ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
| 2. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove the 9 bolts, nut, cylinder head cover, and gasket.
| 3. REMOVE CAMSHAFT TIMING PULLEY |
Set the No.1 cylinder to approx. 90° BTDC/compression.
![]() |
Using the crankshaft pulley bolt, turn the crankshaft 90°counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.
![]() |
Using SST, loosen the pulley bolt.
![]() |
Using SST, separate the timing pulley from the camshaft.
Remove the pulley bolt and timing pulley.
Remove the timing gear woodruff key.
| 4. REMOVE TIMING BELT NO.2 COVER |
Remove the 4 bolts and timing belt cover.
| 5. REMOVE CAMSHAFT OIL SEAL RETAINER |
Remove the 4 bolts, retainer and gasket.
| 6. REMOVE OIL SEAL RETAINER NO.2 OIL SEAL |
![]() |
Using a screwdriver and hammer, tap out the oil seal.
| 7. REMOVE CAMSHAFT |
![]() |
Turn the camshaft with a wrench so that the key groove faces upward.
![]() |
Uniformly loosen and remove the 10 bearing cap bolts, in several steps, in the sequence shown.
Remove the 5 bearing caps and camshaft.
Remove the 10 bearings from the bearing caps and cylinder head.
| 8. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Uniformly loosen and remove the 18 cylinder head bolts, in several steps, in the sequence shown.
![]() |
Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.
| 9. REMOVE CYLINDER HEAD GASKET |
Remove the cylinder gasket from the cylinder head.
| 10. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.1 |
![]() |
Remove the 2 bolts (A and B).
Loosen the bolt (C), and remove the timing belt idler No.1.
| 11. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.2 |
Remove the bolt, timing belt idler No.2 and spacer.
| 12. INSPECT TIMING BELT IDLER SUB-ASSEMBLY NO.1 |
![]() |
Visually check the seal portion of the timing belt idler No.1 for oil leakage.
If leakage is found, replace the timing belt idler No.1.
Check that the timing belt idler No.1 turns smoothly.
If necessary, replace the timing belt idler No.1.
| 13. INSPECT TIMING BELT IDLER SUB-ASSEMBLY NO.2 |
Check that the timing belt idler No.2 turns smoothly.
If necessary, replace the timing belt idler No.2.
| 14. INSPECT IDLER TENSION SPRING |
![]() |
Measure the free length of the tension spring.
Measure the tension of the tension spring at the specified installed length.
| 15. REMOVE WATER PUMP ASSEMBLY |
Remove the 6 bolts, tension spring bracket, water pump and gasket.
| 16. REMOVE CRANKSHAFT TIMING PULLEY |
![]() |
If the timing pulley cannot be removed by a screwdriver, remove it with SST.
| 17. REMOVE OIL PAN SUB-ASSEMBLY |
Remove the 16 bolts and 2 nuts.
![]() |
Insert the blade of SST between the oil pan and cylinder block, and cut off applied sealer and remove the oil pan.
| 18. REMOVE OIL STRAINER SUB-ASSEMBLY |
Remove the 2 bolts, 2 nuts, oil strainer and gasket.
| 19. REMOVE TIMING GEAR CASE SUB-ASSEMBLY |
Remove the 5 bolts, timing gear case and gasket.
| 20. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL |
![]() |
Using a screwdriver and hammer, tap out the oil seal.
| 21. REMOVE ENGINE REAR OIL SEAL RETAINER |
Remove the 4 bolts, oil seal retainer and gasket.
| 22. REMOVE ENGINE REAR OIL SEAL |
![]() |
Using a screwdriver and hammer, tap out the oil seal.
| 23. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using vernier calipers, measure the minimum outer diameter of the compressed thread at the measuring point.
| 24. REMOVE VALVE LIFTER |
Remove the valve lifter and adjusting shim.
| 25. REMOVE INTAKE VALVE |
![]() |
Using SST, compress the valve spring and remove the 2 retainer locks.
