Home › ENGINE · 2TR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL TIGHT PLUG

NOTICE:
If water leaks from the tight plug or the plug corrodes, replace it.



    A058129E01
  1. Apply adhesive around the tight plugs.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent.

  1. Using SST and a hammer, tap in new tight plugs as shown in the illustration.

  1. Using SST, tap in the 8 tight plugs A and C.

    SST
    09950-60010   (09951-00350)
    09950-70010   (09951-07100)

  1. Using SST, tap in the tight plug B.

    SST
    09950-60010   (09951-00300)
    09950-70010   (09951-07100)



  1. Using SST, tap in the 3 tight plugs D.


    A103432E02

    SST
    09950-60010   (09951-00400)
    09950-70010   (09951-07100)



2. INSTALL STUD BOLT
  1. Using an E8 "torx" socket wrench, install the stud bolts A.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

  1. Using an E7 "torx" socket wrench, install the stud bolts B and D.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }



  1. Apply adhesive to the hole for the stud bolt C on the cylinder block. Using an E7 "torx" socket wrench, install the stud bolts C.


    G037383E05

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    NOTICE:
    If the stud bolt is deformed or the threads are damaged, replace it.



3. INSTALL STRAIGHT PIN


    A101513E02
  1. Using a plastic hammer, tap in new straight pins to the cylinder block.



4. INSTALL RING PIN


  1. Using a plastic hammer, tap in new ring pins to the cylinder block.


    A101514E02



5. INSTALL BALANCESHAFT DRIVEN GEAR NO.2
  1. Mount the head portion of the balanceshaft in a vise.

    NOTICE:
    Do not damage the balanceshaft.



    A101523E02
  1. Install the balanceshaft thrust washer No.2 (● 1) and balanceshaft driven gear No.2 (● 2).

  1. Install and torque the bolt.

    Torque:
    36 N*m{ 365 kgf*cm , 26 ft.*lbf }



6. INSTALL NO.2 BALANCESHAFT


    A101522
  1. Install the balanceshaft to the cylinder block.

    NOTICE:
    When installing the balanceshaft, make sure to support the balanceshaft with both hands and avoid scratching the balanceshaft bearing on the cylinder block side.



    A101521
  1. Install and torque the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



7. INSTALL BALANCESHAFT DRIVEN GEAR NO.1
  1. Mount the head portion of the balanceshaft in a vise.

    NOTICE:
    Do not damage the balanceshaft.



    A101520E02
  1. Install the balanceshaft thrust spacer (● 4), balanceshaft thrust washer No.1 (● 3), sliding key (● 2) and balanceshaft driven gear No.1 (● 1).

  1. Install and torque the bolt.

    Torque:
    36 N*m{ 365 kgf*cm , 26 ft.*lbf }



8. INSTALL NO.1 BALANCESHAFT


    A101519
  1. Install the No.1 balanceshaft to the cylinder block.

    NOTICE:
    When installing the balanceshaft, make sure to support the balanceshaft with both hands and avoid scratching the balanceshaft bearing on the cylinder block side.



    A101518
  1. Install and torque the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



9. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


    A101346E01
  1. Apply adhesive around the drain cock.



    A101347E02
  1. Install the cylinder block water drain cock as shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Install the water drain cock plug to the water drain cock sub-assembly.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



10. INSTALL OIL NOZZLE NO.1 SUB-ASSEMBLY


    A101486E01
  1. Using an E7 "torx" socket wrench, install the oil nozzles.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



11. INSTALL CONNECTING ROD SMALL END BUSH


    A054732E01
  1. Align the oil holes of a new bush and the connecting rod.



    A054717E01
  1. Using SST and a press, press in the bush.

    SST
    09222-30010  



    A054733
  1. Using a pin hole grinder, hone the bush to obtain the standard specified clearance (See disassembly, step 107) between the bush and piston pin.



  1. Check that the piston pin fits at normal room temperature.



      A054734
    1. Coat the piston pin with engine oil, and push it into the connecting rod with your thumb.



