Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL

REAR DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN DIFFERENTIAL OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install the drain plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



2. REMOVE PROPELLER SHAFT ASSEMBLY (for Super Long Wheelbase)


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller with center bearing shaft assembly from the differential companion flange.



    C107214
  1. Remove the 2 bolts and center support bearing assembly No.1.

  1. Remove the propeller with center bearing shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission.

      SST
      09325-40010  

    2. Use the following SST for the manual transmission.

      SST
      09325-20010  



3. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  



4. REMOVE REAR DRIVE PINION NUT


    C111573E01
  1. Using SST and a hammer, release the staked part of the drive pinion nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of the SST with a grinder etc.
    3. Completely loosen the staked part of the nut when removing it.
    4. Do not damage the threads of the drive pinion.



    C111572E01
  1. Using SST to hold the flange, remove the drive pinion nut.

    SST
    09330-00021  



5. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C111575E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



6. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    C111571E01
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



7. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


8. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C111570E01
  1. Using SST, remove the inner race of the rear drive pinion front tapered roller bearing from the drive pinion.

    SST
    09556-22010  

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



9. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


10. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


    C093595
  1. Install a new drive pinion bearing spacer to the drive pinion.

    NOTICE:
    Be sure to face the larger inner diameter side rearward as shown in the illustration.



11. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


12. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


13. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


    C116321E01
  1. Using SST and a hammer, install a new oil seal.

    SST
    09554-22010  

    Oil seal drive in depth:
    0.55 to 1.45 mm (0.0217 to 0.0571 in.)

  1. Apply MP grease to the oil seal lip.



14. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C111575E02
  1. Using SST, install the companion flange to the drive pinion.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)
    09330-00021  

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



    C111574E01
  1. Coat the threads of a new drive pinion nut with hypoid gear oil LSD.

  1. Using SST to hold the flange, temporarily tighten the drive pinion nut.

    SST
    09330-00021  



15. INSPECT AND ADJUST DIFFERENTIAL DRIVE PINION PRELOAD


    C089308
  1. Using a torque wrench, measure the preload of the drive pinion.

    Preload (at starting):
    New bearing:
    1.05 to 1.64 N*m (11.0 to 17.0 kgf*cm, 9 to 15 in.*lbf)
    Reused bearing:
    0.56 to 0.85 N*m (6.0 to 9.0 kgf*cm, 5 to 8 in.*lbf)

  1. If the preload is less than the specified minimum value, check the preload while retightening the drive pinion nut by 5 to 10° to adjust it into the specified range.

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less

  1. If the preload is less than the specified minimum value even when the tightening torque of the drive pinion nut is greater than the specified maximum value, loosen the nut and check that the threads of the drive pinion nut and drive pinion are not stripped.

  1. If the threads are not stripped, replace the bearing spacer. Apply hypoid gear oil LSD to the threads of the drive pinion and repeat the procedure.



16. INSTALL REAR DRIVE PINION NUT


    C089310
  1. Using a chisel and hammer, stake the drive pinion nut.



17. INSTALL PROPELLER SHAFT ASSEMBLY (for Super Long Wheelbase)


    C102186E01
  1. Remove the SST from the extension housing.

  1. Install the propeller with center bearing shaft assembly in the extension housing.



    C107214
  1. Install the center support bearing assembly No.1, and temporarily tighten the 2 bolts.



    C102185E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assy with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }



    C107213E01
  1. Check that the center line of the bracket is at right angles to the shaft axial direction.



    C115777E01
  1. Adjust the center support bearing assembly No.1.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing No.1 to maintain the angles, as shown.
    2. In the same conditions, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) of each other in the vehicle's longitudinal direction with the vehicle unladen.

  1. Tighten the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



18. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)


    C102186E01
  1. Remove the SST from the extension housing.

  1. Install the propeller shaft assembly in the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.



    C102185E01
  1. Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }



19. FILL DIFFERENTIAL OIL
  1. Remove the differential filler plug and gasket.

  1. Fill with oil.

    Oil grade:
    Hypoid gear oil API GL-5 or equivalent


    Recommended oil viscosity 
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W or 80W-90

  1. Check the oil level.

  1. Install the differential filler plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    After replacing the oil, recheck the oil level after driving.



20. INSPECT AND ADJUST DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.



    D025304E04
  1. Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause trouble.
    2. After replacing oil, drive the vehicle and check the oil level.

    HINT:
    If necessary, fill the rear differential carrier with hypoid gear oil.

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }