Home › ENGINE ยท 2KD-FTV › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL TIGHT PLUG


    A058129E01
  1. Apply adhesive to the end of new tight plugs.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent

    NOTICE:
    Do not start the engine for 1 hour after the installation.



  1. Using SST and a hammer, tap in the tight plugs as shown in the illustration.


    A101007E01

  1. Position A:
    Using 14 mm steel bar and a hammer, tap in the tight plug as shown in the illustration.

  1. Other Positions:
    Position B

    SST
    09950-60010   (09951-00180)
    09950-70010   (09951-07100)
    Position C
    SST
    09950-60010   (09951-00190)
    09950-70010   (09951-07100)
    Position D
    SST
    09950-60010   (09951-00200)
    09950-70010   (09951-07100)
    Position E
    SST
    09950-60010   (09951-00350)
    09950-70010   (09951-07100)
    Position F
    SST
    09950-60010   (09951-00400)
    09950-70010   (09951-07100)
    Position G
    SST
    09950-60010   (09951-00450)
    09950-70010   (09951-07100)



2. INSTALL END PLATE STRAIGHT PIN


    A103301E01
  1. Install the end plate straight pins as shown in the illustration.



3. INSTALL ENGINE REAR OIL SEAL STRAIGHT PIN


    A103299E01
  1. Install the engine rear oil seal straight pins as shown in the illustration.



4. INSTALL TIMING GEAR COVER SET STRAIGHT PIN


    A103300E02
  1. Install the timing gear cover set straight pins as shown in the illustration.



5. REMOVE CYLINDER HEAD SET RING PIN


  1. Install the cylinder head set ring pins as shown in the illustration.


    A061388E02



6. INSTALL STUD BOLT


  1. Install the stud bolts as shown in the illustration.


    G037522E02

    Torque:
    for A and B:
    7.0 N*m{ 70 kgf*cm , 62 in.*lbf }

    Torque:
    for C:
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf }

    Torque:
    for D:
    4.0 N*m{ 40 kgf*cm , 35 in.*lbf }



7. INSTALL SCREW PLUG
  1. Install a new gasket and the screw plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



8. INSTALL OIL NOZZLE NO.1 SUB-ASSEMBLY


    A060268
  1. Align the pin of the oil nozzle with the pin hole of the cylinder block.

  1. Install the oil nozzle with the check valve. Install the 4 oil nozzles and check valves.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



9. INSTALL CONNECTING ROD SMALL END BUSH


    A060210E01
  1. Align the oil holes of a new bush and the connecting rod.



    A060209E01
  1. Using SST and a press, press in the bush.

    SST
    09222-76012  



    A054733
  1. Using a pin hole grinder, hone the bush to obtain the standard specified clearance (see disassembly, step 85) between the bush and piston pin.



  1. Check the piston pin fitting condition at normal room temperature.



      A060207E01
    1. Coat the piston pin with engine oil, and push it into the connecting rod with your thumb.



10. INSTALL PISTON SUB-ASSEMBLY W/PIN


    A052280
  1. Using a screwdriver, install a new snap ring on one side of the piston hole.

    NOTICE:
    Install the snap ring so that either of snap ring ends A or B is aligned with the cutout on the piston.



    A060230
  1. Gradually heat the piston to about 80°C (176°F).

  1. Coat the piston pin with engine oil.



    A060208E01
  1. Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.



    A060231E02
  1. Check the fitting condition between the piston and piston pin. Try to move the piston back and forth on the piston pin.



    A060202
  1. Using a screwdriver, install a new snap ring on the other side of the piston pin hole.

    HINT:
    Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



11. INSTALL PISTON RING SET


    A052282
  1. Install the oil ring coil by hand.



    A103289E01
  1. Using a piston ring expander, install the 2 oil rings.



    A061389E01
  1. Using a piston ring expander, install the No.1 and No.2 piston rings with the code mark facing upward.

