Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › OIL PUMP

OIL PUMP > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT OIL PUMP BODY O-RING


    D025646
  1. Remove the O-ring from the oil pump assembly.



2. REMOVE OIL PUMP ASSEMBLY


    Q003426E01
  1. Place the oil pump body on the torque converter clutch.



3. REMOVE CLUTCH DRUM OIL SEAL RING


    AT08412
  1. Remove the 2 oil rings.



4. REMOVE STATOR SHAFT THRUST BEARING RACE


    AT08670
  1. Remove the stator shaft thrust bearing race.



5. REMOVE STATOR SHAFT ASSEMBLY


    AT08411
  1. Remove the 13 bolts, and then remove the stator shaft from the oil pump body.

  1. Remove the oil pump body from the torque converter clutch.



6. INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY


    AT05153
  1. Using a dial indicator, measure the inside diameter of the oil pump body bushing.

    Maximum inside diameter:
    38.19 mm (1.5035 in.)

    If the inside diameter is greater than the maximum, replace the oil pump body.



7. INSPECT STATOR SHAFT ASSEMBLY


    AT05357
  1. Using a dial indicator, measure the inside diameter of the stator shaft bushing.

    Maximum inside diameter:
    Front side:
    21.58 mm (0.8496 in.)
    Rear side::
    27.08 mm (1.0661 in.)

    If the inside diameter is grater than the maximum, replace the stator shaft.



8. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY


    AT00153
  1. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.07 to 0.15 mm (0.0028 to 0.0059 in.)

    Maximum body clearance:
    0.2 mm (0.0079 in.)

    If the body clearance is greater than the maximum, replace the drive gear, the driven gear or the pump body.



    AT00154
  1. Using a feeler gauge, measure the clearance between the driven gear teeth and the crescent shaped part of the pump body.

    Standard tip clearance:
    0.004 to 0.248 mm (0.0002 to 0.0098 in.)

    Maximum tip clearance:
    0.3 mm (0.012 in.)

    If the tip clearance is greater than the maximum, replace the drive gear, the driven gear or the pump body.



    AT00155
  1. Using a steel straight edge and a feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.0008 to 0.0020 in.)

    Maximum side clearance:
    0.1 mm (0.004 in.)

  1. There are 5 different thickness for drive and driven gears.
    Drive and driven gears thickness: mm (in.) 
    Mark
    Thickness
    F
    10.690 to 10.699 (0.4209 to 0.4212)
    G
    10.700 to 10.709 (0.4213 to 0.4216)
    H
    10.710 to 10.720 (0.4217 to 0.4220)
    J
    10.721 to 10.730 (0.4221 to 0.4224)
    K
    10.731 to 10.740 (0.4225 to 0.4228)
    If the side clearance is greater than the maximum, replace the drive gear, the driven gear or the pump body.



9. REMOVE FRONT OIL PUMP DRIVE GEAR


    D025799
  1. Remove the oil pump drive gear.



10. REMOVE FRONT OIL PUMP DRIVEN GEAR


    D025800
  1. Remove the oil pump driven gear.



11. REMOVE FRONT OIL PUMP OIL SEAL


    AT05152
  1. Using a screwdriver, remove the oil seal.

    NOTICE:
    Be careful not to damage the bushing and the oil pump body.