Home › TRANSMISSION ยท R351 MANUAL TRANSMISSION › MANUAL TRANSMISSION UNIT

MANUAL TRANSMISSION UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL OUTPUT SHAFT ASSEMBLY


    D029112
  1. Apply gear oil to the sliding part of the output assembly.

  1. Using a plastic hammer, install the output shaft assembly by tapping the intermediate plate.



2. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING


    D029064
  1. Using a snap ring expander, install the output shaft bearing shaft snap ring to the output shaft.



3. INSTALL INPUT SHAFT ASSEMBLY


    D026006
  1. Apply gear oil to the input shaft assembly and synchronizer ring No.2, and install them to the output shaft.

    NOTICE:
    1. Make sure that the synchromesh shifting key No.2 fits into the grooves of the synchronizer ring No.2.
    2. Check that the input shaft assembly rotates smoothly.



4. INSTALL COUNTER GEAR


    D026005
  1. Temporarily install the counter gear assembly to the intermediate plate.



5. INSTALL COUNTER SHAFT CENTER BEARING


    D029113E01
  1. Using SST and a hammer, install a new counter shaft center bearing to the intermediate plate.

    SST
    09316-60011   (09316-00011)

    HINT:
    Remove the bearing while tapping the tip of the counter gear so that the counter gear assembly is not pushed forward into the side wall of the output shaft gear.



6. INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY


    D026002E04
  1. Apply gear oil to each sliding part of the reverse idler gear and the reverse idler gear shaft, and install them to the intermediate plate.

    NOTICE:
    Orient the groove side of the reverse idler shaft to the rear side and install it from the rear side.



7. INSTALL OUTPUT SHAFT REAR BEARING (MTM) RETAINER


    D026001
  1. Install the output shaft rear bearing retainer into the groove of the reverse idler gear shaft with the 4 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }



8. INSTALL 5TH GEAR THRUST WASHER PIN


    D026000
  1. Apply MP grease to the 5th gear thrust washer pin, and install it to the counter gear.



9. INSTALL 5TH GEAR THRUST WASHER


    D025999
  1. Apply gear oil to the 5th gear thrust washer, and install it to the counter gear.

    NOTICE:
    Install the thrust washer so that its chamfer side faces to the front side.



10. INSTALL TRANSMISSION HUB SLEEVE NO.3


    D029063
  1. Apply gear oil to the sliding part of the transmission hub sleeve No.3, and install it to the counter shaft 5th gear.

    NOTICE:
    Make sure that the transmission hub sleeve No.3 and counter 5th gear are oriented in the correct direction.

  1. Install the 2 synchromesh shifting keys No.3 and the 2 synchromesh shifting key springs to the counter shaft 5th gear.



    D029062
  1. Using a snap ring expander, install the bearing shaft snap ring to the counter 5th gear.



11. INSTALL COUNTER 5TH GEAR BEARING


    D026020E02
  1. Apply gear oil to the counter 5th gear bearing and install it to the counter 5th gear.



12. INSTALL COUNTER SHAFT 5TH GEAR


    D025996
  1. Apply gear oil to the counter 5th gear and transmission hub sleeve No.3 assembly, and install them to the counter gear.



13. INSTALL SYNCHRONIZER RING OUTER NO.3


    D029060
  1. Apply gear oil to the synchronizer ring outer No.3, and install it to the counter gear.

    NOTICE:
    Make sure that the synchromesh shifting key No.3 fits into the grooves of the synchronizer ring outer No.3.



14. INSTALL GEAR SPLINE PIECE NO.5


    D026022E01
  1. Using SST and a press, install the gear spline piece No.5 to the counter gear.

    SST
    09316-60011   (09316-00011)

    NOTICE:
    Check that the gear rotates smoothly.



15. INSTALL COUNTER GEAR REAR SHAFT SNAP RING
  1. Select a counter gear rear shaft snap ring so that the thrust gap between the gear spline piece No.5 and counter gear rear shaft snap ring is within the specified values. Use a brass bar and a hammer, install it to the counter gear.