    Code mark:
    Ring
    Mark
    No.1
    N
    No.2
    NP



    A059180E01
  1. Position the piston rings so that the ring ends are as shown.

    NOTICE:
    Do not align the ring ends.



12. INSTALL CRANKSHAFT

HINT:
Upper bearings have an oil groove and oil hole. Lower bearings do not.



    A101023
  1. Align the bearing claw with the claw groove of the cylinder block, and push in the 5 upper bearings.



    A052224E01
  1. Align the bearing claw with the claw groove of the crankshaft bearing cap, and push in the 5 lower bearings.

  1. Place the crankshaft on the cylinder block.



    A060188E01
  1. Install the 2 upper thrust washers to the No.5 journal position of the cylinder block.

  1. Push the crankshaft toward the front (rear) side.

  1. Install the 2 thrust washers with the oil grooves facing outward.



    A060189E01
  1. Install the 2 thrust washers on the No.5 bearing cap with the grooves facing outward.



    A060226
  1. Install the 5 crankshaft bearing caps in their proper locations.



  1. Install the crankshaft bearing cap bolts.

    HINT:
    1. The main bearing cap bolts are tightened in 2 progressive steps (steps [*1] and [*2]).
    2. If a main bearing cap bolt is broken or deformed, replace it.


    1. Apply a light coat of the engine oil to the threads and under the bolt heads of the main bearing caps.



    2. A060270E07
    3. Install and uniformly tighten the 10 bolts of the main bearing caps in several steps in the sequence shown in the illustration. [*1]

      Torque:
      50 N*m{ 510 kgf*cm , 37 ft.*lbf }

      If any one of the bearing cap bolts does not meet the torque specification, replace the bearing cap bolt.

    4. Mark the front of the main bearing cap bolt with paint.



    5. A060271E02
    6. Retighten the main bearing cap bolts 90° in the numerical order shown above. [*2]

    7. Check that the painted mark is now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

  1. Check the crankshaft thrust clearance (see disassembly, step 73).



13. INSTALL CONNECTING ROD SUB-ASSEMBLY


    A052286E01
  1. Align the bearing claw with the groove of the connecting rod or connecting cap.

  1. Install the bearings in the connecting rod and connecting rod cap.



    A059180E01
  1. Position the piston rings so that the ring ends are as shown.



    A101030E01
  1. Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.



  1. Place the connecting rod cap on the connecting rod.

    1. Match the numbered connecting rod cap with the connecting rod.



    2. A101031
    3. Align the pins of the connecting rod cap with the pin holes of the connecting rod, and install the connecting rod cap.



    4. A101032E01
    5. Check that the front mark of the connecting rod cap is facing forward.



  1. Install the connecting rod cap bolts.

    HINT:
    The connecting rod cap bolts are tightened in 2 progressive steps (steps [*1] and [*2]).

    If any connecting rod bolt is broken or deformed, replace it.

    1. Apply a light of engine oil to the threads and under the heads of the connecting rod cap bolts.



    2. A101033
    3. Install and alternately tighten the bolts of the connecting rod cap in several steps. [*1]

      Torque:
      35 N*m{ 357 kgf*cm , 26 ft.*lbf }

      HINT:
      If any one of the connecting rod cap bolts does not meet the torque specification, replace the cap bolts.



    4. A060197E03
    5. Mark the front of the connecting rod cap bolts with paint.

    6. Retighten the connecting rod cap bolts 90° as shown. [*2]

    7. Check that the painted mark is now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

  1. Check the connecting rod thrust clearance (see disassembly, step 67).



14. INSTALL CYLINDER BLOCK OIL ORIFICE


    A077144E01
  1. Install the cylinder block oil orifice to the cylinder block.



15. INSTALL TIGHT PLUG


    A058129E01
  1. Apply adhesive to new tight plugs.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent



  1. Using SST and a hammer, tap in the tight plugs as shown in the illustration.


    A100967E03


    1. Position A

      SST
      09950-60010   (09951-00200)
      09950-70010   (09951-07100)

    2. Position B

      SST
      09950-60010   (09951-00300)
      09950-70010   (09951-07100)

    3. Position C

      SST
      09950-60010   (09951-00350)
      09950-70010   (09951-07100)



16. INSTALL RING PIN


  1. Install the ring pins as shown in the illustration.


    A100969E01



17. INSTALL STUD BOLT


  1. Install the stud bolts as shown in the illustration.


    A100968E03

    Torque:
    for A (Thread Diameter 10 mm):
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    Torque:
    for B (Thread diameter 8 mm):
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }

    Torque:
    for C (Thread diameter 6 mm):
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }

    Torque:
    for D (Thread diameter 6 mm):
    7.0 N*m{ 70 kgf*cm , 62 in.*lbf }

    Torque:
    for E (Thread diameter 6 mm):
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }



18. INSTALL STRAIGHT SCREW PLUG NO.1


  1. Apply adhesive to the end of the screw plug.


    A100970E01

    Adhesive:
    08833-00070, THREE BOND 1324 or equivalent

  1. Using a 6 mm hexagon wrench, install the screw plug.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



19. INSTALL SEMICIRCULAR PLUG
  1. Remove any old packing (FIPG) material.



  1. Apply seal packing to the oil seal retainer as shown in the illustration.


    A100971E01

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    1. The semicircular plug must be installed within 3 minutes after the completion of applying the seal packing.
    2. Prevent FIPG from being stuck to the camshaft thrust groove.

  1. Install the semicircular plug to the cylinder head.



20. INSTALL VALVE SPRING SEAT PLATE WASHER


    A051419
  1. Install the valve spring seat plate washers to the cylinder head.



21. INSTALL VALVE STEM OIL SEAL


    A102746E01
  1. Using SST, push in a new oil seal.

    SST
    09201-41020  



22. INSTALL INTAKE VALVE
  1. Apply plenty of engine oil to the valve stem tip.

  1. Install the valve, spring seat, compression spring and spring retainer.



    A110764E01
  1. Using SST, compress the compression spring and place the 2 keepers around the valve stem.

    SST
    09202-70020   (09202-00020)



    A051454
  1. Using a plastic hammer, lightly tap the valve stem tip to assure a proper fit.

    NOTICE:
    Do not damage the valve stem tip.



23. INSTALL EXHAUST VALVE
  1. Apply plenty of engine oil to the valve stem tip.

  1. Install the valve, spring seat, compression spring and spring retainer.



    A102742E01
  1. Using SST, compress the compression spring and place the 2 keepers around the valve stem.

    SST
    09202-70020   (09202-00020)



    A051455
  1. Using a plastic hammer, lightly tap the valve stem tip to assure a proper fit.

    NOTICE:
    Do not damage the valve stem tip.



24. INSTALL VALVE LIFTER
  1. Apply plenty of engine oil to the valve lifters.

  1. Install the valve lifters.

  1. Check that the valve lifter rotates smoothly by hand.



25. INSTALL SUPPLY PUMP GEAR BEARING


    A100872E01
  1. Using SST and a press, press in a new bearing.

    SST
    09223-00010  
    09223-15020  
    09502-12010  
    09950-70010   (09951-07100)



26. INSTALL ENGINE REAR OIL SEAL


    A102763E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.

    SST
    09223-15030  
    09950-70010   (09951-07200)

    Oil seal depth from the flat-end surface:
    0 to -0.5 mm (0 to -0.020 in.)

  1. Apply MP grease to the oil seal lip.

    NOTICE:
    Keep the lip clean. Prevent dirt and dust from adhering to that area.



27. INSTALL ENGINE REAR OIL SEAL RETAINER


    A110887E01
  1. Apply seal packing to the specific places described in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    Seal width:
    4.0 mm (0.16 in.)