12. INSTALL W/PIN PISTON SUB-ASSEMBLY


  1. Assemble the piston and connecting rod.



      A103205E03
    1. Using a screwdriver, install a new snap ring at one end of the piston pin hole.



    2. A101484E02
    3. Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

    4. Coat the piston pin with engine oil.



    5. A101516E01
    6. Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.

      HINT:
      The piston and pin are a matched set.



    7. G035197
    8. Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.



    9. A101515E04
    10. Using a screwdriver, install a new snap ring at the other end of the piston pin hole.



13. INSTALL PISTON RING SET
  1. Install the oil ring expander by hand.



    A101483
  1. Using a piston ring expander, install the oil ring rail.



    G038405E01
  1. Using a piston ring expander, install the 2 compression rings so that the painted marks are positioned as shown in the illustration.

    HINT:
    1. Install the compression ring No.1 with the code mark (1N) facing upward.
    2. Install the compression ring No.2 with the code mark (2N) facing upward.



    A101531E02
  1. Position the piston rings so that the ring ends are as shown in the illustration.

    NOTICE:
    Do not align the ring ends.



14. INSTALL CRANKSHAFT BEARING

NOTICE:
  1. Do not apply engine oil to the bearing's contact area and backside.
  2. The crankshaft bearing cap bolt is tightened in 2 progressive steps.

  1. Clean the main journal, and the both surfaces of the bearing.



  1. Install the upper bearing.



      A101500E01
    1. Install the upper bearing to the cylinder block as shown in the illustration.
      Journal
      Dimension
      # 1, 5
      3.75 mm (0.1476 in.)
      # 3
      1.75 mm (0.0689 in.)
      # 2, 4
      2.75 mm (0.1083 in.)

      NOTICE:
      Do not apply engine oil to the bearing's contact area and backside.



  1. Install the lower bearing.

    1. Install the lower bearing to the bearing cap.



    2. A101501E01
    3. Using vernier calipers, measure the distance between the bearing cap's edge and the lower bearing's edge.

      Dimension (A - B):
      0.3 mm (0.0118 in.) or less

      Journal
      Dimension (A)
      # 1, 5
      3.83 mm (0.1508 in.)
      # 3
      1.74 mm (0.0685 in.)
      # 2, 4
      2.75 mm (0.1083 in.)

      NOTICE:
      Do not apply engine oil to the bearing's contact area and backside.

  1. With the upper bearing and lower bearing installed, use a plastic hammer to install the bearing caps to the cylinder block.

    NOTICE:
    Make sure that the bearing caps are installed in the correct positions and direction.



    A101502E01
  1. Using vernier calipers, measure the amount of misalignment between the upper bearing and lower bearing, as shown in the illustration.

    Standard:
    0.9 mm (0.035 in.) or less

  1. Remove the bearing cap.



  1. Install the crankshaft thrust washer upper to the cylinder block.



      A101503E01
    1. Install the 2 thrust washers under the No.3 journal position of the cylinder block with the oil grooves facing outward.

      NOTICE:
      Be careful when installing the thrust bearing upper and lower as they are similar but cannot be interchanged.



    A101504E01
  1. Install the 2 thrust washers on the No.3 bearing cap with the grooves facing outward.

    NOTICE:
    Be careful when installing the thrust bearing upper and lower as they are similar but cannot be interchanged. The bearing lower has a claw as shown in the illustration.

  1. Apply engine oil to the lower bearing.



15. INSTALL CRANKSHAFT
  1. Apply engine oil to the upper bearing, then place the crankshaft on the cylinder block.



    A101506
  1. Install the 5 crankshaft bearing caps in their proper locations.

  1. Install the crankshaft bearing cap bolts.

    HINT:
    The main bearing cap bolts are tightened in 2 progressive steps.



  1. Step 1



      A101507E01
    1. Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }

      If any of the main bearing cap bolts does not meet the torque specification, replace the main bearing cap bolt.



  1. Step 2

    1. Mark the front of the bearing cap bolts with paint.



    2. A101478E05
    3. Retighten the bearing cap bolts by 90° in the order above.

    4. Check that the painted mark is now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

  1. Check the crankshaft thrust clearance (See disassembly, step 86).



16. INSTALL CONNECTING ROD BEARING


    A101528E01
  1. Align the bearing claw with the groove of the connecting rod or connecting cap.

  1. Install the bearings in the connecting rod and connecting rod cap.

    NOTICE:
    Clean the backside of the bearing and the bearing surface of the connecting rod.



17. INSTALL PISTON SUB-ASSEMBLY W/CONNECTING ROD
  1. Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.



    A101531E02
  1. Position the piston rings so that the ring ends are as shown in the illustration.

    NOTICE:
    Do not align the ring ends.



    A101529E01
  1. Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.

  1. Match the numbered connecting rod cap with the connecting rod.

    NOTICE:
    Match the numbered connecting rod cap with the connecting rod.



    A101476E01
  1. Check that the front mark of the connecting rod cap is facing forward.

  1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.



    A101477
  1. Install and alternately tighten the bolts of the connecting rod cap in several steps.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



    A101478E05
  1. Mark the front side of each connecting cap bolt with paint.

  1. Retighten the cap bolts by 90° as shown.

  1. Check that the painted mark is now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

  1. Check the connecting rod thrust clearance (See disassembly, step 82).



18. INSTALL INTAKE VALVE GUIDE BUSH


    A101404
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057)

  1. Select a new guide bush (STD or O/S 0.05).
    Bush bore diameter
    Bush size
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    Use STD
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)
    Use O/S 0.05
    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install a O/S 0.05 valve guide bush.
    If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.



    A101401E05
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.



    A101405E01
  1. Using SST, tap in a new valve guide bush to the specified protrusion height.

    Protrusion height (A):
    9.8 to 10.2 mm (0.3858 to 0.4016 in.)

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)



    A101406
  1. Using a sharp 5.5 mm reamer, ream the valve guide bush to obtain the standard specified clearance.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0023 in.)



19. INSTALL EXHAUST VALVE GUIDE BUSH


    A101407
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

  1. Select a new guide bush (STD or O/S 0.05)
    Bush bore diameter
    Bush size
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    Use STD
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)
    Use O/S 0.05
    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install a O/S 0.05 valve guide bush.
    If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.



    A101401E05
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.



    A101408E01
  1. Using SST, tap in a new valve guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    (A)
    7.6 to 8.0 mm (0.2992 to 0.3150 in.)



    A101409
  1. Using a sharp 5.5 mm reamer, ream the valve guide bushing to obtain the standard specified clearance.

    Standard oil clearance:
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)



20. INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:
It is not necessary to remove w/ head pin unless it is being replaced.



    G037442E02
  1. Using a plastic hammer, tap in a new ring pin until the pin stops.



21. INSTALL TIGHT PLUG NO.1

NOTICE:
If water leaks from the tight plug or the plug corrodes, replace it.



    A058129
  1. Apply adhesive to the tight plug hole of the cylinder head.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent.



    A101411E01
  1. Using SST, tap in a new tight plug to the cylinder head as shown in the illustration

    SST
    09950-60010   (09951-00250)
    09950-70010   (09951-07100)



22. INSTALL STUD BOLT

NOTICE:
If the stud bolt is deformed or the threads are damaged, replace it.



  1. Using E6 and E7 "torx" socket wrenches, install the stud bolts.


    G037444E05

    Torque:
    for stud bolt A:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }
    for stud bolt B:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    for stud bolt C:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



23. INSTALL W/HEAD STRAIGHT SCREW PLUG NO.1


    A101373
  1. Using a 10 mm hexagon wrench, install 3 new gaskets and the straight screw plugs.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



24. INSTALL W/HEAD STRAIGHT SCREW PLUG NO.2


    A101374
  1. Using a 19 mm hexagon wrench, install a new gasket and the straight screw plug.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }



25. INSTALL OIL CONTROL VALVE FILTER


    A101413
  1. Check that no foreign matter is on the mesh part of the filter.
    If foreign objects are present, clean the part thoroughly.