Remove the spring retainer, valve spring, valve and spring seat.
| 26. REMOVE EXHAUST VALVE |
![]() |
Using SST, compress the valve spring and remove the 2 retainer locks.
Remove the spring retainer, valve spring, valve and spring seat.
| 27. REMOVE VALVE STEM OIL SEAL |
![]() |
Using needle-nose pliers, remove the oil seal.
| 28. REMOVE COMBUSTION CHAMBER SUB-ASSEMBLY |
![]() |
Using SST, remove the 4 combustion chambers (and shims).
| 29. CLEAN CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a gasket scraper, remove all the gasket material from the cylinder block contact surface.
![]() |
Using a wire brush, remove all the carbon from the combustion chambers.
![]() |
Using a valve guide bushing brush and solvent, clean all the guide bushes.
![]() |
Using a soft brush and solvent, thoroughly clean the cylinder head.
| 30. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
Inspect for warpage.
![]() |
Using a precision straight edge and feeler gauge, measure the surfaces contacting the cylinder block and the manifolds for warpage.
Inspect for cracks.
![]() |
Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.
If cracked, replace the cylinder head.
| 31. CLEAN INTAKE VALVE |
![]() |
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
| 32. INSPECT INTAKE VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Check the valve face angle.
Grind the valve enough to remove pits and carbon.
Check that the valve is ground to the correct valve face angle.
![]() |
Check the valve head margin thickness.
![]() |
Check the valve overall length.
![]() |
Check the surface of the valve stem tip for wear.
| 33. CLEAN EXHAUST VALVE |
![]() |
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
| 34. INSPECT EXHAUST VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Check the valve face angle.
Grind the valve enough to remove pits and carbon.
Check that the valve is ground to the correct valve face angle.
Check the valve head margin thickness.
![]() |
Check the valve overall length.
![]() |
Check the surface of the valve stem tip for wear.
| 35. INSPECT INNER COMPRESSION SPRING |
![]() |
Using a steel square, measure the deviation of the spring.
![]() |
Using vernier calipers, measure the free length of the spring.
| Type | Length |
| Type A | 46.20 mm (1.8189 in.) |
| Type B | 48.54 mm (1.9110 in.) |
Using a spring tester, measure the tension of the valve spring at the specified installed length.
| 36. INSPECT INTAKE VALVE GUIDE BUSH |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement (See step 32) from the guide bush inside diameter measurement.
| 37. INSPECT EXHAUST VALVE GUIDE BUSH |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement (See step 34) from the guide bush inside diameter measurement.
| 38. REMOVE INTAKE VALVE GUIDE BUSH |
![]() |
Using SST and a hammer, tap out the valve guide bushing.
| 39. REMOVE EXHAUST VALVE GUIDE BUSH |
![]() |
Using SST and a hammer, tap out the valve guide bushing.
| 40. INSTALL INTAKE VALVE GUIDE BUSH |
Using a caliper gauge, measure the bush bore diameter of the cylinder head.
Select a new guide bush (STD or O/S 0.05).
| Bush bore diameter | Bush size |
| 13.004 to 13.025 mm (0.5120 to 0.5128 in.) | Use STD |
| 13.054 to 13.075 mm (0.5139 to 0.5148 in.) | Use O/S 0.05 |
![]() |
Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
![]() |
Using a sharp 8.0 mm reamer, ream the guide bush to obtain the standard specified clearance (See step 36) between the guide bush and valve stem.
| 41. INSTALL EXHAUST VALVE GUIDE BUSH |
![]() |
Using a caliper gauge, measure the bush bore diameter of the cylinder head.
Select a new guide bush (STD or O/S 0.05).
| Bush bore diameter | Bush size |
| 13.004 to 13.025 mm (0.5120 to 0.5128 in.) | Use STD |
| 13.054 to 13.075 mm (0.5139 to 0.5148 in.) | Use O/S 0.05 |
![]() |
Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
![]() |
Using a sharp 8.0 mm reamer, ream the guide bush to obtain the standard specified clearance (See step 37) between the guide bush and valve stem.
| 42. INSPECT INTAKE VALVE SEATS |
![]() |
Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the seats.
