Home › ENGINE · 2TR-FE › IGNITION › IGNITION SYSTEM

IGNITION SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. PERFORM SPARK TEST
  1. Check for DTCs.

    NOTICE:
    If a DTC is present, perform troubleshooting procedures for that DTC.

  1. Check if sparks occur.

    1. Remove the front seat assembly. (See page )

    2. Remove the front door scuff plate RH. (See page )

    3. Remove the engine service hole sub cover sub-assembly. (See page )

    4. Remove the ignition coil.

    5. Remove the spark plug.

    6. Install the spark plug to the ignition coil and connect the ignition coil connector.

    7. Disconnect the 4 injector connectors.

    8. Ground the spark plug.

    9. Visually check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Be sure to ground the spark plug before checking.
      2. If the ignition coil has been struck or dropped, replace it.
      3. Do not crank the engine for more than 2 seconds.

  1. Spark test flowchart.

    1. Check that the wire harness side connector of the ignition coil with igniter is securely connected.

      Result:
      Result
      Proceed to
      NG
      Connect securely
      OK
      Go to next step

    2. Perform spark test on each ignition coil with igniter.

      1. Replace the ignition coil with igniter with a normal one.
      2. Perform spark test again.

      Result:
      Result
      Proceed to
      OK
      Replace ignition coil with igniter
      NG
      Go to next step

    3. Check the power supply to ignition coil with igniter.

      1. Turn the ignition switch ON.
      2. Check that there is battery voltage at the ignition coil positive (+) terminal.

      Result:
      Result
      Proceed to
      NG
      Check wiring between engine switch and ignition coil with igniter
      OK
      Go to next step

    4. Check the camshaft position sensor.

      1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      950 to 1250 Ω at 20°C (68°F)

      Result:
      Result
      Proceed to
      NG
      Replace camshaft position sensor
      OK
      Go to next step

    5. Check the of crankshaft position sensor.

      1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      1850 to 2450 Ω at 20°C (68°F)

      Result:
      Result
      Proceed to
      NG
      Replace crankshaft position sensor
      OK
      Go to next step

    6. Check IGT signal from the ECM.

      Result:
      Result
      Proceed to
      NG
      Check ECM
      OK
      Repair wiring between ignition coil and ECM

  1. Install the ignition coil.

    1. Using a 16 mm plug wrench, install the spark plug.

      Torque:
      18 N*m{ 183 kgf*cm , 13 ft.*lbf }

    2. Install the ignition coil.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    3. Install the engine service hole sub cover sub-assembly (See page ).

    4. Install the front door scuff plate RH (See page ).

    5. Install the front seat assembly (See page ).



2. CHECK SPARK PLUG (for Unleaded Gasoline Specification Vehicle)

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.



    I039522E06
  1. Check the electrode.

    1. Using a megohmmeter, measure the insulation resistance.

      Insulation resistance:
      10 MΩ or more

      HINT:
      If a megohmmeter is not available, perform the following simple inspection instead.



    B002629
  1. Alternative inspection method.

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its threads and insulator.
    If there is damage, replace the spark plug. If not, reinstall the spark plug.

    Recommended spark plug:
    Manufacture
    Product
    DENSO made
    SK20HR11
    NGK made
    ILFR6C11



    B002630E01
  1. Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.3 mm (0.051 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

    NOTICE:
    When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.



    B062019E01
  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Air pressure:
    588 kPa (6 kgf*cm2, 85 psi)

    Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.



3. CHECK SPARK PLUG (for Leaded Gasoline Specification Vehicle)


    I039522E06
  1. Check the electrode.

    1. Using a megohmmeter, measure the insulation resistance.

      Insulation resistance:
      10 MΩ or more

      HINT:
      If a megohmmeter is not available, perform the following simple inspection instead.



    G037847E01
  1. Alternative inspection method:

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its threads and insulator.
    If there is damage, replace the spark plug. If not, reinstall the spark plug.

    Recommended spark plug:
    Manufacture
    Product
    DENSO made
    K20HR-U11
    NGK made
    LFR6C-11



    G037848E01
  1. Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.3 mm (0.051 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.1 mm (0.043 in.)

    NOTICE:
    When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Never attempt to adjust the gap of a used plug.



    B062019E01
  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Air pressure:
    588 kPa (6 kgf*cm2, 85 psi)

    Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.