Home › TRANSMISSION · A343E AUTOMATIC TRANSMISSION › ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0705
Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
  1. NSW input signal is ON.
  2. R input signal is ON.
  3. 3 input signal is ON.
  4. 2 input signal is ON.
  5. L input signal is ON.
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (R, 3, 2 or L).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM


C109050E01


C109048E01


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the Intelligent Tester Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Intelligent Tester to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Enter / Power train / Engine and ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    P and N: ON
    Except P and N: OFF
    When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (L Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    L: ON
    Except L: OFF
    ↑
    Shift SW Status (2 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    2: ON
    Except 2: OFF
    ↑
    Shift SW Status (3 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    3: ON
    Except 3: OFF
    ↑
    Shift SW Status (R Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    ↑

1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C110340E03
  1. Jack up the vehicle.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P
    2 - 6 and 4 - 5
    Below 1 Ω
    Except P
    ↑
    10 kΩ or higher
    R
    2 - 1
    Below 1 Ω
    Except R
    ↑
    10 kΩ or higher
    N
    2 - 9 and 4 - 5
    Below 1 Ω
    Except N
    ↑
    10 kΩ or higher
    D and 3
    2 - 7
    Below 1 Ω
    Except D and 3
    ↑
    10 kΩ or higher
    2
    2 - 3
    Below 1 Ω
    Except 2
    ↑
    10 kΩ or higher
    L
    2 - 8
    Below 1 Ω
    Except L
    ↑
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


2.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY


    C113859E01
  1. Connect the park/neutral position switch connector.

  1. Disconnect the transmission control switch connector of shift lock control unit assembly.

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Resistance:
    Shift position
    Tester connection
    Specified condition
    D
    9 - 2 (NSSD - ATD)
    Below 1 Ω
    3
    10 kΩ or higher
    D
    9 - 3 (NSSD - AT3)
    10 kΩ or higher
    3
    Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    C096070E04
  1. Connect the transmission control switch connector of shift lock control unit assembly.

  1. Turn the ignition switch to the ON position, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Voltage:

    Shift Position
    Tester connection
    Specified condition
    P and N
    B9-30 (NSW) - Body ground
    Below 2 V
    Except P and N
    ↑
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    A111387E01
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to the ON position, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Voltage:

    Shift Position
    Tester connection
    Specified condition
    R
    B7-11 (R) - Body ground
    10 to 14 V*
    Except R
    ↑
    Below 1 V
    D and 3
    B7-19 (3) - Body ground
    10 to 14 V
    Except D and 3
    ↑
    Below 1 V
    2
    B7-10 (2) - Body ground
    10 to 14 V
    Except 2
    ↑
    Below 1 V
    L
    B7-9 (L) - Body ground
    10 to 14 V
    Except L
    ↑
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the turning on of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM