Home › RESTRAINTS › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY

REAR SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL NO.4 SEAT BELT ASSEMBLY OUTER


    B107675
  1. Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.



    B107674
  1. Install the No.4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107673
  1. Engage the 4 claws to install the retractor cover of the No.4 seat belt assembly outer.



    B107672
  1. Connect the shoulder side of the No.4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107671
  1. Engage the 2 claws to install the shoulder side cover of the No.4 seat belt assembly outer.



    B107670
  1. Connect the floor side of the No.4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the outer belt assembly.



2. INSTALL NO.3 SEAT BELT ASSEMBLY OUTER


    B107669
  1. Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.



    B107668
  1. Install the No.3 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107667
  1. Engage the 4 claws to install the retractor cover of the No.3 seat belt assembly outer.



    B107666
  1. Connect the shoulder side of the No.3 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107665
  1. Engage the 4 claws to install the retractor cover of the No.3 seat belt assembly outer.



    B107664
  1. Connect the floor side of the No.3 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the outer belt assembly.



3. INSTALL REAR NO.2 SEAT BELT ASSEMBLY OUTER


    B113927
  1. Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.



    B105617
  1. Install the rear No.2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B105616
  1. Connect the shoulder side of the rear No.2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B105615
  1. Engage the 2 claws to install the retractor cover of the rear No.2 seat belt assembly outer.



    B105614
  1. Connect the floor side of the rear No.2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the outer belt assembly.



4. INSTALL REAR SEAT BELT ASSEMBLY OUTER


    B107663
  1. Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.



    B107662
  1. Install the rear seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107661
  1. Connect the shoulder side of the rear seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B107660
  1. Engage the 4 claws to install the retractor cover of the rear seat belt assembly outer.



    B107659
  1. Connect the floor side of the rear seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the outer belt assembly.



5. INSTALL REAR SEAT 3-POINT TYPE BELT ASSEMBLY (for Rear No.4 Seat Assembly)


    B105634
  1. Install the rear seat 3 point type belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the 3 screws.



6. INSTALL REAR SEAT SHOULDER BELT HOLE COVER (for Rear No.4 Seat Assembly)


7. INSTALL REAR SEAT CUSHION SHIELD INNER NO.1 (for Rear No.4 Seat Assembly)


8. INSTALL NO.4 SEATBACK COVER SUB-ASSEMBLY WITH PAD (for Rear No.4 Seat Assembly)


9. INSTALL REAR SEATBACK LOCK BEZEL LOWER (for Rear No.4 Seat Assembly)


10. INSTALL REAR SEATBACK LOCK BEZEL UPPER (for Rear No.4 Seat Assembly)


11. INSTALL REAR SEAT HEADREST SUPPORT (for Rear No.4 Seat Assembly)


12. INSTALL REAR SEAT HEADREST SUPPORT (for Rear No.4 Seat Assembly)


13. INSTALL REAR SEAT CUSHION (for Rear No.4 Seat Assembly)


14. INSTALL REAR SEAT HEADREST ASSEMBLY (for Rear No.4 Seat Assembly)


15. INSTALL NO.4 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD (for Rear No.4 Seat Assembly)


    B107631
  1. Install the No.4 seat cushion cover sub-assembly with pad with the hook and 2 clips.



    B107630
  1. Install the No.4 seat cushion assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



16. CONNECT REAR SEAT 3-POINT TYPE BELT ASSEMBLY (for Rear No.4 Seat Assembly)
  1. Connect the rear seat 3-point type belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



17. INSTALL LAP BELT OUTER ANCHOR COVER (for Rear No.4 Seat Assembly)


18. INSTALL RECLINING ADJUSTER COVER RH (for Rear No.4 Seat Assembly)


19. INSTALL RECLINING ADJUSTER COVER LH (for Rear No.4 Seat Assembly)


20. INSTALL RECLINING ADJUSTER RELEASE HANDLE (for Rear No.4 Seat Assembly)


21. INSTALL NO.4 SEAT LEG BRACKET REAR (for Rear No.4 Seat Assembly)


    B107626
  1. Install the No.4 seat leg bracket rear with the bolt and spacer.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



22. INSTALL REAR SEAT 3-POINT TYPE BELT ASSEMBLY (for Rear No.2 Seat Assembly)


    B105623
  1. Install the rear seat 3 point type belt assembly with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the 4 screws.



23. INSTALL REAR SEAT 3-POINT TYPE BELT ASSEMBLY (for Rear No.3 Seat Assembly)


    B105630
  1. Install the 2 rear seat 3 point type belt assemblies with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the 8 screws.



24. INSTALL NO.2 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD (for Rear No.2 Seat Assembly)


25. INSTALL NO.3 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD (for Rear No.3 Seat Assembly)


26. INSTALL RECLINING ADJUSTER COVER LH (for Rear No.2 Seat Assembly)


27. INSTALL RECLINING ADJUSTER COVER LH (for Rear No.3 Seat Assembly)


28. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.2 LH (for Rear No.2 Seat Assembly)


29. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.3 LH (for Rear No.3 Seat Assembly)


30. INSTALL REAR SEAT BELT ASSEMBLY INNER (for Rear No.2 Seat Assembly)


    B107678
  1. Install the rear seat belt assembly inner with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



31. INSTALL REAR SEAT BELT ASSEMBLY INNER (for Rear No.3 Seat Assembly)

HINT:
Follow the same procedure as for the rear No.2 seat assembly.



32. INSTALL RECLINING ADJUSTER COVER RH (for Rear No.2 Seat Assembly)


33. INSTALL RECLINING ADJUSTER COVER RH (for Rear No.3 Seat Assembly)


34. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.2 RH (for Rear No.2 Seat Assembly)


35. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.3 RH (for Rear No.3 Seat Assembly)


36. INSTALL REAR SEAT BELT ASSEMBLY OUTER (for Swiveling Seat Type)
  1. Install the rear seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



37. INSTALL REAR SEAT TURN TABLE COVER (for Swiveling Seat Type)


38. INSTALL SEAT TRACK ADJUSTING HANDLE KNOB (for Swiveling Seat Type)


39. INSTALL RECLINING ADJUSTER COVER RH (for Swiveling Seat Type)


40. INSTALL RECLINING ADJUSTER COVER LH (for Swiveling Seat Type)


41. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.1 (for Swiveling Seat Type)


42. INSTALL REAR NO.4 SEAT ASSEMBLY


    B115899
  1. Secure the rear No.4 seat assembly with the 2 locks

  1. Install the rear No.4 seat assembly with the 3 bolts and 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    After installing the rear No.4 seat assembly, fold down the seatback onto the seat cushion, lift the side of the rear No.4 seat assembly, and drop it to engage the locks securely.



43. INSTALL REAR NO.3 SEAT ASSEMBLY
w/o Headrest
w/ Headrest


44. INSTALL REAR NO.2 SEAT ASSEMBLY
w/o Headrest
w/ Headrest


45. INSTALL REAR NO.1 SEAT ASSEMBLY
w/o Headrest
w/ Headrest