ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
Remove the radiator cap.
Check if there is any excessive deposits of rust or scale around the radiator cap and radiator filler hole. The coolant should be free from oil.
Install the radiator cap.
| 2. INSPECT ENGINE OIL |
Warm up the engine, stop the engine and wait 5 minutes. The oil level should be between the dipstick's low and full level marks.
If the oil level is low, check for leakage and add oil up to the full level mark.
| 3. INSPECT BATTERY |
Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.
Check the electrolyte level of each cell.
For maintenance-free batteries:
For non-maintenance-free batteries:
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element from the air cleaner case.
Visually check that there is no dirt, clog, and damage to the air cleaner filter element.
| 5. INSPECT SPARK PLUG (for Leaded Gasoline Specification Vehicle) |
![]() |
Check the electrode.
Using a megohmmeter, measure the insulation resistance.
![]() |
Alternative inspection method:
Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator.
If there is damage, replace the spark plug. If not, reinstall the spark plug.
| Manufacture | Product |
| DENSO made | K20HR-U11 |
| NGK made | LFR6C-11 |
![]() |
Check the spark plug electrode gap.
![]() |
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
| 6. INSPECT SPARK PLUG (for Unleaded Gasoline Specification Vehicle) |
![]() |
Check the electrode.
Using a megohmmeter, measure the insulation resistance.
![]() |
Alternative inspection method.
Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator.
If there is damage, replace the spark plug. If not, reinstall the spark plug.
| Manufacture | Product |
| DENSO made | SK20HR11 |
| NGK made | ILFR6C11 |
![]() |
Check the spark plug electrode gap.
![]() |
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
| 7. INSPECT VALVE LASH ADJUSTER NOISE |
Rev up the engine several times. Check that the engine does not emit unusual noises. If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the above inspection again.
| 8. INSPECT IGNITION TIMING |
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following items:
Powertrain / Engine and ECT / Data list / IGN Advance
When not using the intelligent tester:
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No.4 cylinder.
Turn the ignition switch to the ON position.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Remove the timing light.
| 9. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following items:
Powertrain / Engine and ECT / Data list / Engine SPD
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
![]() |
When not using the intelligent tester:
Install SST to terminal 9 (TAC) of DLC3, then connect a tachometer.
Turn the ignition switch to the ON position.
Inspect the engine idling speed.
Turn the ignition switch off.
Disconnect the tachometer.
Remove the SST from terminal 9 (TAC).
| 10. INSPECT ENGINE IDLE SPEED CONTROL SYSTEM |
![]() |
Check the idle speed control system.
Using SST, connect terminals TC and CG of the DLC3.
Start the engine and idle it.
![]() |
After connecting terminals (TC and CG), check that the engine speed changes to approximately 1,000 to 1,500 rpm for 5 seconds, and then returns to idle speed.
| 11. INSPECT COMPRESSION |
Warm up and stop the engine.
Remove the intake air connector.
Disconnect the injector connectors.
Remove the ignition coils.
Remove the spark plugs.
![]() |
Check the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
Install the spark plugs.
Install the ignition coils.
Connect the injector connectors.
Install the intake air connector.
| 12. INSPECT CO (for Leaded Gasoline Specification Vehicle) |
Initial condition:
Engine at normal operating temperature
Air cleaner installed
All pipes and hoses of the air induction system connected
All accessories switched off
All vacuum lines properly connected
EFI system wiring connectors fully seated
Ignition timing set correctly
Transmission in the neutral position
Tachometer and CO meter calibration at idle
Warm up the engine by driving at constant speed (approximately 50 km/h (31 mph)). Close the throttle valve for 5 minutes after the engine coolant temperature becomes stable (80 to 90°C (176 to 194°F)) and idle the engine for 5 minutes.
![]() |
Insert a tester probe at least 40 cm (1.3 ft) into the tail pipe.
Wait at least 1 minute before measurement to allow the concentration to stabilize. Complete the measurement within 3 minutes.
![]() |
If the CO concentration does not conform to regulations, adjust it by turning the idle mixture adjusting screw in the variable resistor with SST.
![]() |
The idle mixture adjusting screw can be adjusted within an 180° angle range.
Remove the SST.
| CO | Problems | Causes |
| High | Rough idle (black smoke from exhaust) |
|
| 13. INSPECT CO/HC (for Unleaded Gasoline Specification Vehicle) |
Start the engine.
Run the engine at 2,500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tail pipe while idling.
Check the CO/HC concentration with the engine idling and/or running at 2,500 rpm.
| CO | HC | Problems | Causes |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|