    Standard clearance:
    0.1 mm (0.0039 in.) or less

    Mark
    Thickness: mm (in.)
    A
    2.80 to 2.85 (0.1102 to 0.1122)
    B
    2.85 to 2.90 (0.1122 to 0.1141)
    C
    2.90 to 2.95 (0.1141 to 0.1160)
    D
    2.95 to 3.00 (0.1160 to 0.1181)
    E
    3.00 to 3.05 (0.1181 to 0.1200)
    F
    3.05 to 3.10 (0.1200 to 0.1220)
    G
    3.10 to 3.15 (0.1220 to 0.1240)



16. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE


    D025991
  1. Using a feeler gauge, measure the counter shaft 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)



17. INSPECT COUNTER SHAFT 5TH GEAR RADIAL CLEARANCE


    D025992
  1. Using a dial indicator, measure the radial clearance of the counter shaft 5th gear.

    Standard clearance:
    0.015 to 0.068 mm (0.0059 to 0.0027 in.)

    If the clearance is not within the specified values, replace the counter 5th gear bearing with a new one.



18. INSTALL OUTPUT SHAFT REAR BEARING


    D026024E01
  1. Using SST and a press, install a new spacer and output shaft rear bearing to the output shaft.

    SST
    09309-35010  



19. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING
  1. Select an output shaft bearing shaft snap ring so that the thrust gap between the snap ring and the bearing is within the specified values. Use a brass bar and a hammer to install it to the output shaft.

    Standard clearance:
    0.1 mm (0.0039 in.) or less

    Mark
    Thickness: mm (in.)
    A
    2.65 to 2.70 (0.1043 to 0.1063)
    B
    2.70 to 2.75 (0.1063 to 0.1083)
    C
    2.75 to 2.80 (0.1083 to 0.1102)
    D
    2.80 to 2.85 (0.1102 to 0.1122)
    E
    2.85 to 2.90 (0.1122 to 0.1141)
    F
    2.90 to 2.95 (0.1141 to 0.1160)
    G
    2.95 to 3.00 (0.1160 to 0.1181)
    H
    3.00 to 3.05 (0.1181 to 0.1200)
    J
    3.05 to 3.10 (0.1200 to 0.1220)
    K
    3.10 to 3.15 (0.1220 to 0.1240)
    L
    3.15 to 3.20 (0.1240 to 0.1260)
    M
    3.20 to 3.25 (0.1260 to 0.1280)
    N
    3.25 to 3.30 (0.1280 to 0.1299)
    P
    3.30 to 3.35 (0.1299 to 0.1319)
    Q
    3.35 to 3.40 (0.1319 to 0.1339)
    R
    3.40 to 3.45 (0.1339 to 0.1358)
    S
    3.45 to 3.50 (0.1358 to 0.1378)



20. INSTALL SPEEDOMETER DRIVE (MTM) GEAR
  1. Install the output shaft spacer.



    G034243
  1. Using snap ring expander, install the snap ring.

  1. Install the ball and drive gear.

  1. Using snap ring expander, install the snap ring.



21. INSTALL REVERSE SHIFT ARM BRACKET


    D025985
  1. Install the reverse shift arm bracket to the intermediate plate with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }



22. INSTALL REVERSE SHIFT FORK


    D026025
  1. Install the reverse shift arm to the reverse shift fork. Using a screwdriver and a hammer, install a new reverse shift arm end shaft ring.



    D026026
  1. Install the tip of the reverse shift arm to the reverse idler gear. Align the cut end of the reverse shift arm with the reverse shift arm bracket pin, and install them.



23. INSTALL GEAR SHIFT FORK SHAFT NO.4


    D026027
  1. Install the compression spring and the reverse shift fork ball into the reverse shift fork.



    C089441
  1. Apply gear oil to the sliding part of the gear shift fork shaft No.4.

  1. Using a screwdriver, install the gear shift fork shaft No.4 by gently pushing the reverse shift fork ball.



    D026028
  1. Using a brass bar and a hammer, install the shift fork shaft snap ring to the gear shift fork shaft No.4.



