Home › ENGINE ยท 2KD-FTV › INTAKE › INTAKE SYSTEM

INTAKE SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. INTAKE AIR PIPE
  1. Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and cylinder head.

    Condition
    Operation
    Clogged air cleaner
    Clean or replace
    Collapsed or deformed hoses
    Repair or replace
    Leakage from connections
    Check each connection and repair
    Cracks in components
    Check and replace



2. EXHAUST SYSTEM
  1. Check for leakage or clogging between the cylinder head and turbocharger inlet, and between the turbocharger outlet and exhaust pipe.

    Condition
    Operation
    Deformed components
    Repair or replace
    Foreign matter in passages
    Remove
    Leakage from components
    Repair or replace
    Cracks in components
    Check and replace



3. TURBOCHARGING PRESSURE


    A106850E01
  1. Warm up the engine.

  1. Using a 3-way connector, connect SST (turbocharger pressure gauge) to the hose between the manifold absolute pressure sensor and gas filter leading to the intake air connector.

    SST
    09992-00242  

  1. Fully depress the accelerator pedal. Measure the turbocharging pressure at maximum speed (approximately 4,600 rpm).

    Standard pressure:
    58.5 to 78.9 kPa (0.60 to 0.80 kgf/cm2, 8.5 to 11.4 psi)

    If the pressure is less than the minimum, check the intake air and exhaust systems for leakage. If there is no leakage, replace the turbocharger.
    If the pressure is above the specification, check if the actuator hose is disconnected or cracked. If it is not, check the turbocharger.



4. TURBINE SHAFT


    A099553
  1. Grasp the edge of the turbine shaft and turn it. Check that the turbine shaft turns smoothly.
    If the turbine shaft does not turn or turns with a heavy drag, replace the turbocharger.



5. INSPECT DIESEL TURBO PRESSURE SENSOR


    A113810
  1. Inspect the power source voltage.

    1. Disconnect the pressure sensor connector.

    2. Turn the ignition switch ON.

    3. Using a voltmeter, measure the voltage between terminals 3(VC) and 1(E2) of the wiring harness side connector.

      Standard voltage:
      4.5 to 5.5 V

      If the result is not as specified, inspect the wire harness or ECM.

    4. Turn the ignition switch off.

    5. Connect the pressure sensor connector.

      NOTICE:
      Clear the DTCs after inspection is completed.



    G039061E04
  1. Check the power supply.

    1. Turn the ignition switch ON.

    2. Disconnect the vacuum hose from the pressure sensor.

    3. Connect a voltmeter to terminals D3-28 (PIM) and D1-28 (E2) of the ECM connectors, and measure the output voltage under ambient atmospheric pressure.



    4. A113809E01
    5. Apply a vacuum to the pressure sensor in 13.3 kPa (100 mmHg, 3.94 in.Hg) increments until the pressure reaches 40.0 kPa (300 mmHg, 11.81 in.Hg).

    6. Measure the decrease in voltage from step (3) for each increment.

      Standard voltage:
      Applied Vacuum
      Voltage Decrease
      13.3 kPa (100 mmHg, 3.94 in.Hg)
      0.1 to 0.4 V
      26.6 kPa (199 mmHg, 7.85 in.Hg)
      0.2 to 0.6 V
      40 kPa (300 mmHg, 11.81 in.Hg)
      0.4 to 0.8 V

      If the result is not as specified, replace the diesel turbo pressure sensor.



    7. A106851E01
    8. Using SST (turbocharger pressure gauge), apply pressure to the pressure sensor in 19.6 kPa (0.20 kgf/cm2, 2.84 psi) increments until the pressure reaches 98.0 kPa (1.00 kgf/cm2, 14.2 psi).

      SST
      09992-00242  

    9. Measure the increase in voltage from step (6) for each increment.

      Standard voltage:
      Applied Pressure
      Voltage Increase
      19.6 kPa (0.20 kgf/cm2, 2.84 psi)
      0.1 to 0.4 V
      39.2 kPa (0.40 kgf/cm2, 5.69 psi)
      0.4 to 0.7 V
      58.8 kPa (0.60 kgf/cm2, 8.53 psi)
      0.7 to 1.0 V
      78.5 kPa (0.80 kgf/cm2, 11.4 psi)
      1.0 to 1.3 V
      98.0 kPa (1.00 kgf/cm2, 14.2 psi)
      1.3 to 1.6 V

      If the result is not as specified, replace the diesel turbo pressure sensor.