Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1615/14    Front Airbag Sensor LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The front airbag sensor LH consists of the diagnostic circuit, the frontal deceleration sensor, etc.
If the center airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1615/14 is recorded when a malfunction is detected in the front airbag sensor LH circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1615/14
  1. The center airbag sensor assembly receives a line short circuit, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.
  2. Front airbag sensor LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Engine room main wire
  2. Wiring cowl to headlight harness assembly
  3. Front airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM


H002750E10


INSPECTION PROCEDURE

1.CHECK DTC


    H045190E01
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1615/14 is not output.

    HINT:
    Codes other than DTC B1615/14 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)


    C111981E01
  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH.

  1. Using a service wire, connect B4-30 (+SL) and B4-28 (-SL) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    A13-2 (+SL) -
    A13-1 (-SL)
    Always
    Below 1 Ω



NG
Go to step 8
OK


4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)


    C111977E02
  1. Disconnect the service wire from connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    A13-2 (+SL) -
    A13-1 (-SL)
    Always
    1 MΩ or higher



NG
Go to step 9
OK


5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)


    C111977E02
  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    A13-2 (+SL) -
    Body ground
    Always
    1 MΩ or higher
    A13-1 (-SL) -
    Body ground
    Always
    1 MΩ or higher



NG
Go to step 10
OK


6.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)


    C111977E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    A13-2 (+SL) -
    Body ground
    Ignition switch ON
    Below 1 V
    A13-1 (-SL) -
    Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 11
OK


7.CHECK FRONT AIRBAG SENSOR LH


    H045187E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1615/14 is output.
    A
    DTC B1610/13 is output.
    B
    DTC B1610/13 and B1615/14 are not output.
    C

    HINT:
    Codes other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

B
REPLACE FRONT AIRBAG SENSOR LH
C

USE SIMULATION METHOD TO CHECK 

8.CHECK ENGINE ROOM MAIN WIRE (OPEN)


    C111982E01
  1. Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.

    HINT:
    The service wire has already been inserted into connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    AB2-2 (+SL) -
    AB2-4 (-SL)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE WIRING COWL TO HEADLIGHT HARNESS ASSEMBLY 

9.CHECK ENGINE ROOM MAIN WIRE (SHORT)


    C111980E02
  1. Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    AB2-2 (+SL) -
    AB2-4 (-SL)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE WIRING COWL TO HEADLIGHT HARNESS ASSEMBLY 

10.CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)


    C111980E02
  1. Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    AB2-2 (+SL) -
    Body ground
    Always
    1 MΩ or higher
    AB2-4 (-SL) -
    Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE WIRING COWL TO HEADLIGHT HARNESS ASSEMBLY 

11.CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)


    C111980E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    AB2-2 (+SL) -
    Body ground
    Ignition switch ON
    Below 1 V
    AB2-4 (-SL) -
    Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE WIRING COWL TO HEADLIGHT HARNESS ASSEMBLY