  1. Using a 8 mm hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



26. INSTALL VALVE SPRING SEAT
  1. Install the valve spring seats to the cylinder head.



27. INSTALL VALVE STEM OIL SEAL


    A101414E01
  1. Apply a light coat of engine oil to new oil seals.

    NOTICE:
    Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust side or installing the exhaust oil seal to the intake side can cause installation problems later.

    HINT:
    The intake valve oil seals are white and the exhaust valve oil seals are black.



    A101415E01
  1. Using SST, push in the oil seals.

    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.



28. INSTALL INTAKE VALVE


    A101416E01
  1. Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.



    A101417
  1. Install the valve, compression spring and spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.



    A101369E01
  1. Using SST and wooden blocks, compress the spring and install the 2 retainer locks.

    SST
    09202-70020   (09202-00010)



    A101418E01
  1. Using a 5 mm pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Do not damage the valve stem tip.



29. INSTALL EXHAUST VALVE


    A101419E01
  1. Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.



    A101420
  1. Install the valve, compression spring and spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.



    A101370E01
  1. Using SST and wooden blocks, compress the spring and install the 2 retainer locks.

    SST
    09202-70020   (09202-00010)



    A101421E01
  1. Using a 5 mm pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Do not damage the valve stem tip.



30. INSTALL VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the lash adjuster free from dirt and foreign objects.
  2. Only use clean engine oil.



    A101354E02
  1. Place the lash adjuster into a container full of engine oil.

  1. Insert the SST's tip into the lash adjuster's plunger and use the tip to press down on the checkball inside the plunger.

    SST
    09276-75010  

  1. Squeeze the SST and lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed the air.

    OK:
    Plunger is very difficult to move.

  1. After bleeding the air, remove the SST. Then quickly and firmly press the plunger with a finger.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the lash adjuster.



    A101316
  1. Install the lash adjusters.

    NOTICE:
    Install the lash adjuster to the original position.



31. INSTALL VALVE STEM CAP


    A101315
  1. Apply a light coat of engine oil to the valve stem caps.

  1. Install the valve stem caps to the cylinder head.



32. INSTALL CRANKSHAFT PULLEY SET KEY


    A101326
  1. Install the 2 pulley keys to the crankshaft.



33. INSTALL CHAIN VIBRATION DAMPER NO.4


    A101325E01
  1. Install the vibration damper No.4 with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }



34. INSTALL NO.2 CHAIN SUB-ASSEMBLY


    A101978
  1. Install the timing sprocket No.2 as shown in the illustration.

    NOTICE:
    Check that the No.1 cylinder is at TDC and that the weights of the No.1 and No.2 balanceshafts are at the bottom side.

    HINT:
    Install the sensor plate with the front mark facing forward.



    A101339E01
  1. As shown in the illustration, install the chain on the sprocket and gear with the painted marks aligned with the timing marks on the sprocket and gear.



    A101340E02
  1. Fit the other mark link of the crankshaft timing sprocket behind the large timing mark of the balanceshaft drive gear.

  1. Insert the balanceshaft drive gear shaft through the balanceshaft drive gear so that it fits into the thrust plate hole.



    A101341E02
  1. Align the small timing mark of the balanceshaft drive gear with the timing mark of the balanceshaft timing gear.

  1. Install the bolt to the balanceshaft drive gear and tighten it.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    A101342E01
  1. Check that each timing mark is matched with the corresponding mark link.

    NOTICE:
    Check that the No.1 cylinder is at TDC and that the weights of the No.1 and No.2 balanceshafts are at the bottom side.



35. INSTALL CHAIN TENSIONER ASSEMBLY NO.2


    A101323E01
  1. Install the chain tensioner assembly No.2 with the nut.

    Torque:
    18 N*m{ 185 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Assemble the chain tensioner with the pin installed, then remove the pin after assembly. When doing this, do not push the vibration damper against the chain.



    A101320E02
  1. Move the stopper plate downward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate upward to set the lock, and insert a hexagon wrench into the stopper plate hole.



36. INSTALL CHAIN VIBRATION DAMPER NO.3


    A101322E01
  1. Install the chain vibration damper No.3 with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }



37. INSTALL CHAIN VIBRATION DAMPER NO.2


    A101321E01
  1. Install the chain vibration damper No.2 with the bolt.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }

  1. Remove the pin from the chain tensioner assembly No.2 and release the plunger.



38. INSTALL W/HEAD TAPER SCREW PLUG NO.1


    A101908E01
  1. Install the screw plug No.1 to the cylinder block.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



39. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY


    A101977E01
  1. Using a hexagon wrench, install the oil filter bracket union.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    G037305E01
  1. Install a new oil filter bracket gasket to the oil filter bracket.

  1. Install a new O-ring to the oil filter bracket union.

    NOTICE:
    Apply a light coat of engine oil to the new O-ring and oil filter bracket.

  1. Install 2 new gaskets and the 2 screw plugs to the oil filter bracket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



    G037304E01
  1. Install the oil filter bracket with the 2 bolts and nut.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    G037462E01
  1. Using a 27 mm socket wrench, install the oil filter union.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }



40. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.



    G039579E01
  1. Using SST, tighten the oil filter.

    SST
    09228-06501  

    When using a torque wrench:
    Using a torque wrench, tighten the oil filter.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }

    When not using a torque wrench:
    Tighten the oil filter an additional 3/4 turn.



41. INSTALL ENGINE REAR OIL SEAL


    A103252E01
  1. Place the oil seal retainer on wooden blocks.

  1. Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.

    SST
    09223-15030  
    09950-70010   (09951-07150)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.



42. INSTALL ENGINE REAR OIL SEAL RETAINER


    A097914E01
  1. Apply seal packing in a continuous bead as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent
    Seal width:
    2.0 to 3.0 mm (0.079 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 4 hours after installing.

  1. Install the oil seal retainer with the 6 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



43. INSTALL CYLINDER HEAD GASKET


    A097915E01
  1. Apply a continuous bead (seal width: 4.0 to 7.0 mm (0.15 to 0.28 in.)) of seal packing to the cylinder block upper side and cylinder head gasket upper side as shown in the illustration.

    Seal packing:
    Part No. 08826-00100 or equivalent
    Seal width:
    4.0 to 7.0 mm (0.15 to 0.28 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes after applying the seal packing.
    3. Install the cylinder head bolt within 15 minutes after applying the seal packing.
    4. Do not put into engine oil within 4 hours of installation.



    A101349E01
  1. Install a new cylinder head gasket on the cylinder block surface with the Lot No. stamp upper side facing upward.

    NOTICE:
    1. Make sure that the installation direction is correct.
    2. Place the cylinder head gently to avoid damaging the gasket with the bottom part of the head.



44. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head bolts are tightened in 3 progressive steps.

  1. Place the cylinder head on the cylinder block.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



    A101319E02
  1. Step 1

    1. Install and uniformly tighten the 10 cylinder head bolts with the plate washers, in several steps, in the sequence shown.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }



    A101350E02
  1. Step 2

    1. Mark the cylinder head bolt head with paint as shown in the illustration.

    2. Retighten the cylinder head bolts by 90°.

  1. Step 3

    1. Retighten the cylinder head bolts by an additional 90°.

    2. Check that the painted mark is now facing rearward.



    A101351E01
  1. Seal packing will seep out on the engine's front side. Thoroughly wipe clean any seal packing.



45. INSTALL CAMSHAFT TIMING GEAR OR SPROCKET


    A101317
  1. Clamp the camshaft in a vise and then install the camshaft timing sprocket to the camshaft with the sprocket bolt.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

    NOTICE:
    Do not damage the camshaft in the vise.



46. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY


    A101352E01
  1. Put the camshaft timing gear and camshaft together by aligning the key groove and straight pin.

  1. Lightly press the gear against the camshaft, and turn the gear. Push further at the position where the pin enters the groove.

    CAUTION:
    Do not turn the camshaft timing gear in the retard direction (the right angle).

  1. Check that there is no clearance between the gear's fringe and the camshaft.

  1. Tighten the fringe bolt with the camshaft timing gear fixed.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. Check that the camshaft timing gear can move in the retard direction (the right angle), and is locked at the most retarded position.



