Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Fuel Receiver Gauge Malfunction

for Preparation Click here


WIRING DIAGRAM


E111211E01


INSPECTION PROCEDURE

1.SYSTEM CHECK

Result 
Condition
Go To Step
Fuel level warning light operates normally.
B
Any malfunction except above.
A


B
REPLACE COMBINATION METER ASSEMBLY
A


2.INSPECT COMBINATION METER ASSEMBLY


    I030899E06
  1. Disconnect the connector from the fuel sender gauge.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
FS (2) - FE (3)
Always
10 to 14 V

*1: Gasoline engine
*2: Diesel engine


NG
Go to step 5
OK


3.INSPECT FUEL SENDER GAUGE ASSEMBLY


    E111218E02
  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance 
Tester Connection
Condition
Specified Condition
h2-2 (FS) - h2-3 (FE) (*1)
Always
3.0 to 112.5 Ω
h1-2 (FS) - h1-3 (FE) (*2)
Always
3.0 to 112.5 Ω
*1: Gasoline engine
*2: Diesel engine


NG
Go to step 6
OK


4.INSPECT FUEL SENDER GAUGE ASSEMBLY


    I030899E06
  1. Short terminals 2 and 3 at the wire harness side.

  1. Turn the ignition switch ON.

    OK:
    Fuel sender gauge needle indicates F or more.

    *1: Gasoline engine
    *2: Diesel engine



OK
Go to step 6
NG


5.CHECK HARNESS AND CONNECTOR (BETWEEN COMBINATION METER AND FUEL SENDER GAUGE ASSEMBLY)
  1. Disconnect the H20 and h2 (*1)/h1 (*2) connectors.



    E109206E03
  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance 
Tester Connection
Condition
Specified Condition
H20-13 (L) - h2-2 (FS) (*1)
Always
Below 1 Ω
H20-8 (E2) - h2-3 (FE) (*1)
Always
Below 1 Ω
H20-13 (L) - h1-2 (FS) (*2)
Always
Below 1 Ω
H20-8 (E2) - h1-3 (FE) (*2)
Always
Below 1 Ω
h2-2 (FS) - Body ground (*1)
Always
10 kΩ or higher
h1-2 (FS) - Body ground (*2)
Always
10 kΩ or higher
*1: Gasoline engine
*2: Diesel engine


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY 

6.INSPECT FUEL SENDER GAUGE ASSEMBLY


    E111199E01
  1. Check that the float moves between F (top) and E (bottom) smoothly.

    OK:
    The float moves between F (top) and E (bottom) smoothly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Gasoline Engine):
    Float Level
    Specified Resistance
    F
    3.0 to 5.0 Ω
    E
    107.5 to 112.5 Ω

    Standard Resistance (Diesel Engine):
    Float Level
    Specified Resistance
    F
    3.0 to 5.0 Ω
    E
    107.5 to 112.5 Ω



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY
OK

END