Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › ENGINE COOLANT TEMPERATURE SENSOR

ENGINE COOLANT TEMPERATURE SENSOR > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)


4. REMOVE ENGINE UNDER COVER NO.2 (w/ Engine Under Cover No.2)
  1. Remove the engine under cover No.2 together with the engine side under cover LH and engine side under cover RH (for Wide Body).



5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap.



  1. Loosen the radiator drain plug and a cylinder block drain plug. Then drain the coolant.


    A115990E01



6. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)

HINT:
Use the same procedures described for the LH side.



7. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)

HINT:
Use the same procedures described for the LH side.



8. REMOVE FRONT DOOR SCUFF PLATE RH


9. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the 5 bolts and engine service hole sub cover.



10. REMOVE INTAKE AIR CONNECTOR


    A102437E01
  1. Disconnect the ventilation hose No.2 and the vacuum hose.(A)

  1. Loosen the 2 hose clamp bolts.(B)

  1. Remove the 2 bolts, then remove the intake air connector.(C)



11. REMOVE THROTTLE BODY ASSEMBLY


    A102438E01
  1. Disconnect the throttle motor connector.(A)

  1. Disconnect the water by-pass hose.(B)

  1. Disconnect the water by-pass hose No.2.(C)

  1. Remove the 2 bolts and 2 nuts, then remove the throttle body assembly.(D)



    G037700
  1. Remove the gasket from the intake manifold.



12. DISCONNECT FUEL HOSE


    A087751E01
  1. Pull the fuel hose connector cover up to release the lock. (Click here)

  1. Disengage the fuel connector to disconnect the fuel hose. (Click here)



13. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

NOTICE:
Be careful not to drop the injectors when removing the delivery pipe.



    A087156
  1. Disconnect the fuel hoses.

  1. Disconnect the 4 injector connectors.

  1. Remove the 2 bolts O-ring and fuel pulsation damper assembly.

  1. Remove the 2 bolts and delivery pipe together with the 4 injectors.

  1. Remove the delivery pipe spacers.



    A087158
  1. Using a screwdriver, pry out the 4 spacers from the cylinder head.



14. REMOVE FUEL INJECTOR ASSEMBLY


    A087157E01
  1. Pull out the 4 injectors from the delivery pipe.

  1. Remove the O-rings from the injectors.



15. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY (for Automatic Transmission)


    C102934E01
  1. Remove the 2 bolts transmission oil filler tube sub-assembly.

  1. Remove the O-ring from the oil filler tube sub-assembly.



16. REMOVE INTAKE MANIFOLD
  1. Disconnect the vacuum hose and connector from the VSV.



    A110725
  1. Disconnect the 2 wire harness clamps.

  1. Disconnect the ventilation hose No.3 from the intake manifold.

  1. Loosen the 2 clips and disconnect the brake booster hose and the fuel vapor feed hose from the intake manifold.



    A110726
  1. Remove the bolt and the wire harness bracket from the intake manifold.



    G037711
  1. Remove the 5 bolts, 2 nuts, and intake manifold.

  1. Remove the gasket from the intake manifold.



17. REMOVE E.F.I. ENGINE COOLANT TEMPERATURE SENSOR
  1. Disconnect the engine coolant temperature sensor connector.



    A102134
  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.