DTC 19 (1) Accelerator Position Sensor Circuit Malfunction |

| DTC No. | DTC Detecting Condition | Trouble Area |
| 19(1) | Condition (a), (b), (c) or (d) continues for 2.0 seconds: (a) VPA <= 0.2 V and VPA2 <= 0.5 V (b) VPA >= 4.8 V (c) When 3.45 V >= VPA >= 0.2 V, and VPA2 >= 4.8 V (d) VPA-VPA2 <= 0.02 V |
|
| Condition (a) continues for 0.5 seconds: (a) VPA <= 0.2 V or VPA2 <= 0.5 V |
| Trouble area | Accelerator pedal position expressed as voltage | |||
| Accelerator pedal released | Accelerator pedal depressed | |||
| ACCEL POS #1 | ACCEL POS #2 | ACCEL POS #1 | ACCEL POS #2 | |
| VC circuit open | 0 - 0.2 V | 0 - 0.2 V | 0 - 0.2 V | 0 - 0.2 V |
| VPA circuit open or ground short | 0 - 0.2 V | 1.2 - 2.0 V | 0 - 0.2 V | 3.4 - 5.3 V |
| VPA2 circuit open or ground short | 0.5 - 1.1 V | 0 - 0.2 V | 2.6 - 4.5 V | 0 - 0.2 V |
| E2 circuit open | 4.5 - 5.5 V | 4.5 - 5.5 V | 4.5 - 5.5 V | 4.5 - 5.5 V |

| 1.READ VALUE OF INTELLIGENT TESTER (ACCELERATOR POSITION) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Select the item "Powertrain/Engine and ECT/Data List/Accel position" and read its value displayed on the intelligent tester.
|
| ||||
| OK | |
| 2.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 sec. or more.
Read the DTC (Click here).
| Display (DTC output) | Proceed to |
| DTC 19(1) is output again | A |
| No DTC output | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM B8 and D4 connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VCP2 (B1-1) - VC (D4-1) | Below 1 Ω |
| EPA2 (B1-2) - E2 (D4-9) | Below 1 Ω |
| VPA2 (B1-3) - VPA2 (B8-12) | Below 1 Ω |
| VCPA (B1-4) - VCPA (B8-6) | Below 1 Ω |
| EPA (B1-5) - EPA (B8-4) | Below 1 Ω |
| VPA (B1-6) - VPA (B8-5) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VCP2 (B1-1) or VC (D4-1) - Body ground | 10 kΩ or higher |
| EPA2 (B1-2) or E2 (D4-9) - Body ground | 10 kΩ or higher |
| VPA2 (B1-3) or VPA2 (B8-12) - Body ground | 10 kΩ or higher |
| VCPA (B1-4) or VCPA (B8-6) - Body ground | 10 kΩ or higher |
| EPA (B1-5) or EPA (B8-4) - Body ground | 10 kΩ or higher |
| VPA (B1-6) or VPA (B8-5) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT ECM (VC AND VCPA VOLTAGE) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VC (D4-1) - E2 (D4-9) | 4.5 to 5.5 V |
| VCPA (B8-6) - EPA (B8-4) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 5.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 6.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 sec. or more.
Read the DTC (Click here).
| Display (DTC output) | Proceed to |
| DTC 19(1) is output again | A |
| No DTC output | B |
|
| ||||
| A | ||
| ||
| 1.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM B8 and D4 connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VCP2 (B1-1) - VC (D4-1) | Below 1 Ω |
| EPA2 (B1-2) - E2 (D4-9) | Below 1 Ω |
| VPA2 (B1-3) - VPA2 (B8-12) | Below 1 Ω |
| VCPA (B1-4) - VCPA (B8-6) | Below 1 Ω |
| EPA (B1-5) - EPA (B8-4) | Below 1 Ω |
| VPA (B1-6) - VPA (B8-5) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VCP2 (B1-1) or VC (D4-1) - Body ground | 10 kΩ or higher |
| EPA2 (B1-2) or E2 (D4-9) - Body ground | 10 kΩ or higher |
| VPA2 (B1-3) or VPA2 (B8-12) - Body ground | 10 kΩ or higher |
| VCPA (B1-4) or VCPA (B8-6) - Body ground | 10 kΩ or higher |
| EPA (B1-5) or EPA (B8-4) - Body ground | 10 kΩ or higher |
| VPA (B1-6) or VPA (B8-5) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT ECM (VC AND VCPA VOLTAGE) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VC (D4-1) - E2 (D4-9) | 4.5 to 5.5 V |
| VCPA (B8-6) - EPA (B8-4) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 4.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 sec. or more.
Read the DTC (Click here).
| Display (DTC output) | Proceed to |
| DTC 19(1) is output again | A |
| No DTC output | B |
|
| ||||
| A | ||
| ||