    NOTICE:
    After applying FIPG, install the engine rear oil seal retainer within 3 minutes and tighten its bolts within 15 minutes.



    A051412
  1. Install the retainer with the 5 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



28. INSTALL TIMING GEAR CASE ASSEMBLY


    A102777E02
  1. Install 2 new O-rings to the cylinder block grooves.



    A052300
  1. Install the stud bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Remove any old packing (FIPG) material.

  1. Install the oil pump rotor to the timing gear case.



    A100876E01
  1. Install a new gasket to the groove of the timing gear case.



    A100875E02
  1. Apply seal packing to the timing gear case as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    Seal width:
    4.0 mm (0.16 in.)

    NOTICE:
    Install the timing gear case assembly within 3 minutes and tighten its bolts within 15 minutes after applying FIPG is competed.



    A100878E01
  1. Install the timing gear case with the union bolt and 8 bolts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf } for union bolt (A)
    13 N*m{ 133 kgf*cm , 10 ft.*lbf } for other bolts

  1. Remove the screw plug.



    A102910
  1. Pour approximately 50 cc (1.7 fl.oz) of engine oil into the oil pump.

  1. Reinstall a new gasket and the screw plug.

    Torque:
    42 N*m{ 423 kgf*cm , 31 ft.*lbf }



29. INSTALL OIL STRAINER SUB-ASSEMBLY


    A102736
  1. Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



30. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material.



    A100880E03
  1. Apply seal packing to the oil pan as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    Seal width:
    4.0 mm (0.16 in.)

    NOTICE:
    Install the oil pan assembly within 3 minutes and tighten its bolts within 15 minutes after applying FIPG is competed.



    A074128E01
  1. Install the oil pan with the 22 bolts and 2 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. Install a new gasket and the drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



31. INSTALL SUPPLY PUMP GEAR


    A077139
  1. Install the supply pump with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A069844
  1. Temporarily install the O-ring and supply pump gear with the nut.

    HINT:
    Fit the key (protrusion) of the supply pump to the key slot of the supply pump gear.



    A100864E01
  1. Using SST, tighten the nut.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



32. INSTALL CRANKSHAFT TIMING GEAR


    A100881E01
  1. Face the crankshaft timing gear with timing mark 1 facing forward.

  1. Align the set key on the crankshaft with the key groove of the crankshaft timing gear.

  1. Using SST and a hammer, tap in the timing gear.

    SST
    09223-00010  



33. INSTALL IDLE GEAR SHAFT NO.1


    A069846
  1. Coat the idle gear shaft No.1 with engine oil as shown in the illustration.



    A100885E01
  1. Install the gear shaft.



34. INSTALL IDLE SUB GEAR NO.2


    A101042
  1. Mount the idler gear No.1 in a vise as shown in the illustration.

    NOTICE:
    Do not damage the gear.



    A102737E01
  1. Install the gear spring.

  1. Install the sub gear No.2.

    HINT:
    Align the pins on the gears with the spring ends.

  1. Install the wave washer.



    A100883
  1. Using snap ring pliers, install the snap ring.



    A100884E01
  1. Using SST, align the holes of the idler main gear and sub gears by turning the sub gear clockwise, and install a service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    SST
    09960-10010   (09962-01000, 09963-00600)

    HINT:
    Align the gear teeth of the main gear and sub gear, and tighten the service bolt.

    Recommended service bolt: 
    Thread diameter
    6 mm
    Thread pitch
    1.0 mm
    Bolt length
    Approx. 28 mm (1.1 in.)



35. INSTALL IDLE GEAR NO.1


    A100886E01
  1. Align the "5" timing marks of the idle gear and crankshaft timing gear.

  1. Using SST, turn the supply pump gear, and align the "4" timing marks of the idle gear and supply pump gear, and mesh the gears.

