OVERDRIVE DIRECT CLUTCH > DISASSEMBLY |
| 1. INSPECT OVERDRIVE 1 WAY CLUTCH |
![]() |
Hold the O/D direct clutch drum, and turn the input shaft. Check that the input shaft can be turned freely clockwise and locked counterclockwise.
| 2. REMOVE OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY |
![]() |
Remove the overdrive direct clutch.
| 3. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the clutch drum bushings.
| 4. INSPECT PISTON STROKE OF OVERDRIVE DIRECT CLUTCH |
![]() |
Place the oil pump onto the torque converter clutch, and then place the O/D direct clutch assembly onto the oil pump.
![]() |
Using SST and a dial indicator, measure the O/D direct clutch piston stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| No. | Thickness | No. | Thickness |
| 08 | 3.8 mm (0.150 in.) | 04 | 3.4 mm (0.134 in.) |
| 07 | 3.7 mm (0.146 in.) | 03 | 3.3 mm (0.130 in.) |
| 06 | 3.6 mm (0.142 in.) | 02 | 3.2 mm (0.126 in.) |
| 05 | 3.5 mm (0.138 in.) | 01 | 3.1 mm (0.122 in.) |
| 5. REMOVE OVERDRIVE DIRECT CLUTCH CLUTCH DISC |
![]() |
Using a screwdriver, remove the snap ring from the O/D direct clutch drum.
Remove the flange, the 2 plates and the 2 discs.
| 6. INSPECT OVERDRIVE DIRECT CLUTCH CLUTCH DISC |
![]() |
Check to see if the sliding surfaces of the disc, the plate and the flange are worn or burnt. If necessary, replace them.
| 7. REMOVE OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the spring retainer, and compress the return spring with a press.
Using snap ring pliers, remove the snap ring.
Remove the piston return spring.
| 8. INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Measure the free length of the spring together with the spring seat.
| 9. REMOVE OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Place the oil pump onto the torque converter clutch, and then place the O/D direct clutch onto the oil pump.
Hold the O/D direct clutch piston by hand, and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump to remove the O/D direct clutch piston.
Remove the O/D direct clutch piston.
Remove the 2 O-rings from the piston.
| 10. INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Check that the check ball is free by shaking the piston.
Check that the valve does not have leaks by applying low-pressure compressed air.
| 11. REMOVE OVERDRIVE PLANETARY RING GEAR FLANGE |
![]() |
Using a screwdriver, remove the snap ring.
![]() |
Remove the ring gear flange.
| 12. REMOVE OVERDRIVE RETAINING PLATE |
![]() |
Using a screwdriver, remove the snap ring.
![]() |
Remove the retaining plate.
| 13. REMOVE OVERDRIVE 1 WAY CLUTCH |
![]() |
Remove the overdrive 1 way clutch outer race.
| 14. REMOVE OVERDRIVE 1 WAY CLUTCH |
![]() |
Remove the O/D one-way clutch with the retainer from the outer race.
Remove the 2 retainers from the one-way clutch.
| 15. REMOVE OVERDRIVE PLANETARY GEAR THRUST WASHER NO.3 |
![]() |
Remove the over drive planetary gear thrust washer.
| 16. INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the planetary gear bushing.
![]() |
Using a feeler gauge, measure the planetary pinion gear thrust clearance.