47. INSTALL VALVE ROCKER ARM SUB-ASSEMBLY NO.1


    G039612E02
  1. Set the 16 rocker arms to the lash adjusters.

    NOTICE:
    Before and after setting the camshaft and No.2 camshaft, firmly set the rocker arm to the lash adjuster.



48. INSTALL CAMSHAFTS


    G039613E03
  1. Apply clean engine oil to the camshaft's cam portion and the cylinder head journals.

  1. Set the camshaft and No.2 camshaft as shown in the illustration.

    NOTICE:
    Before and after setting the camshaft and No.2 camshaft, firmly set the rocker arm to the lash adjuster.



49. INSTALL CAMSHAFT BEARING CAP


    A101357
  1. Temporarily install the camshaft bearing cap No.1.

  1. Check the proper location of each camshaft bearing cap No.2 and install them.



    A101310E01
  1. Install a new O-ring to the camshaft bearing cap No.1.

  1. Temporarily install the oil delivery pipe.



    A101309E03
  1. Tighten the 21 bolts and 20 washers in the order shown in the illustration.

    Torque:
    for bolt A:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for bolts except A:
    16 N*m{ 160 kgf*cm , 11 ft.*lbf }



50. INSTALL CRANKSHAFT TIMING GEAR


    A101308
  1. Install the timing gear as shown in the illustration.



51. INSTALL CHAIN VIBRATION DAMPER NO.1


    A101306E01
  1. Install the vibration damper with the bolt and nut.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



52. INSTALL CHAIN SUB-ASSEMBLY


    A101358E02
  1. As shown in the illustration, install the chain on the sprocket and gear with the painted marks aligned with the timing marks on the sprocket and gear.

    HINT:
    1. The camshaft mark plate is yellow.
    2. The crankshaft mark plate is orange.



    A101359
  1. Use a rope to tie the chain of the crankshaft timing sprocket. Tie the rope near the sprocket.

    NOTICE:
    After the chain tensioner has been installed, the rope must be removed.

    HINT:
    The rope is tied so that the chain will not jump a tooth.



53. INSTALL CHAIN TENSIONER SLIPPER


    A101307E01
  1. Install the tensioner slipper with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



54. INSTALL CHAIN TENSIONER ASSEMBLY NO.1


    A101305
  1. Install a new gasket and the chain tensioner No.1 with the bolt and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A101303E02
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.



55. INSTALL TIMING CHAIN GUIDE


    A101304E01
  1. Install a new O-ring and the chain guide with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



56. INSTALL TIMING CHAIN CASE OIL SEAL
  1. Place the timing chain cover on wooden blocks.



    A101360E01
  1. Using SST, tap in a new oil seal until its surface is flush with the timing gear case edge.

    SST
    09223-50010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.



57. INSTALL WATER PUMP ASSEMBLY


    A101301
  1. Install a new gasket and the water pump with the 8 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



58. REMOVE OIL PUMP RELIEF VALVE
  1. Coat the relief valve with engine oil.

  1. Insert the relief valve and spring into the timing chain cover hole.

  1. Install a new gasket to the plug.



    A086864
  1. Using a 27 mm socket wrench, install the plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



59. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    A101300E02
  1. Install 3 new O-rings to the timing chain cover as shown in the illustration.



    A058128E01
  1. Apply adhesive to the timing gear case plug.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent



    G038539
  1. Using a 10 mm socket hexagon wrench, install the timing chain cover plug.

    Torque:
    17 N*m{ 170 kgf*cm , 12 ft.*lbf }



  1. Apply seal packing in a continuous bead to the timing chain cover as shown in the following illustration.


    G039490E04

    Seal packing:
    Part No. 08826-00080 or equivalent


    Seal width:

    Position
    Specified Condition
    A - A
    2.5 to 3.0 mm (0.098 to 0.118 in.)
    B - B, C -C
    4.0 to 4.5 mm (0.157 to 0.177 in.)
    D - D
    2.5 to 3.0 mm (0.098 to 0.118 in.)
    E
    3.0 to 3.5 mm (0.118 to 0.138 in.)

    NOTICE:
    1. Be sure to clean and degrease the contact surfaces, especially 4 areas indicated by ● in the illustration.
    2. When the contact surfaces are wet, wipe off with an oil-free cloth before applying seal packing.
    3. Install the crankcase within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    4. Do not start the engine for at least 4 hours after installing.



    A101362E01
  1. Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.



  1. Temporarily install the the timing chain cover with the 19 bolts and 2 nuts, but do not tighten the bolts and nuts yet.


    A101363E01

  1. Excluding bolts A, fully tighten the bolts and nuts in this order: Area 1, Area 2 and Area 3.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    Bolt length
    75 mm (2.95 in.) for bolt A (M10)
    75 mm (2.95 in.) for bolt B (M8)
    87 mm (3.43 in.) for bolt C
    95 mm (3.74 in.) for bolt D

  1. Fully tighten the bolts labeled A in this order: Area 2 and Area 3.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }

  1. Fully tighten the bolts labeled E in Area 4.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    Bolt length:
    35 mm (1.37 in.) for bolt E



60. INSTALL OIL PAN SUB-ASSEMBLY


  1. Install the stud bolt.

    1. Using an E5 "torx" socket wrench, install the stud bolts labeled A for the oil pan as shown in the illustration.



    2. Using an E7 "torx" socket wrench, install the stud bolts labeled B for the oil strainer as shown in the illustration.


      G037338E02

      Torque:
      for stud bolt A:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
      for stud bolt B:
      3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



    G037340E02
  1. Apply seal packing in a continuous bead as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent
    Seal width:
    2.0 to 3.0 mm (0.08 to 0.12 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 4 hours after installing.



    A101297E01
  1. Install a new O-ring.



    A101295E02
  1. Temporarily install the oil pan with the 16 bolts and 2 nuts.

    HINT:
    Bolt length:
    20 mm (0.79 in.) for bolt A
    40 mm (1.57 in.) for bolt B

  1. Uniformly tighten the 16 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



61. INSTALL OIL STRAINER SUB-ASSEMBLY


    A101294E03
  1. Install a new gasket and the oil strainer with the bolt and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



62. INSTALL OIL PAN SUB-ASSEMBLY NO.2


    G037317E02
  1. Apply seal packing in a continuous bead as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent
    Seal width:
    2.5 to 3.5 mm (0.098 to 0.138 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 4 hours after installing.



    A101291E02
  1. Temporarily install the oil pan with the 18 bolts and 2 nuts.

  1. Uniformly tighten the 18 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install a new gasket and the drain plug.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }



63. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley, and slide it on the pulley.



    A101367E01
  1. Using SST, install a new pulley bolt.

    Torque:
    260 N*m{ 2,650 kgf*cm , 192 ft.*lbf }

    SST
    09213-54015   (91651-60855)
    09330-00021  

    NOTICE:
    Do not reuse the pulley bolt.



64. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    A101368E01
  1. Apply seal packing as shown in the illustration.

  1. Install the 2 gaskets to the head cover.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 4 hours after installing.



    A101292
  1. Temporarily install the cover with the 19 bolts and 2 nuts.



    A101292E01
  1. Fully tighten the bolts (A) shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Fully tighten the bolts (B) shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    HINT:
    Make sure the tightening torque of bolts (A).



65. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A101285E01
  1. Install the camshaft timing oil control valve assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



66. INSTALL CRANK POSITION SENSOR


    G037915E01
  1. Apply engine oil to the O-ring.



    G037914
  1. Install the crankshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



67. INSTALL CAM POSITION SENSOR
  1. Apply engine oil to the O-ring.



    A101284E01
  1. Install the camshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



68. INSTALL VENTILATION VALVE SUB-ASSEMBLY


    A101282
  1. Install the ventilation valve sub-assembly.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



69. INSTALL OIL FILLER CAP SUB-ASSEMBLY


    A101281E01
  1. Install the oil filler cap sub-assembly.