DTC 19 (2) Accelerator Position Sensor Range / Performance Problem |

| DTC No. | DTC Detecting Condition | Trouble Area |
| 19 (2) | Either of the ECM sensor completed learning and when the electric potential difference of No. 1 and No. 2 sensors has become more than 1.2 V or less than 0.4 V. |
|
One of the following continues more than 2.0 seconds.
|
| Trouble area | Accelerator pedal position expressed as voltage | |||
| Accelerator pedal released | Accelerator pedal depressed | |||
| ACCEL POS #1 | ACCEL POS #2 | ACCEL POS #1 | ACCEL POS #2 | |
| VC circuit open | 0 - 0.2 V | 0 - 0.2 V | 0 - 0.2 V | 0 - 0.2 V |
| VPA circuit open or ground short | 0 - 0.2 V | 1.2 - 2.0 V | 0 - 0.2 V | 3.4 - 5.3 V |
| VPA2 circuit open or ground short | 0.5 - 1.1 V | 0 - 0.2 V | 2.6 - 4.5 V | 0 - 0.2 V |
| E2 circuit open | 4.5 - 5.5 V | 4.5 - 5.5 V | 4.5 - 5.5 V | 4.5 - 5.5 V |

| 1.READ VALUE OF INTELLIGENT TESTER (ACCELERATOR POSITION) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Select the item "Powertrain/Engine and ECT/Data List/Accel position" and read its value displayed on the intelligent tester.
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM B8 and D4 connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VCP2 (B1-1) - VC (D4-1) | Below 1 Ω |
| EPA2 (B1-2) - E2 (D4-9) | Below 1 Ω |
| VPA2 (B1-3) - VPA2 (B8-12) | Below 1 Ω |
| VCPA (B1-4) - VCPA (B8-6) | Below 1 Ω |
| EPA (B1-5) - EPA (B8-4) | Below 1 Ω |
| VPA (B1-6) - VPA (B8-5) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VCP2 (B1-1) or VC (D4-1) - Body ground | 10 kΩ or higher |
| EPA2 (B1-2) or E2 (D4-9) - Body ground | 10 kΩ or higher |
| VPA2 (B1-3) or VPA2 (B8-12) - Body ground | 10 kΩ or higher |
| VCPA (B1-4) or VCPA (B8-6) - Body ground | 10 kΩ or higher |
| EPA (B1-5) or EPA (B8-4) - Body ground | 10 kΩ or higher |
| VPA (B1-6) or VPA (B8-5) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 1.INSPECT ECM (VPA AND VPA2 VOLTAGE) |
![]() |
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VPA (B8-5) - EPA (B8-4) | 0.5 to 1.1 V |
| VPA2 (B8-12) - E2 (D4-9) | 1.2 to 2.0 V |
| Tester Connection | Specified Condition |
| VPA (B8-5) - EPA (B8-4) | 2.6 to 4.5 V |
| VPA2 (B8-12) - E2 (D4-9) | 3.4 to 5.3 V |
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM B8 and D4 connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VCP2 (B1-1) - VC (D4-1) | Below 1 Ω |
| EPA2 (B1-2) - E2 (D4-9) | Below 1 Ω |
| VPA2 (B1-3) - VPA2 (B8-12) | Below 1 Ω |
| VCPA (B1-4) - VCPA (B8-6) | Below 1 Ω |
| EPA (B1-5) - EPA (B8-4) | Below 1 Ω |
| VPA (B1-6) - VPA (B8-5) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VCP2 (B1-1) or VC (D4-1) - Body ground | 10 kΩ or higher |
| EPA2 (B1-2) or E2 (D4-9) - Body ground | 10 kΩ or higher |
| VPA2 (B1-3) or VPA2 (B8-12) - Body ground | 10 kΩ or higher |
| VCPA (B1-4) or VCPA (B8-6) - Body ground | 10 kΩ or higher |
| EPA (B1-5) or EPA (B8-4) - Body ground | 10 kΩ or higher |
| VPA (B1-6) or VPA (B8-5) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||