24. INSTALL GEAR SHIFT HEAD NO.1


    D025968
  1. Apply gear oil to the gear shift head No.1, and install it to the reverse shift fork shaft.

  1. Using a pin punch (5 mm) and a hammer, install the slotted spring pin into the reverse shift fork shaft.



25. INSTALL REVERSE SHIFT FORK SHAFT


    D025979
  1. Install the reverse shift fork ball into the reverse shift fork.



    D025975
  1. Install the shift interlock No.1 roller to the intermediate plate.



    C089439
  1. Install the shift fork No.3 to the transmission hub sleeve No.3 and the reverse shift fork shaft to the intermediate plate from the front side.



    D026029
  1. Using a brass bar and a hammer, install the snap ring to the reverse shift fork shaft.



    D025976
  1. Using a pin punch (5 mm) and a hammer, install the slotted spring pin into the gear shift fork No.3.



26. INSTALL GEAR SHIFT FORK SHAFT NO.2


    D025975
  1. Install the shift interlock No.1 roller to the intermediate plate.



    C089838
  1. Install the gear shift fork No.1 to the reverse gear.

  1. Install the gear shift fork No.2 to the transmission hub sleeve No.2.



    C089437
  1. Install the gear shift head No.2 and gear shift fork shaft No.2 to the intermediate plate from the front side.



    D025972
  1. Using a pin punch (5 mm) and a hammer, install the slotted spring pin into the gear shift fork No.2.



    D025971
  1. Install a new shift fork set bolt to the gear shift fork No.2.

    Torque:
    20 N*m{ 204 kgf*cm , 14 ft.*lbf }



    D026030
  1. Using a brass bar and a hammer, install the snap ring to the gear shift fork shaft No.2.



27. INSTALL SHIFT FORK SHAFT STOPPER


    D025969
  1. Install the shift fork shaft stopper to the gear shift fork shaft No.2.

  1. Using a pin punch (5 mm) and a hammer, install the slotted spring pin into the gear shift fork shaft No.2.



28. INSTALL GEAR SHIFT HEAD NO.1


    D025968
  1. Apply gear oil to the gear shift head No.1, and install it to the shift fork shaft No.1.

  1. Using a pin punch (5 mm) and a hammer, install the slotted spring pin into the shift fork shaft No.1.



29. INSTALL GEAR SHIFT FORK SHAFT NO.1


    D025967
  1. Install the shift interlock pin (ball) and shift interlock No.1 roller into the intermediate plate.



    C089435
  1. Apply gear oil to the gear shift fork shaft No.1, and install it to the intermediate plate from the front side.



    D025965
  1. Install a new shift fork set bolt to the gear shift fork No.1.

    Torque:
    20 N*m{ 204 kgf*cm , 14 ft.*lbf }



    D026031
  1. Using a brass bar and a hammer, install the snap ring to the gear shift fork shaft No.1.



30. INSTALL SHIFT FORK SHAFT STOPPER


    D025963
  1. Install the shift fork shaft stopper to the gear shift fork shaft No.1.

  1. Using a pin punch (5 mm) and a hammer, install the slotted spring pin into the gear shift fork shaft No.2.



31. INSTALL SHIFT DETENT BALL SPRING SEAT NO.1


    D025962
  1. Install the 2 compression springs and 2 shift detent balls into the intermediate plate.



    D029047E01
  1. Using a "torx" socket wrench T40, install the 2 shift detent ball spring seats No.1 to the intermediate plate.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }



    D025960
  1. Install the shift detent ball and the compression spring into the intermediate plate.



    D029046
  1. Using a "torx" socket wrench T40, install the shift detent ball spring seat No.1 to the intermediate plate.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }



32. INSTALL TRANSMISSION MAGNET


    D025957
  1. Clean the transmission magnet, and install it to the intermediate plate.



33. INSTALL MANUAL TRANSMISSION CASE


    D026033
  1. Apply seal packing to the manual transmission case as shown in the illustration.

    Seal packing:
    Part No.08826-00090, THREE BOND 1281 or equivalent



    D029117
  1. Using a plastic hammer, tap the manual transmission case to attach it to the intermediate plate.



