Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Engine Coolant Temperature Receiver Gauge Malfunction

for Preparation Click here


WIRING DIAGRAM


E109201E01


INSPECTION PROCEDURE

HINT:
If there is an open or short in the engine coolant temperature sensor circuit, the ECM outputs DTCs. Perform troubleshooting with the "SFI System" (2KD-FTV) , "ECD System" (2TR-FE) or (5L-E).

1.READ VALUE OF INTELLIGENT TESTER
  1. Operate the intelligent tester according to the steps on the display and select "DATA LIST".


ECM:

Item
Measurement Item/ Range (Display)
Normal Condition
Diagnostic Note
Coolant Temp
Coolant temperature / Min.: -40°C (-40°F), Max.: 215°C (419°F)
After warming up: 80 to 95°C (176 to 203°F)
If the value is -40°C (-40°F) or 140°C (284°F), sensor circuit is open or shorted.

OK:
Coolant temperature displayed on the tester is between 80°C (176°F) and 95°C (203°F) after warming up.



NG
GO TO ENGINE CONTROL SYSTEM
OK


2.INSPECT COMBINATION METER ASSEMBLY


    E111217E01
  1. Disconnect the connector.

  1. Measure the voltage according to the value(s) in the table below.
    Standard Voltage 
    Tester Connection
    Condition
    Specified Condition
    B9-2 (THWO) (*1) - Body ground
    Ignition switch ON
    10 to 14 V
    B7-14 (THWO) (*2) - Body ground
    Ignition switch ON
    10 to 14 V
    B10-8 (THWO) (*3) - Body ground
    Ignition switch ON
    10 to 14 V

*1: 2KD-FTV
*2: 2TR-FE
*3: 5L-E


NG
Go to step 4
OK


3.INSPECT COMBINATION METER ASSEMBLY
E109170E06
E110649E01
  1. Check the input signal wave form.

    1. Remove the combination meter with the connectors still connected.

    2. Connect the oscilloscope to terminal S (H20-17) and body ground.

    3. Start the engine.

HINT:
As engine coolant temperature rises, the period A shown in the illustration becomes longer.

Except Middle East 
Engine Coolant Temperature
A
Less than 50°C (122.0°F)
96.304 to 100.304 ms
83°C (181.4°F)
231.472 to 235.472 ms
120°C (248.0°F)
383.024 to 387.024 ms
Middle East 
Engine Coolant Temperature
A
Less than 70°C (158.0°F)
178.224 to 182.224 ms
95°C (203.0°F)
282.624 to 286.624 ms
120°C (248.0°F)
383.024 to 387.024 ms


NG
REPLACE ECM
OK

REPLACE COMBINATION METER ASSEMBLY 

4.CHECK HARNESS AND CONNECTOR (BETWEEN COMBINATION METER AND ECM)
E110641E01
  1. Disconnect the H20 and B9 (*1), B7 (*2), B10 (*3) connectors.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
S (H20-17) - THWO (B9-2)
Always
Below 1 Ω
S (H20-17) - THWO (B7-14)
Always
Below 1 Ω
S (H20-17) - THWO (B10-8)
Always
Below 1 Ω
THWO (B9-2) - Body ground
Always
10 kΩ or higher
THWO (B7-14) - Body ground
Always
10 kΩ or higher
THWO (B10-8) - Body ground
Always
10 kΩ or higher

*1: 2KD-FTV
*2: 2TR-FE
*3: 5L-E


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY