Home › TRANSMISSION ยท R351 MANUAL TRANSMISSION › MANUAL TRANSMISSION UNIT

MANUAL TRANSMISSION UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE MANUAL TRANSMISSION FILLER PLUG


    D029023
  1. Remove the filler plug and gasket from the transmission case.



2. REMOVE DRAIN (MTM) PLUG SUB-ASSEMBLY


    D029024
  1. Remove the drain plug and gasket from the transmission case.



3. REMOVE CLUTCH HOUSING


    D029028
  1. Remove the 9 bolts.



    D029029
  1. Using a plastic hammer, remove the clutch housing from the transmission case.



4. REMOVE BACK UP LIGHT SWITCH ASSEMBLY


    C114270E01
  1. Using SST, remove the back up light switch and gasket from the transmission case.



5. REMOVE SPEEDOMETER SENSOR
  1. Remove the bolt and speedometer sensor from the extension housing.

  1. Remove the O-ring from the speedometer sensor.



6. REMOVE EXTENSION HOUSING (MTM) COVER


    C112987
  1. Remove the 6 bolts, extension housing (MTM) cover and gasket.



7. REMOVE EXTENSION HOUSING DUST (MTM) DEFLECTOR
  1. Using a brass bar and a hammer, remove the extension housing dust deflector from the extension housing.



8. REMOVE SHIFT LEVER SHAFT HOUSING SUB-ASSEMBLY


    C090700
  1. Remove the 6 bolts.



    D025940
  1. Using a plastic hammer, remove the shift lever shaft housing sub-assembly.



9. REMOVE EXTENSION (MTM) HOUSING SUB-ASSEMBLY


    B085186
  1. Remove the 10 bolts.

  1. Using a plastic hammer, remove the extension housing.



10. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE
  1. Remove the bolt and oil receiver pipe from the extension housing.



11. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE NO.1


    D029037
  1. Remove the extension housing oil receiver pipe No.1.



12. REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL


    D029043
  1. Using a screwdriver and hammer, remove the extension housing oil seal from the extension housing.



13. REMOVE BEARING RETAINER FRONT (MTM)


    D025950
  1. Remove the 8 bolts.



    D025951
  1. Using a brass bar and hammer, remove the retainer from the transmission case.



14. REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL


    D025952E01
  1. Fix the front bearing retainer in a vise in aluminum plate.

  1. Using SST, remove the transmission front bearing retainer oil seal.

    SST
    09308-00010  



15. REMOVE FRONT BEARING SHAFT SNAP RING


    D025953
  1. Using a snap ring expander, remove the front bearing shaft snap ring from the transmission case.



16. REMOVE COUNTER GEAR FRONT BEARING SNAP RING NO.1


    D025954
  1. Using a snap ring expander, remove the counter gear front bearing snap ring No.1 from the transmission case.



17. REMOVE MANUAL TRANSMISSION CASE


    D029044
  1. Using a brass bar and hammer, remove the transmission case from the intermediate plate.



18. REMOVE TRANSMISSION MAGNET


    D025957
  1. Remove the transmission magnet from the intermediate plate.



19. FIX INTERMEDIATE PLATE


    D025958
  1. Fix the intermediate plate in a vise in between aluminum plates.



20. REMOVE SHIFT DETENT BALL SPRING SEAT NO.1


    D029046
  1. Using a "torx" socket wrench T40, remove the shift detent ball spring seat No.1 from the intermediate plate.



    D025960
  1. Using a magnetic finger, remove the compression spring and the shift detent ball from the intermediate plate.



    D033569E03
  1. Using a "torx" socket wrench T40, remove the 2 shift detent ball spring seats No.1 from the intermediate plate.



    D033570
  1. Using a magnetic finger, remove the 2 compression springs and the 2 shift detent balls from the intermediate plate.



21. REMOVE SHIFT FORK SHAFT STOPPER


    D025963
  1. Using a pin punch (5 mm) and hammer, remove the slotted spring pin from the gear shift fork shaft No.1.

  1. Remove the shift fork shaft stopper from the gear shift fork shaft No.1.



22. REMOVE GEAR SHIFT FORK SHAFT NO.1


    D025964
  1. Using 2 screwdrivers and a hammer, remove the snap ring from the gear shift fork shaft No.1.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    D025965
  1. Remove the shift fork set bolt from the gear shift fork No.1.



    C089434
  1. Remove the gear shift fork shaft No.1 from the intermediate plate.



    D025967
  1. Using a magnetic finger, remove the shift interlock No.1 roller and the shift interlock pin (ball) from the intermediate plate.



23. REMOVE GEAR SHIFT HEAD NO.1


    D025968
  1. Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the gear shift head No.1.

  1. Remove the gear shift head No.1 from the shift fork shaft No.1.



24. REMOVE SHIFT FORK SHAFT STOPPER


    D025969
  1. Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the gear shift fork shaft No.2.

  1. Remove the shift fork shaft stopper from the gear shift fork shaft No.2.



25. REMOVE GEAR SHIFT FORK SHAFT NO.2


    D025970
  1. Using 2 screwdrivers and a hammer, remove the snap ring from the gear shift fork shaft No.2.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    D025971
  1. Remove the shift fork set bolt from the gear shift fork No.2.



    D025972
  1. Using a pin punch (5 mm) and hammer, remove the slotted spring pin from the gear shift fork shaft No.2.



    C089436
  1. Remove the gear shift fork shaft No.2 and gear shift head No.2.



    C089838
  1. Remove the gear shift fork No.1 and gear shift fork No.2 from the output shaft.



