Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM

ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here



When using intelligent tester, troubleshoot in accordance with the procedure on the following pages.

HINT:
  1. The TCM of this system is connected to the CAN system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN system.
  2. The intelligent tester can be used at steps 3, 4, 6, and 9.



1.Vehicle Brought to Workshop

    NEXT


    2.Customer Problem Analysis

      NEXT


      3.Connect the intelligent tester to DLC3

        NEXT


        4.Check and Clear DTC and Freeze Frame Data

          NEXT


          5.Visual Inspection

            NEXT


            6.Setting the Check Mode Diagnosis

              NEXT


              7.Problem Symptom Confirmation


                .
                Symptom does not occur: Go to step 8

                .
                Symptom occurs: Go to step 9

                8.Symptom Simulation

                  NEXT


                  9.DTC Check


                    .
                    DTC is not output: Go to step 10

                    .
                    DTC is output: Go to step 18

                    10.Basic Inspection


                      NG.
                      Go to step 20
                      OK


                      11.Mechanical System Test


                        NG.
                        Go to step 17
                        OK


                        12.Hydraulic Test


                          NG.
                          Go to step 17
                          OK


                          13.Manual Shifting Test


                            NG.
                            Go to step 15
                            OK


                            14.Problem Symptoms Table Chapter 1


                              NG.
                              Go to step 19
                              OK


                              15.Problem Symptoms Table Chapter 2


                                NG.
                                Go to step 17
                                OK


                                16.Problem Symptoms Table Chapter 3

                                  NEXT


                                  17.Part Inspection


                                    .
                                    Go to step 20

                                    18.DTC Chart

                                      NEXT


                                      19.Circuit Inspection

                                        NEXT


                                        20.Repair or Replace

                                          NEXT


                                          21.Confirmation Test

                                            NEXT

                                            End


                                            When not using intelligent tester, troubleshoot in accordance with the procedure on the following pages.

                                            HINT:
                                            The TCM of this system is connected to the CAN system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN system.



                                            1.Vehicle Brought to Workshop

                                              NEXT


                                              2.Customer Problem Analysis

                                                NEXT


                                                3.Check and Clear DTCs

                                                  NEXT


                                                  4.Problem Symptom Confirmation


                                                    .
                                                    Symptom does not occur: Go to step 5

                                                    .
                                                    Symptom occurs: Go to step 6

                                                    5.Symptom Simulation

                                                      NEXT


                                                      6.DTC Check


                                                        .
                                                        DTC is not output: Go to step 7

                                                        .
                                                        DTC is output: Go to step 15

                                                        7.Basic Inspection


                                                          NG.
                                                          Go to step 17
                                                          OK


                                                          8.Mechanical System Test


                                                            NG.
                                                            Go to step 14
                                                            OK


                                                            9.Hydraulic Test


                                                              NG.
                                                              Go to step 14
                                                              OK


                                                              10.Manual Shifting


                                                                NG.
                                                                Go to step 12
                                                                OK


                                                                11.Problem Symptoms Table Chapter 1


                                                                  NG.
                                                                  Go to step 16
                                                                  OK


                                                                  12.Problem Symptoms Table Chapter 2


                                                                    NG.
                                                                    Go to step 14
                                                                    OK


                                                                    13.Problem Symptoms Table Chapter 3

                                                                      NEXT


                                                                      14.Part Inspection


                                                                        .
                                                                        Go to step 17

                                                                        15.DTC Chart

                                                                          NEXT


                                                                          16.Circuit Inspection

                                                                            NEXT


                                                                            17.Repair or Replace

                                                                              NEXT


                                                                              18.Confirmation Test

                                                                                NEXT

                                                                                End