![]() |
Check the valve seating position.
Apply a light coat of prussian blue (or white lead) to the valve face.
Lightly press the valve against the seat. Do not rotate valve.
Check the valve face and seat by using the following procedure:
If prussian blue appears around the entire valve face, the valve is concentric. If not, replace the valve.
If prussian blue appears around the entire valve seat, the guide and face are concentric. If not, resurface the seat.
Check that the seat contacts in the middle of the valve face with the following width:
| 43. INSPECT EXHAUST VALVE SEATS |
![]() |
Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the seats.
![]() |
Check the valve seating position.
Apply a light coat of prussian blue (or white lead) to the valve face.
Lightly press the valve against the seat. Do not rotate valve.
Check the valve face and seat by using the following procedure:
If prussian blue appears around the entire valve face, the valve is concentric. If not, replace the valve.
If prussian blue appears around the entire valve seat, the guide and face are concentric. If not, resurface the seat.
Check that the seat contacts in the middle of the valve face with the following width:
| 44. REPAIR INTAKE VALVE SEATS |
![]() |
If the seating is too high on the valve face, use 30° and 45° cutters to correct the seat.
![]() |
If the seating is too low on the valve face, use 60° and 45° cutters to correct the seat.
![]() |
Handrub the valve and valve seat with an abrasive compound.
After handrubbing, clean the valve and valve seat.
| 45. REPAIR EXHAUST VALVE SEATS |
![]() |
If the seating is too high on the valve face, use 30° and 45° cutters to correct the seat.
![]() |
If the seating is too low on the valve face, use 60° and 45° cutters to correct the seat.
![]() |
Handrub the valve and valve seat with an abrasive compound.
After handrubbing, clean the valve and valve seat.
| 46. INSPECT VALVE LIFTER |
![]() |
Using a micrometer, measure the lifter diameter.
![]() |
Using a caliper gauge, measure the lifter bore diameter of the cylinder head.
Subtract the lifter diameter measurement from the lifter bore diameter measurement.
| 47. INSPECT CAMSHAFT |
Inspect the circle runout.
Place the camshaft on V-blocks.
![]() |
Using a dial indicator, measure the circle runout at the center journal.
Using a micrometer, measure the cam lobe height.
| Cam lobe height | |
| Intake | 54.890 to 54.910 mm (2.1610 to 2.1618 in.) |
| Exhaust | 54.990 to 55.010 mm (2.1650 to 2.1657 in.) |
| Cam lobe height | |
| Intake | 54.39 mm (2.1413 in.) |
| Exhaust | 54.49 mm (2.1453 in.) |
Inspect the journal diameter of the camshaft.
Using a micrometer, measure the journal diameter of the camshaft for the camshaft bearing.
| Journal | Diameter | |
| STD | No.1 | 34.969 to 34.985 mm (1.3767 to 1.3774 in.) |
| Other | 27.969 to 27.985 mm (1.1011 to 1.1018 in.) | |
| U/S 0.125 | No.1 | 34.844 to 34.860 mm (1.3718 to 1.3724 in.) |
| Other | 27.844 to 27.860 mm (1.0962 to 1.0968 in.) | |
| U/S 0.250 | No.1 | 34.719 to 34.735 mm (1.3669 to 1.3675 in.) |
| Other | 27.719 to 27.735 mm (1.0913 to 1.0919 in.) |
![]() |
Check the oil clearance.
Clean the bearing caps and journals.
Check the bearings for flaking and scoring.
If the bearings are damaged, replace them.
Install the bearings to the bearing caps and cylinder head.
Place the camshaft on the cylinder head.
Lay a strip of Plastigage across each of the journals.
Install the bearing caps (See reassembly, step 37).
Remove the bearing caps (See step 7).
![]() |
Measure the Plastigage at its widest point.
