Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › CRANKSHAFT POSITION SENSOR

CRANKSHAFT POSITION SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL CRANKSHAFT POSITION SENSOR


    G037915E01
  1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.



    G037914
  1. Install the crankshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or jammed when installing.



    G037913
  1. Connect the crankshaft position sensor connector and the 2 wire harness clamps.



2. INSTALL COMPRESSOR MOUNTING BRACKET NO.1 (w/ Air Conditioning)


    A114820E01
  1. Temporarily install the mounting bracket with the 5 bolts.

    HINT:
    Make sure that the mounting bracket is in contact with the engine block at points A shown in the illustration.

  1. Install the mounting bracket by tightening the 5 bolts in the order shown in the illustration.

    Torque:
    Bolt B:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    Except bolt B:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

    NOTICE:
    In order to prevent misalignment, which causes belt rattle, tightening of the bolts must be performed in the order shown.



3. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning)


    A102804E01
  1. Temporarily install the bolt A to install the compressor.

  1. Install the compressor completely by tightening the 4 bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    In order to prevent misalignment, which causes belt rattle, tightening of the bolts must be performed in the order shown.

  1. Connect the suction tube clamp with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the compressor connector.



4. INSTALL FAN AND GENERATOR V BELT (w/ Air Conditioning)


G035171E02
  1. Install the drive belt to the pulleys except the drive belt tensioner pulley.

  1. Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and then install the drive belt to the tensioner pulley.

    NOTICE:
    1. The backside of the drive belt should face the tensioner pulley.
    2. Check that the drive belt is properly set to each pulley.



    G036496E02
  1. After a new belt has been installed, check that the tensioner indicator mark is within range A shown in the illustration.



5. INSTALL OIL LEVEL GAUGE GUIDE (w/ Air Conditioning)


    A102132E01
  1. Install the gauge guide with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



6. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY (w/ Air Conditioning)
  1. Install the engine service hole sub cover with the 5 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



7. INSTALL FRONT DOOR SCUFF PLATE RH (w/ Air Conditioning)


8. INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type, w/ Air Conditioning)
  1. Perform the same procedure as above on the opposite side.



9. INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type, w/ Air Conditioning)
  1. Perform the same procedure as above on the opposite side.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


11. INSTALL ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1 and Air Conditioning)

Torque:
13 N*m{ 133 kgf*cm , 10 ft.*lbf }



12. REMOVE PERFORM INITIALIZATION
(Click here)