    SST
    09960-10010   (09962-01000, 09963-00600)



36. INSTALL CRANKSHAFT POSITION SENSOR PLATE NO.1


    A100888E01
  1. Align the set key with the key groove of the sensor plate.

  1. Install the sensor plate with the cup side facing outward.



37. INSTALL IDLE GEAR THRUST PLATE


    A069855
  1. Face the thrust plate with the protrusion facing outward.



    A100887E01
  1. Align the bolt holes, and install the thrust plate with the 2 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



38. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


    A102764E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

    SST
    09608-32010  
    09950-70010   (09951-07100)

    Oil seal depth from the flat-end surface:
    0 to -0.5 mm (0 to -0.020 in.)

  1. Apply MP grease to the oil seal lip.

    NOTICE:
    Keep the lip clean. Prevent dirt and dust from adhering to that area.



39. INSTALL TIMING CHAIN OR BELT COVER OIL SEAL


    A102765E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

    SST
    09649-17010  
    09950-70010   (09951-07100)

    Oil seal depth from the flat-end surface:
    0 to -0.5 mm (0 to -0.020 in.)

  1. Apply MP grease to the oil seal lip.

    NOTICE:
    Keep the lip clean. Prevent dirt and dust from adhering to that area.



40. INSTALL TIMING GEAR CASE


    A051376
  1. Remove the service bolt.



    A100894E01
  1. Install a new O-ring to the timing gear case assembly.



    A110888E02
  1. Apply seal packing to the timing gear case as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    Seal width:
    4.0 mm (0.16 in.)

    NOTICE:
    Install the timing gear case within 3 minutes and tighten its bolts within 15 minutes after applying FIPG is competed.



    A100853
  1. Install the timing gear case with the 14 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



41. INSTALL WATER PUMP ASSEMBLY


    A100852
  1. Install a new gasket and the water pump with the 5 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



42. INSTALL CYLINDER HEAD SUB-ASSEMBLY


  1. Check the piston protrusions for each cylinder.

    1. Clean the cylinder block with solvent.

    2. Set the piston of the cylinder to be measured to slightly before TDC.



    3. A103245E01
    4. Place a dial indicator on the cylinder block, and set the measuring tip as shown in the illustration.

    5. Set the dial indicator at 0 mm (0 in.).

      HINT:
      Make sure that the measuring tip is square to the cylinder block gasket surface and piston head when taking the measurements.

    6. Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.

    7. Measure each cylinder at 2 places as shown in the illustration, making a total of 8 measurements.

    8. For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

      HINT:
      If the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall it.

      Piston protrusion:
      0.005 to 0.254 mm (0.0002 to 0.0100 in.)



    A102770E01
  1. Select a new cylinder head gasket.

    HINT:
    Cylinder head gaskets are marked A, B, C, D or E accordingly.

    New installed cylinder head gasket thickness:
    Cutout mark
    Thickness
    A
    0.80 to 0.90 mm (0.0315 to 0.0354 in.)
    B
    0.85 to 0.95 mm (0.0335 to 0.0374 in.)
    C
    0.90 to 1.00 mm (0.0354 to 0.0394 in.)
    D
    0.95 to 1.05 mm (0.0374 to 0.0413 in.)
    E
    1.00 to 1.10 mm (0.0394 to 0.0433 in.)


    1. Select the largest piston protrusion value from the measurements made and then select a new appropriate gasket according to the table below.
      Piston protrusion
      Gasket size
      0.005 to 0.054 mm (0.0002 to 0.0021 in.)
      Use A
      0.055 to 0.104 mm (0.0022 to 0.0041 in.)
      Use B
      0.105 to 0.154 mm (0.0041 to 0.0061 in.)
      Use C
      0.155 to 0.204 mm (0.0061 to 0.0080 in.)
      Use D
      0.205 to 0.254 mm (0.0081 to 0.0100 in.)
      Use E



    A100847E06
  1. Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.



    A100901E01
  1. Place the cylinder head gasket in position on the cylinder block.

  1. Place the cylinder head on the cylinder block.

    NOTICE:
    Be careful of the installation direction.



  1. Install the cylinder head bolts.

    HINT:
    1. The cylinder head bolts are tightened in 3 progressive steps (steps [*1], [*2] and [*3]).
    2. If any bolts is broken or deformed, replace it.


    1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



    2. A111003E01
    3. Install and uniformly tighten the 18 cylinder head bolts, in several steps in the sequence shown in the illustration. [*1]

      Torque:
      85 N*m{ 867 kgf*cm , 63 ft.*lbf }

      Bolt length:
      110 mm (4.33 in.) for A
      167 mm (6.57 in.) for B

      If any one of the cylinder head bolts does not meet the torque specification, replace the cylinder head bolt.



    A051382E02
  1. Mark the front of the cylinder head bolt with paint.

  1. Retighten the cylinder head bolts by 90° in the sequence shown in the illustration. [*2]

  1. Retighten the cylinder head bolts by an additional 90°. [*3]

  1. Check that the painted mark is now facing rearward.



43. INSTALL CAMSHAFT


    A100847E07
  1. Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

    HINT:
    Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.



  1. Install the camshaft.

    1. Apply MP grease to the thrust portion of the camshafts.



    2. A100849E01
    3. Place the camshaft on the cylinder head and face the key groove upward.



    4. A100906E01
    5. Align the timing marks (1 dot mark) of the camshaft drive and driven main gears, and place the No. 2 camshaft.



    6. A100908
    7. Install the 5 bearing caps in their proper locations.

    8. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.



    9. A100909E01
    10. Install and uniformly tighten the 10 bearing cap bolts, in several steps in the sequence shown.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }



44. INSTALL TIMING BELT NO.2 COVER


    A051300
  1. Install the timing belt No. 2 cover with the 4 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



45. INSTALL CAMSHAFT TIMING PULLEY
  1. Install the set key to the key groove of the camshaft.

  1. Align the set key with the key groove of the timing pulley.



    A100912
  1. Hold the hexagon portion of the camshaft, and install the timing pulley with the bolt.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }



46. INSPECT VALVE CLEARANCE


  1. Inspect the valve clearance.



      A051389E02
    1. Lower the piston by rotating the crankshaft about 90° counterclockwise from the TDC position.

    2. Align the timing mark of the camshaft timing pulley with the arrow mark of the timing belt No.2 cover.



    3. A100914E01
    4. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Valve clearance (cold):

      Clearance
      Intake
      0.20 to 0.30 mm (0.0079 to 0.0118 in.)
      Exhaust
      0.35 to 0.45 mm (0.0138 to 0.0177 in.)

    5. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.



    A100915E01
  1. Turn the camshaft 1/2 revolutions (180°).

  1. Check only the valves indicated in the illustration. Measure the valve clearance (see procedure (a) above).



47. REMOVE CAMSHAFT TIMING PULLEY


    A100848
  1. Remove the bolt for the camshaft timing pulley by holding the camshaft with a wrench.



    A115888E01
  1. Using SST, remove the camshaft timing pulley and set key.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)



    A100847E05
  1. Rotate the crankshaft about 90° counterclockwise from the TDC position to lower the piston.



48. REMOVE TIMING BELT NO.2 COVER


    A051300
  1. Remove the nut, 4 bolts and timing belt No.2 cover.



49. REMOVE NO.2 CAMSHAFT


    A100849E01
  1. Face the key groove of the camshaft upward by turning the camshaft with a wrench.



    A100850E01
  1. Uniformly loosen the 15 bearing cap bolts in several steps in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.



    A051302
  1. Remove the No.2 camshaft.



50. REMOVE CAMSHAFT


    A051303
  1. Remove the camshaft.