Completely remove the Plastigage.
Remove the camshaft.
If necessary, grind and hone the camshaft journals.
Grind and hone the journals to U/S diameter (See procedure (c) above). Install new journal U/S bearings.
Check the thrust clearance.
Install the camshaft (See reassembly, step 37).
![]() |
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 48. REMOVE SEMICIRCULAR PLUG |
Remove the semicircular plug from the cylinder head.
| 49. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 50. INSPECT CONNECTING ROD OIL CLEARANCE |
![]() |
Check the matchmarks on the connecting rod and cap to ensure correct reassembly.
Remove the 2 connecting rod cap nuts.
![]() |
Using a plastic hammer, lightly tap the connecting rod bolts and lift off the connecting rod cap.
![]() |
Cover the connecting rod bolts with a short piece of hose to protect the crankshaft from damage.
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches.
If the crank pin or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
![]() |
Lay a strip of Plastigage across the crank pin.
![]() |
Install the connecting rod cap with the 2 nuts (See reassembly, step 15).
Remove the 2 nuts, connecting rod cap and lower bearing (See procedure (b) and (c) above).
![]() |
Measure the Plastigage at its widest point.
| Size | Oil clearance |
| STD | 0.036 to 0.064 mm (0.0014 to 0.0025 in.) |
| U/S 0.25 U/S 0.50 | 0.033 to 0.079 mm (0.0013 to 0.0031 in.) |
![]() |
If using a standard bearing, replace it with one having the same number marked on the connecting rod cap. There are 3 sizes of standard bearings, marked 1, 2 and 3 accordingly.
| Mark | Center wall thickness |
| 1 | 1.478 to 1.482 mm (0.0582 to 0.0583 in.) |
| 2 | 1.482 to 1.486 mm (0.0583 to 0.0585 in.) |
| 3 | 1.486 to 1.490 mm (0.0585 to 0.0587 in.) |
Completely remove the Plastigage.
| 51. REMOVE PISTON AND CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
![]() |
Cover the connecting rod bolts with a short piece of hose to protect the crankshaft from damage.
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.
| 52. REMOVE PISTON SUB-ASSEMBLY W/PIN |
Check the fitting condition between the piston and piston pin.
![]() |
Try to move the piston back and forth on the piston pin.
If any movement is felt, replace the piston and pin as a set.
Remove the piston rings.
![]() |
Using a piston ring expander, remove the 2 compression rings.
Remove the oil ring and coil by hand.
Disconnect the connecting rod from the piston.
![]() |
Using snap ring pliers, remove the snap rings.
![]() |
Gradually heat the piston to approx. 60°C (140°F).
![]() |
Using a plastic hammer and brass bar, lightly tap out the piston pin and pin and remove the connecting rod.
| 53. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| Size | Thickness |
| STD | 2.430 to 2.480 mm (0.0957 to 0.0976 in.) |
| O/S 0.125 | 2.493 to 2.543 mm (0.0981 to 0.1001 in.) |
| O/S 0.250 | 2.555 to 2.605 mm (0.1006 to 0.1026 in.) |
| 54. INSPECT CRANKSHAFT OIL CLEARANCE |
![]() |
Remove the 10 crankshaft bearing cap bolts.
![]() |
Using the removed crankshaft bearing cap bolts, pry the cap back and forth, and remove the crankshaft bearing caps, lower bearings and lower thrust washers (No.3 crankshaft bearing cap only).
Lift out the crankshaft.
Clean each main journal and bearing.
Check each main journal and bearing for pitting and scratches.
If the journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
![]() |
Install the 5 crankshaft bearing caps with the 10 bolts (See reassembly, step 14).
Remove the 10 bolts and 5 crankshaft bearing caps (See procedure (a) and (b) above).
