Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM

ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM > TERMINALS OF ECU

for Preparation Click here



ECM

C109041E01

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specific Condition".
Use the illustration above as a reference for the ECM terminals.


Symbols (Terminals No.)
Wiring Color
Terminal Description
Condition
Specified Condition
NSW (B9-6) - E1 (D3-7)
B-W - BR
Park neutral switch signal
IG switch ON and shift lever P and N position
Below 2 V
↑
↑
↑
IG switch ON and shift lever except P and N position
10 to 14 V
STP (B7-15) - E1 (D3-7)
R-W - BR
Stop lamp switch signal
Brake pedal is depressed
7.5 to 14 V
↑
↑
↑
Brake pedal is released
Below 1.5 V
CAN+ (B7-22) - E1 (D3-7)
L - BR
CAN communication line
IG switch ON
Pulse generation
(See waveform 5)
CAN- (B7-21) - E1 (D3-7)
R - BR
CAN communication line
IG switch ON
Pulse generation
(See waveform 6)
TC (B9-11) - E1 (D3-7)
P - BR
Terminal TC of DLC3
IG switch ON
10 to 14 V

TCM

C109042E01

HINT:
Each TCM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specific Condition".
Use the illustration above as a reference for the TCM terminals.


Symbols (Terminals No.)
Wiring Color
Terminal Description
Condition
Specified Condition
L (O2-10) - E1 (O1-1)
R - BR
L shift position switch signal
IG switch ON and shift lever L position
10 to 14 V
↑
↑
↑
IG switch ON and shift lever except L position
Below 1 V
2 (O2-11) - E1 (O1-1)
Y - BR
2 shift position switch signal
IG switch ON and shift lever 2 and L position
10 to 14 V
↑
↑
↑
IG switch ON and shift lever except 2 and L position
Below 1 V
R (O2-9) - E1 (O1-1)
L - BR
R shift position switch signal
IG switch ON and shift lever R position
10 to 14 V
↑
↑
↑
IG switch ON and shift lever except R position
Below 1 V
D (O2-8) - E1 (O1-1)
R-Y - BR
D shift position switch signal
IG switch ON and shift lever D and 3 position
10 to 14 V
↑
↑
↑
IG switch ON and shift lever except D and 3 position
Below 1 V
3 (O2-12) - E1 (O1-1)
B - BR
3 shift position switch signal
IG switch ON and shift lever 3 position
10 to 14 V
↑
↑
↑
IG switch ON and shift lever except 3 position
Below 1 V
STP (O3-14) - E1 (O1-1)
R-W - BR
Stop lamp switch signal
Brake pedal is depressed
7.5 to 14 V
↑
↑
↑
Brake pedal is released
Below 1.5 V
S2 (O1-17) - E1 (O1-3)
P-L - BR
S2 solenoid signal
2nd or 3rd gear
10 to 14 V
↑
↑
↑
1st or 4th gear
Below 1 V
S1 (O1-18) - E1 (O1-3)
LG - BR
S1 solenoid signal
1st or 2nd gear
10 to 14 V
↑
↑
↑
3rd or 4th gear
Below 1 V
SLT+ (O1-20) - SLT- (O1-19)
L-B - W-L
SLT solenoid signal
Engine idle speed
Pulse generation
(See waveform 1)
SL (O1-16) - E1 (O1-3)
GR - BR
SL solenoid signal
IG switch ON
Below 1.5 V
↑
↑
↑
Vehicle driving under lock-up position
10 to 14 V
THOC (O1-24) - E2 (O1-23)
L - Y-B
ATF temperature sensor signal
No.1 ATF temperature: 115°C (239°F) or more
Below 1.5 V
SP2+ (O1-30) - SP2- (O1-29)
R - G
Speed sensor (SP2) signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 3)
NCO+ (O1-13) - NCO- (O1-2)
L - Y
Speed sensor (NCO) signal
Engine idle speed
Pulse generation
(See waveform 2)
NSW (O1-12) - E1 (O1-1)
B-W - BR
Park neutral switch signal
IG switch ON and shift lever P and N position
Below 2 V
↑
↑
↑
IG switch ON and shift lever except P and N position
10 to 14 V
STA (O1-11) - E1 (O1-1)
R - BR
Starter signal
Cranking (shift lever position P or N position, ignition switch START)
6 V or more
↑
↑
↑
IG switch ON and shift lever except P and N position
10 to 14 V
SPD1 (O3-25) - E1 (O1-1)
P-L - BR
Speed signal from combination meter
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 4)
+B (O3-5) - E1 (O1-1)
B-R - BR
Battery (for measuring battery voltage and for TCM memory)
Always
9 to 14 V
IG2 (O3-6) - E1 (O1-1)
B-R - BR
Ignition switch
Ignition switch ON
9 to 14 V
CAN+ (O3-21) - E1 (O1-1)
L - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 5)
CAN- (O3-20) - E1 (O1-1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 6)


    G023426E05
  1. Waveform 1
    Reference: 
    Terminal
    SLT+ - SLT-
    Tool setting
    5 V/DIV, 1ms/DIV
    Vehicle condition
    Engine idle speed



  2. G034873E03
  3. Waveform 2
    Reference: 
    Terminal
    NCO+ - NCO-
    Tool setting
    5 V/DIV, 0.5 ms/DIV
    Vehicle condition
    Engine idle speed (P or N position)



  4. G020664E05
  5. Waveform 3
    Reference: 
    Terminal
    SP2+ - SP2-
    Tool setting
    2 V/DIV, 20 ms/DIV
    Vehicle condition
    Vehicle speed 20 km/h (12 mph)



  6. G034872E02
  7. Waveform 4
    Reference: 
    Terminal
    SP1 - E1
    Tool setting
    2 V/DIV, 20 ms/DIV
    Vehicle condition
    Vehicle speed 20 km/h (12 mph)



  8. G036660E06
  9. Waveform 5
    Reference: 
    Terminal
    CAN+ - E1
    Tool setting
    1 V/DIV, 10 ms/DIV
    Vehicle condition
    Engine is stopped, ignition ON



  10. G036661E05
  11. Waveform 6
    Reference: 
    Terminal
    CAN- - E1
    Tool setting
    1 V/DIV, 10 ms/DIV
    Vehicle condition
    Engine is stopped, ignition ON