51. ADJUST VALVE CLEARANCE


  1. Adjust the valve clearance.

    HINT:
    Determine the replacement valve lifter size according to the chart and formula:




      A033166E01
    1. Using a micrometer, measure the thickness of the removed litter.

    2. Calculate the thickness of a new lifter so the valve clearance comes within the specified value.
      A
      Thickness of new lifter
      B
      Thickness of used lifter
      C
      Measured valve clearance

      Valve clearance:
      Intake A = B + (C -0.25 mm (0.0098 in.))
      Exhaust A = B+ (C -0.40 mm (0.0158 in.))

    3. Select a new lifter with a thickness as close as possible to the calculated values.

      HINT:
      Valve lifters are available in 35 sized in increments of 0.020 mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).



  1. Valve lifter selection chart (Intake).


    A072846E03

    HINT:
    EXAMPLE: The 5.250mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0158 in.). Replace the 5.250 mm (0.2067 in.) shim with a new No. 40 lifter.

    Intake valve clearance (Cold):
    0.20 to 0.30 mm (0.0079 to 0.0118 in.)



  1. Valve lifter selection chart (Exhaust).


    A072845E04

    HINT:
    EXAMPLE: The 5.340mm (0.2102 in.) lifter is installed, and the measured clearance is 0.480 mm (0.0189 in.). Replace the 5.340 mm (0.2102 in.) shim with a new No. 42 lifter.

    Exhaust valve clearance (Cold):
    0.35 to 0.45 mm (0.0138 to 0.00177 in.)

  1. Install the selected valve lifter.



52. INSTALL CAMSHAFT


    A100847E07
  1. Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

    HINT:
    Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.



  1. Install the camshaft.

    1. Apply MP grease to the thrust portion of the camshafts.



    2. A100849E01
    3. Place the camshaft on the cylinder head and face the key groove upward.



    4. A100906E01
    5. Align the timing marks (1 dot mark) of the camshaft drive and driven main gears, and place the No. 2 camshaft.



    6. A100907E01
    7. Apply seal packing to the No. 1 bearing cap.

      Seal packing:
      Part No. 08826-00080 or equivalent

      Seal width:
      4 mm (0.16 in.)

      NOTICE:
      1. Beware that FIPG does not stick to the oil passage of the bearing cap.
      2. Once completed applying FIPG, install the camshaft bearing cap within 3 minutes and fasten its bolts within 15 minutes.
      3. Do not start the engine for 2 hours after the installation.



    8. A100908
    9. Install the 5 bearing caps in their proper locations.

    10. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.



    11. A100909E01
    12. Install and uniformly tighten the 10 bearing cap bolts, in several steps in the sequence shown.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }



53. INSTALL CAMSHAFT SETTING OIL SEAL


  1. Install the camshaft oil seal.

    1. Apply MP grease to a new oil seal lip.

      NOTICE:
      Keep the lip free from foreign objects.



    2. A102766E01
    3. Using SST and a hammer, tap in the oil seal until its surface is flush with the cylinder head edge.

      SST
      09608-06041  

      Oil seal depth from the flat-end surface:
      0.5 to -1.5 mm (0.020 to -0.059 in.)



54. INSTALL TIMING BELT NO.2 COVER


    A100911E01
  1. Apply seal packing to the timing gear cover as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    Install the timing belt No. 2 cover within 3 minutes and tighten its bolts and nut within 15 minutes after applying FIPG is competed.



    A051300
  1. Install the timing belt No. 2 cover with the 4 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



55. INSTALL CAMSHAFT TIMING PULLEY
  1. Install the set key to the key groove of the camshaft.

  1. Align the set key with the key groove of the timing pulley.



    A100912
  1. Hold the hexagon portion of the camshaft, and install the timing pulley with the bolt.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }



56. INSTALL INJECTOR ASSEMBLY


    A076599
  1. Install the common rail with the 2 bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Install 4 new injection nozzle sheets to the cylinder head.

  1. Apply a light coat of clean engine oil to new O-rings.



    A100921E01
  1. Install the O-ring to each injector as shown in the illustration.



    A076605
  1. Insert the 4 injectors into the cylinder head.

    NOTICE:
    1. At this time, insert the injector until it touches the nozzle sheet surface.
    2. After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it again.
    3. Always return an injector to the same place it was removed from.



    B012460
  1. Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.

    HINT:
    If scratches or dents are present, replace the nozzle leakage pipe.



    A076602E01
  1. Install the nozzle leakage pipe and 5 new gaskets.

  1. Apply a light coat of oil onto the 4 hollow screws and union bolt.

  1. Temporarily install the nozzle leakage pipe with the 4 hollow screws and union bolt.

    NOTICE:
    Make sure that the injector hollow screw and union bolt are not deformed or damaged.



    A076603
  1. Temporarily install the 4 injection pipes.

    NOTICE:
    For positioning the injectors, loosely tighten the union nut.



    A100922E01
  1. Set the holder clamps to each injector as shown in the illustration.

  1. Set new washers on the nozzle holder clamps as shown in the illustration.

  1. Tighten the bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }

    NOTICE:
    1. The fork portion of the nozzle holder clamp must be set in the groove of the injector, not other portion.
    2. Before tightening the bolts, check that the nozzle holder clamp is set properly.
    3. To fasten the clamp bolts, temporarily tighten them by hand until they cannot turn. Then, tighten the bolts to specified torque.
    4. When tightening to a specified torque, pay attention not to tilt the bolt and the clamp.
    5. The washer cannot be reused.
    6. If the nozzle leakage pipe is accidentally tightened beyond the torque specification, it must be replaced.



    A112876E01
  1. Tighten the 4 hollow screws from #1 and #4 in order.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    If any of the screws are overtightened, replace the nozzle leakage pipe with a new one.

  1. Tighten the union bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

    NOTICE:
    If the bolt is overtightened, replace the nozzle leakage pipe with a new one.



    A076603
  1. Remove the 4 injection pipes.



  1. Check that there are no leaks from the nozzle leakage pipe connection.



      G037171E01
    1. Using SST, install the nozzle leakage pipe No.2 and new gasket to the cylinder head.

      SST
      09280-00010  

      Torque:
      21 N*m{ 215 kgf*cm , 15 ft.*lbf }

      HINT:
      Nozzle leakage pipe No. 2: Part No. 23762-27010

    2. Apply a light coat of soapy water (any fluid to detect fuel leakage) to the nozzle leakage pipe connection.



    3. A060186E01
    4. Using SST (turbocharger pressure gauge), apply SST to the fuel return side of the leakage pipe, and maintain 250 kPa (2.5 kgf*cm2, 35.5 psi) of pressure for 60 seconds to check that no bubbles come out.

      SST
      09992-00242  

      NOTICE:
      Be sure to keep specified pressure, preventing from leakage.

      HINT:
      1. Apply a coat of engine oil to the leakage pipe connection, and check that no bubbles come from the leakage pipe connection or each nozzle leakage pipe connection.
      2. Check that the indication on the SST (turbo charger pressure gauge) does not go down while pressure is applied.

    5. Remove the SST, union bolt, bolt and nozzle leakage pipe No.2.



57. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    A100928E01
  1. Apply seal packing to the cylinder head as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    After applynig the seal packing, parts must be assembled within 3 minutes, and then tighten them within 15 minutes.

  1. Install a new gasket to the cylinder head cover.



    A051295
  1. Install the cylinder head cover with 10 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several steps.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



58. INSTALL NOZZLE HOLDER SEAL


    A102858E01
  1. Install 4 new holder seals.



59. INSTALL OIL FILLER CAP SUB-ASSEMBLY


    A074130E01
  1. Install the oil filler cap.