to 2.0 %



OK
CHECK FOR PROBLEM SYMPTOMS TABLE
NG


2.ADJUST CO CONCENTRATION


    A073579E01
  1. Put the vehicle in the same condition as step 1 of this chart.

  1. Using SST, adjust the idle mixture by turning the idle mixture adjusting screw in the variable resistor.

    Result:
    Result
    Proceed to
    Concentration: 1.0 to 2.0 %
    B
    Change in CO concentration
    C
    No change in CO concentration
    A

    HINT:
    1. Always check idle speed after turning the idle mixture adjusting screw. If it is incorrect, readjust idle speed.
    2. The idle mixture adjusting screw can be turned within 180 degrees. Do not turn this screw more than the specified.

SST
09243-00020  


B
ADJUST COMPLETE

C
CHECK CO/HC
A


3.INSPECT VARIABLE RESISTOR


    A074545E01
  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    1 - 2
    3.5 to 6.5 Ω

  1. Measure the resistance according to the value(s) in the table below, when turning the idle mixture adjusting screw fully clockwise and counterclockwise using SST.

    Resistance:
    Tester Connection
    Specified Condition
    2 - 3
    Change from about 5 kΩ to 0 kΩ accordingly

SST
09243-00020  


NG
REPLACE VARIABLE RESISTOR
OK


4.CHECK ECM (VAF VOLTAGE)


    G038493E02
  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below while slowly turning the idle mixture adjusting screw first fully counterclockwise and then fully clockwise, using SST.

    Voltage:
    Tester Connection
    Specified Condition
    VAF (D1-25) - E2 (D1-28)
    Voltage changes smoothly from 0 V to about 5 V, i.e. does not suddenly jump up to 5 V down to 0 V

SST
09243-00020  


OK
REPLACE ECM
NG


5.CHECK HARNESS AND CONNECTOR (VARIABLE RESISTOR - ECM)


    A112051E02
  1. Disconnect the D31 variable resistor connector.

  1. Disconnect the D1 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (check for open):
    Tester Connection
    Specified Condition
    VC (D31-2) - VC (D1-18)
    Below 1 Ω
    VAF (D31-3) - VAF (D1-25)
    Below 1 Ω
    E2 (D31-1) - E2 (D1-28)
    Below 1 Ω

    Resistance (check for short)::
    Tester Connection
    Specified Condition
    VC (D31-2) or VC (D1-18) - Body ground
    10 kΩ or higher
    VAF (D31-3) or VAF (D1-25) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the variable resistor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM