Home › BODY ELECTRICAL › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSPECTION

for Preparation Click here



1. INSPECT FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE)


    B111190E01
  1. Inspect the door lock motor & unlock detection switch.

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      LHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      ON (Door lock set to UNLOCK)
      7 - 8 (Below 1 Ω)
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      OFF (Door lock set to LOCK)
      7 - 8 (10 kΩ or higher)



    2. B111184E01
    3. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      RHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      ON (Door lock set to UNLOCK)
      7 - 8 (Below 1 Ω)
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      OFF (Door lock set to LOCK)
      7 - 8 (10 kΩ or higher)



    B111189E01
  1. Inspect the key lock and unlock switch.

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      LHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      10 - 7
      ON (Door lock set to UNLOCK)
      Below 1 Ω
      9 - 7
      OFF (Door lock set to LOCK)
      Below 1 Ω



    2. B111193E01
    3. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      RHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      5 - 8
      ON (Door lock set to UNLOCK)
      Below 1 Ω
      6 - 8
      OFF (Door lock set to LOCK)
      Below 1 Ω



2. REMOVE FRONT DOOR LOCK ASSEMBLY (FRONT PASSENGER SIDE)


    B111184E01
  1. Inspect the door lock motor.

    1. Apply battery voltage and check operation of the door lock motor.

      Standard:
      LHD Models:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock



    2. B111190E01
    3. Apply battery voltage and check operation of the door lock motor.

      Standard:
      RHD Models:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock



    B111193E01
  1. Inspect the key lock and unlock switch.

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      LHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      5 - 8
      ON (Door lock set to UNLOCK)
      Below 1 Ω
      6 - 8
      OFF (Door lock set to LOCK)
      Below 1 Ω



    2. B111189
    3. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      RHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      10 - 7
      ON (Door lock set to UNLOCK)
      Below 1 Ω
      9 - 7
      OFF (Door lock set to LOCK)
      Below 1 Ω