DTC B1610/13 Front Airbag Sensor RH Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1610/13 |
|
|

| 1.CHECK DTC |
![]() |
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.
|
| ||||
| OK | |
| 3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH.
Using a service wire, connect B4-29 (+SR) and B4-27 (-SR) of connector "B".
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| A12-2 (+SR) - A12-1 (-SR) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT) |
![]() |
Disconnect the service wire from connector "B".
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| A12-2 (+SR) - A12-1 (-SR) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| A12-2 (+SR) - Body ground | Always | 1 MΩ or higher |
| A12-1 (-SR) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| A12-2 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| A12-1 (-SR) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK FRONT AIRBAG SENSOR RH |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the front airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1610/13 is output. | A |
| DTC B1615/14 is output. | B |
| DTC B1610/13 and B1615/14 are not output. | C |
|
| ||||
|
| ||||
| C | ||
| ||
| 8.CHECK ENGINE ROOM MAIN WIRE (OPEN) |
![]() |
Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| AB2-1 (+SR) - AB2-3 (-SR) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 9.CHECK ENGINE ROOM MAIN WIRE (SHORT) |
![]() |
Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| AB2-1 (+SR) - AB2-3 (-SR) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 10.CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND) |
![]() |
Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| AB2-1 (+SR) - Body ground | Always | 1 MΩ or higher |
| AB2-3 (-SR) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| AB2-1 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| AB2-3 (-SR) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||