    D025975
  1. Using a magnetic finger, remove the shift interlock No.1 roller from the intermediate plate.



26. REMOVE REVERSE SHIFT FORK SHAFT


    D025976
  1. Using a pin punch (5 mm) and hammer, remove the slotted spring pin from the reverse shift fork shaft.



    D025977
  1. Using 2 screwdrivers and a hammer, remove the snap ring from the reverse shift fork shaft.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    C089438
  1. Remove the reverse shift fork shaft and gear shift fork No.3.



    D025975
  1. Using a magnetic finger, remove the shift interlock No.1 roller from the intermediate plate.



    D025979
  1. Using a magnetic finger, remove the reverse shift fork ball from the reverse shift fork.



27. REMOVE GEAR SHIFT HEAD NO.1


    D025968
  1. Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the gear shift head No.1.

  1. Remove the gear shift head No.1 from the reverse shift fork shaft.



28. REMOVE GEAR SHIFT FORK SHAFT NO.4


    D025980
  1. Using 2 screwdrivers and a hammer, remove the shift fork shaft snap ring from the gear shift fork shaft No.4.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    C089440
  1. Remove the shift fork shaft No.4 from the intermediate plate.

    NOTICE:
    Cover the hole with a shop rag to prevent the reverse shift fork ball from popping out.



    D025982
  1. Using a magnetic finger, remove the compression spring from the reverse shift fork.



29. REMOVE REVERSE SHIFT FORK


    D025983
  1. Remove the reverse shift fork together with the reverse shift arm from the intermediate plate.



    D025984
  1. Using a screwdriver, remove the reverse shift arm end shaft ring and the reverse shift fork from the reverse shift arm.



30. REMOVE REVERSE SHIFT ARM BRACKET


    D025985
  1. Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.



31. REMOVE SPEEDOMETER DRIVE (MTM) GEAR


    G034243
  1. Using snap ring expander, remove the snap ring.

  1. Remove the speedometer drive gear and ball.

  1. Using a magnetic finger, remove the steel ball.

  1. Using snap ring expander, remove the snap ring.



32. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING


    D029059
  1. Using 2 screwdrivers and a hammer, remove the output shaft bearing shaft snap ring from the output shaft.



33. REMOVE OUTPUT SHAFT REAR BEARING


    D025987E02
  1. Using SST, remove the output shaft rear bearing and output shaft spacer from the output shaft.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



34. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE


    D025991
  1. Using a feeler gauge, measure the counter shaft 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)



35. INSPECT COUNTER SHAFT 5TH GEAR RADIAL CLEARANCE


    D025992
  1. Using a dial indicator, measure the radial clearance of the counter shaft 5th gear.

    Standard clearance:
    0.015 to 0.068 mm (0.0059 to 0.0027 in.)

    If the clearance is not within the specified values, replace the counter 5th gear bearing with a new one.



36. REMOVE COUNTER GEAR REAR SHAFT SNAP RING


    D025993
  1. Using 2 screwdrivers and a hammer, remove the counter gear rear shaft snap ring from the counter gear.



37. REMOVE GEAR SPLINE PIECE NO.5


    D025994E01
  1. Using SST, remove the gear spline piece No.5 from the counter gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021, 09957-04010)



38. REMOVE SYNCHRONIZER RING OUTER NO.3


    D029060
  1. Remove the synchronizer ring outer No.3 from the counter gear.



39. REMOVE COUNTER SHAFT 5TH GEAR


    D029061
  1. Remove the counter shaft 5th gear and transmission hub sleeve No.3 assembly from the counter gear.



40. REMOVE COUNTER 5TH GEAR BEARING


    C089839
  1. Remove the counter 5th gear bearing from the counter 5th gear.



41. REMOVE TRANSMISSION HUB SLEEVE NO.3


    D029062
  1. Using a snap ring expander, remove the snap ring.



    D029063
  1. Remove the transmission hub sleeve No.3, 2 synchromesh shifting keys No.3 and 2 synchromesh shifting key springs No.3 from the counter shaft 5th gear.



42. REMOVE 5TH GEAR THRUST WASHER


    D025999
  1. Remove the 5th gear thrust washer from the counter gear.



43. REMOVE 5TH GEAR THRUST WASHER PIN


    D026000
  1. Remove the 5th gear thrust washer pin from the counter gear.



44. REMOVE OUTPUT SHAFT REAR BEARING (MTM) RETAINER


    D026001
  1. Remove the 4 bolts and output shaft rear bearing retainer from the intermediate plate.



45. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY


    D026002E03
  1. Pull out the reverse idler gear shaft to the rear side and remove the reverse idler gear from the intermediate plate.



46. REMOVE COUNTER SHAFT CENTER BEARING


    D029260
  1. Using a snap ring expander, remove the snap ring.



    D026004E01
  1. Using SST, remove the counter shaft center bearing from the intermediate plate.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

    HINT:
    Remove the bearing while tapping the tip of the counter gear so that the counter gear assembly is not pushed forward into the side wall of the output shaft gear.



47. REMOVE COUNTER GEAR


    D026005
  1. Remove the counter gear assembly from the intermediate plate.



48. REMOVE INPUT SHAFT ASSEMBLY


    D026006
  1. Remove the input shaft assembly and synchronizer ring No.2 from the output shaft.

    NOTICE:
    Do not drop the input shaft bearing and synchronizer ring No.2.



49. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING


    D029064
  1. Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft.



50. REMOVE OUTPUT SHAFT ASSEMBLY


    D029065
  1. Using a plastic hammer, remove the output shaft assembly by tapping the intermediate plate.