![]() |
Measure the Plastigage at its widest point.
| Size | Oil clearance |
| STD | 0.034 to 0.065 mm (0.0013 to 0.0026 in.) |
| U/S 0.25, U/S 0.50 | 0.033 to 0.079 mm (0.0013 to 0.0031 in.) |
![]() |
If using a standard bearing, replace it with one having the same number marked on the connecting rod cap. There are 3 sizes of standard bearings, marked 1, 2 and 3 accordingly.
| Mark | Center wall thickness |
| 1 | 1.979 to 1.983 mm (0.0779 to 0.0781 in.) |
| 2 | 1.983 to 1.987 mm (0.0781 to 0.0782 in.) |
| 3 | 1.987 to 1.991 mm (0.0782 to 0.0784 in.) |
Completely remove the Plastigage.
| 55. REMOVE CRANKSHAFT |
Lift out the crankshaft.
Remove the upper bearings and upper thrust washers from the cylinder block.
| 56. REMOVE OIL NOZZLE NO.1 SUB-ASSEMBLY |
Remove the 4 check valves and oil nozzles.
| 57. INSPECT OIL CHECK VALVE SUB-ASSEMBLY |
![]() |
Push the valve with a wooden stick to check if it is stuck.
If stuck, replace the check valve.
| 58. INSPECT OIL NOZZLE NO.1 SUB-ASSEMBLY |
Check the oil nozzles for damage or clogging.
If necessary, replace the oil nozzle.
| 59. REMOVE CYLINDER BLOCK OIL ORIFICE |
Using a 6 mm hexagon wrench, remove the oil orifice.
| 60. INSPECT CYLINDER BLOCK OIL ORIFICE |
Check the oil orifice for damage or clogging.
If necessary, replace the oil orifice.
| 61. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
Remove the water drain cock from the cylinder block.
| 62. REMOVE W/HEAD TAPER SCREW PLUG NO.1 |
Remove the screw plug from the cylinder block.
| 63. CLEAN CYLINDER BLOCK SUB-ASSEMBLY |
![]() |
Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.
Using a soft brush and solvent, thoroughly clean the cylinder block.
| 64. INSPECT CYLINDER BLOCK SUB-ASSEMBLY |
Inspect for warpage.
![]() |
Using a precision straight edge and feeler gauge, measure the surface contacting the cylinder head cap for warpage.
![]() |
Visually check the cylinder for vertical scratches.
If deep scratches are present, rebore all the 4 cylinders. If necessary, replace the cylinder block.
![]() |
Inspect the cylinder bore diameter.
![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions A, B and C in the thrust and axial directions.
| Mark | Diameter |
| 1 | 99.500 to 99.510 mm (3.9173 to 3.9177 in.) |
| 2 | 99.510 to 99.520 mm (3.9177 to 3.9181 in.) |
| 3 | 99.520 to 99.530 mm (3.9181 to 3.9185 in.) |
| Diameter | |
| STD | 99.73 mm (3.9264 in.) |
| O/S 0.50 | 100.23 mm (3.9461 in.) |
![]() |
Remove the cylinder ridge.
If the wear is less than 0.2 mm (0.008 in.), using a ridge reamer, grind the top of the cylinder.
| 65. CLEAN PISTON SUB-ASSEMBLY W/PIN |
![]() |
Using a gasket scraper, remove the carbon from the piston top.
![]() |
Using a groove cleaning tool or broken ring, clean the piston ring grooves.
![]() |
Using solvent and a brush, thoroughly clean the piston.
| 66. INSPECT PISTON SUB-ASSEMBLY W/PIN |
Inspect the piston oil clearance.
![]() |
Using a micrometer, measure the piston diameter at right angles to the piston center line where the distance from the piston head is as specified.
| Size | Diameter |
| STD Mark 1 | 99.450 to 99.460 mm (3.9153 to 3.9157 in.) |
| STD Mark 2 | 99.460 to 99.470 mm (3.9157 to 3.9161 in.) |
| STD Mark 3 | 99.470 to 99.480 mm (3.9161 to 3.9165 in.) |
| O/S 0.50 | 99.950 to 99.980 mm (3.9350 to 3.9362 in.) |
Measure the cylinder bore diameter in the thrust direction (See step 64).