34. INSTALL COUNTER GEAR FRONT BEARING SNAP RING NO.1


    D025954
  1. Using a snap ring expander, install the counter gear front bearing snap ring No.1 to the transmission case.



35. INSTALL FRONT BEARING SHAFT SNAP RING


    D025953
  1. Using a snap ring expander, install the front bearing shaft snap ring to the transmission case.



36. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL


    D026035E02
  1. Using SST and a hammer, install a new transmission front bearing retainer oil seal to the transmission front bearing retainer.

    SST
    09950-60010   (09951-00300, 09951-00520, 09952-06010, 09951-07100)

    Drive in depth:
    11.2 to 12.2 mm (0.4409 to 0.4803 in.)

  1. Coat the lip of the oil seal with MP grease.



37. INSTALL BEARING RETAINER FRONT (MTM)


    D026036
  1. Apply seal packing to the bearing retainer front as shown in the illustration.

    Seal packing:
    Part No.08826-00090, THREE BOND 1281 or equivalent



    D025950
  1. Install the front bearing retainer to the transmission case with the 8 bolts.

    Torque:
    17 N*m{ 170 kgf*cm , 12 ft.*lbf }

  1. Check that the input shaft and output shaft rotate smoothly.



38. INSTALL MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL


    F050676E01
  1. Using SST and a hammer, install a new extension housing oil seal to the extension housing.

    SST
    09710-30050  
    09950-70010   (09951-07100)

    Drive in depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)

    NOTICE:
    Be careful not to damage the oil seal lip.

  1. Lightly apply MP grease to the tip of the oil seal.



39. INSTALL EXTENSION HOUSING OIL RECEIVER PIPE
  1. Install the oil receiver pipe with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



40. INSTALL EXTENSION HOUSING OIL RECEIVER PIPE NO.1


    D029037
  1. Install the extension housing oil receiver pipe No.1 to the extension housing.



41. INSTALL EXTENSION (MTM) HOUSING SUB-ASSEMBLY


    D029067
  1. Apply seal packing to the extension housing as shown in the illustration.

    Seal packing:
    Part No. 08826-00090, THREE BOND 1218 or equivalent



    B085186
  1. Install the extension housing to the transmission case with the 10 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



42. INSTALL SHIFT LEVER SHAFT HOUSING SUB-ASSEMBLY


    C114271
  1. Apply seal packing to the shift lever shaft housing as shown in the illustration.

    Seal packing:
    Part No. 08826-00090, THREE BOND 1218 or equivalent



    C090700
  1. Install the shift lever shaft housing to the transmission case with the 6 bolts.

    Torque:
    17 N*m{ 170 kgf*cm , 12 ft.*lbf }



43. INSTALL EXTENSION HOUSING DUST (MTM) DEFLECTOR
  1. Using a plastic hammer, install the extension housing dust deflector to the extension housing.



44. INSTALL EXTENSION HOUSING (MTM) COVER


    C112987
  1. Install the extension housing (MTM) cover and a new gasket to the extension housing with the 6 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }



45. INSTALL SPEEDOMETER SENSOR
  1. Install a new O-ring to the speedometer sensor.

  1. Install the speedometer sensor with the bolt.

    Torque:
    11 N*m{ 115 kgf*cm , 8 ft.*lbf }



46. INSTALL BACK UP LIGHT SWITCH ASSEMBLY


    C114270E01
  1. Using SST, install the back up light switch assembly and the gasket to the transmission case.

    SST
    09817-16011  

    Torque:
    44 N*m{ 450 kgf*cm , 32 ft.*lbf }



47. INSTALL CLUTCH HOUSING


    D029028
  1. Install the clutch housing to the transmission case with the 9 bolts.

    Torque:
    36 N*m{ 370 kgf*cm , 27 ft.*lbf }



48. INSTALL DRAIN (MTM) PLUG SUB-ASSEMBLY


    D025930
  1. Install the drain plug to the transmission case through a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



49. INSTALL MANUAL TRANSMISSION FILLER PLUG


    D029023
  1. Install the filler plug to the transmission case through a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }