Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    U0001/A2    High Speed CAN Communication Bus

for Preparation Click here


DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communications with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine rpm, required engine torques, warning indicators in the combination meter, DTCs and other data. The ECM sends signals to the TCM concerning engine rpm, opening angles of the throttle valve, temperature of intake air, temperature of engine coolant, engine torques and other data. If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN system, illuminate the MIL and set a DTC.

DTC No.
DTC Detection Condition
Trouble Area
U0001/A2
No communication from TCM continues
  1. Open or short in TCM and ECM circuit
  2. TCM
  3. ECM

WIRING DIAGRAM


A113695E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK ECM (VC, +B AND E1 TERMINALS)


    A066060E10
  1. Measure the voltage and resistance of the ECM connectors.

    Standard:
    Tester Connection
    Ignition Switch Condition
    Specified Condition
    B9-1 (+B) - Body ground
    ON
    9 to 14 V
    D1-18 (VC) - Body ground
    ON
    4.5 to 5.5 V
    D3-7 (E1) - Body ground
    -
    10 kΩ or higher



NG
CHECK ECM POWER SOURCE CIRCUIT
OK


2.CHECK TRANSMISSION CONTROL MODULE (IG2 AND E1 TERMINAL2)


    G039048E01
  1. Measure the voltage and resistance of the TCM connectors.

    Standard voltage:
    Tester Connection
    Ignition switch Condition
    Specified Condition
    O3-6 (IG2) - Body ground
    Ignition switch ON
    9 to 14 V

    Standard resistance:
    Tester Connection
    Ignition switch Condition
    Specified Condition
    O1-1 (E1) - Body ground
    Always
    10 kΩ or higher



NG
CHECK TRANSMISSION CONTROL MODULE POWER SOURCE CIRCUIT
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU - ECM)


    G034917E01
  1. Disconnect the B7 ECM connector.

  1. Disconnect the O3 TCM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B7-22 (CAN+) - O3-21 (CAN+)
    Below 1 Ω
    B7-21 (CAN-) - O3-22 (CAN-)
    Below 1 Ω
    B7-22 (CAN+) or O3-21 (CAN+) - Body ground
    10 kΩ or higher
    B7-21 (CAN-) or O3-22 (CAN-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.CHECK IF DTC OUTPUT RECURS
  1. Clear the DTC (Click here).

  1. Replace the TCM.

    HINT:
    Replace the TCM with a TCM from a normally functioning vehicle of the same model.

  1. Start the engine.

  1. Read the DTCs (Click here).

    Result:

    Display (DTC Output)
    Proceed to
    U0001/A2
    A
    No DTC
    B



B
REPLACE TRANSMISSION CONTROL MODULE ASSEMBLY
A

REPLACE ECM