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
![]() |
Use a piston with the same number mark as the cylinder bore diameter marked on the cylinder block.
Inspect the piston pin fitting condition.
![]() |
Check that the piston pin is pushed into the piston pin hole with your thumb at 60°C (140°F).
If the pin can be installed at a lower temperature, replace the piston and pin as a set.
![]() |
Using a micrometer, measure the piston pin diameter.
| 67. INSPECT PISTON RING SET |
Inspect the piston ring groove clearance.
![]() |
No. 1 Ring: Install a new piston ring to the piston. Using a feeler gauge, measure the clearance between the piston ring and the wall of the ring groove.
![]() |
No. 2 and Oil Rings: Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
| Ring | Groove clearance |
| No. 2 | 0.060 to 0.100 mm (0.0024 to 0.0039 in.) |
| Oil | 0.030 to 0.070 mm (0.0012 to 0.0028 in.) |
Inspect the piston ring end gap.
![]() |
Insert the piston ring into the cylinder bore.
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 140 mm (5.51 in.) from the top of the cylinder block.
![]() |
Using a feeler gauge, measure the end gap.
| Ring | End gap |
| No. 1 | 0.350 to 0.590 mm (0.0138 to 0.0232 in.) |
| No. 2 | 0.470 to 0.720 mm (0.0185 to 0.0283 in.) |
| Oil | 0.200 to 0.520 mm (0.0079 to 0.0205 in.) |
| Ring | End gap |
| No. 1 | 1.29 mm (0.0508 in.) |
| No. 2 | 1.42 mm (0.0559 in.) |
| No. 3 | 1.22 mm (0.0480 in.) |
| 68. INSPECT CONNECTING ROD SUB-ASSEMBLY |
Using a rod aligner and feeler gauge, check the connecting rod alignment.
![]() |
Check for bend.
![]() |
Check for twist
| 69. INSPECT PISTON PIN OIL CLEARANCE |
Inspect the piston pin oil clearance.
![]() |
Using a caliper gauge, measure the inside diameter of the connecting rod bush.
Subtract the piston pin diameter measurement (See step 66) from the bush inside diameter measurement.
| 70. REMOVE CONNECTING ROD SMALL END BUSH |
![]() |
Using SST and a press, press out the bush.
| 71. INSPECT CONNECTING ROD BOLT |
![]() |
Using vernier calipers, measure the tension portion of the connecting rod bolt.
| 72. BORE CYLINDER |
![]() |
Prepare 4 new O/S pistons.
Using a micrometer, measure the piston diameter at right angles to the piston pin center line where the distance from the piston head is as specified.
Calculate the amount each cylinder is to be rebored as follows:
Bore and hone the cylinders to the calculated dimensions.
| 73. INSPECT CRANKSHAFT |
Inspect for circle runout.
Place the crankshaft on V-blocks.
![]() |
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Inspect the main journals and crank pins.
Using a micrometer, measure the diameter of each main journal and crank pin.
| Size | Diameter |
| STD | 61.985 to 62.000 mm (2.4403 to 2.4409 in.) |
| U/S 0.25 | 61.745 to 61.755 mm (2.4309 to 2.4313 in.) |
| U/S 0.50 | 61.495 to 61.505 mm (2.4211 to 2.4215 in.) |
| Size | Diameter |
| STD | 54.988 to 55.000 mm (2.1649 to 2.1654 in.) |
| U/S 0.25 | 54.745 to 54.755 mm (2.1553 to 2.1557 in.) |
| U/S 0.50 | 54.495 to 54.505 mm (2.1455 to 2.1459 in.) |
Check each main journal and crank pin for taper and out-of-round as shown.
If necessary, grind and hone the main journals and/or crank pins.
Grind and hone the main journals and/or crank pins to the finished undersized diameter (See procedure in step (b) above).
Install new main journal and/or crankshaft pin undersized bearing.