Home › BRAKE › BRAKE › LOAD SENSING PROPORTIONING VALVE

LOAD SENSING PROPORTIONING VALVE > ON-VEHICLE INSPECTION

for Preparation Click here



1. SET REAR AXLE LOAD

  1. C102556

    HINT:
    If the vehicle unladen weight exceeds the specification, set it by following step 5.


    Rear axle load (including vehicle weight):
    Standard body type:
    Model
    Rear axle load kg (lb)
    ***202R (L) - *E****
    850 (1,870)
    ***203R (L) - *E****
    850 (1,870)
    Others
    900 (1,980)
    Wide long body type:
    Model
    Rear axle load kg (lb)
    TRH213R - KDPNK
    1000 (2,200)
    **H212R (L) - *****
    1050 (2,310)
    **H213R (L) - *****
    1050 (2,310)
    Wide super long body type:
    Model
    Rear axle load kg (lb)
    **H220R (L) - ******
    1050 (2,310)
    **H221R (L) - ******
    1050 (2,310)
    Others
    1000 (2,200)



2. INSTALL LSPV GAUGE (SST) AND BLEED AIR
SST
09709-29018  

  1. C102558


3. RAISE FRONT BRAKE PRESSURE 9,807 kPa (100 kgf/cm2, 1,422 psi) AND CHECK REAR BRAKE PRESSURE

  1. C102558
  2. HINT:
    Gradually depress on the brake pedal until the pressure reaches the specified valve. Do not overshoot the specified pressure. Read the value of rear pressure 2 seconds after adjusting to the specified fluid pressure.


    Rear brake fluid pressure table:
    Standard body type:
    Model
    Rear brake pressure
    kPa (kgf/cm2, psi)
    ***202R (L) - *E****
    5860 +- 800
    (60 +- 8, 850 +- 116)
    ***203R (L) - *E****
    5860 +- 800
    (60 +- 8, 850 +- 116)
    Others
    5860 +- 800
    (60 +- 8, 850 +- 116)
    Wide long body type:
    Model
    Rear brake pressure
    kPa (kgf/cm2, psi)
    **H212R (L) - ******
    6600 +- 800
    (67 +- 8, 957 +- 116)
    **H213R (L) - ******
    6600 +- 800
    (67 +- 8, 957 +- 116)
    Wide super body type:
    Model
    Rear brake pressure
    kPa (kgf/cm2, psi)
    **H220R (L) - ******
    6600 +- 800
    (67 +- 8, 957 +- 116)
    **H221R (L) - ******
    6600 +- 800
    (67 +- 8, 957 +- 116)
    Others
    6600 +- 800
    (67 +- 8, 957 +- 116)



4. RAISE FRONT BRAKE PRESSURE 11,768 kPa (120 kgf/cm2, 1,707 psi) AND CHECK REAR BRAKE PRESSURE

Rear brake fluid pressure table:
Standard body type:
Model
Rear brake pressure
kPa (kgf/cm2, psi)
***202R (L) - *E****
6400 +- 1000
(65 +- 10, 928 +- 145)
***203R (L) - *E****
6400 +- 1000
(65 +- 10, 928 +- 145)
Others
6400 +- 1000
(65 +- 10, 928 +- 145)
Wide long body type:
Model
Rear brake pressure
kPa (kgf/cm2, psi)
**H212R (L) - ******
7100 +- 1000
(72 +- 10, 1030 +- 145)
**H213R (L) - ******
7100 +- 1000
(72 +- 10, 1030 +- 145)
Wide super body type:
Model
Rear brake pressure
kPa (kgf/cm2, psi)
**H220R (L) - ******
7100 +- 1000
(72 +- 10, 1030 +- 145)
**H221R (L) - ******
7100 +- 1000
(72 +- 10, 1030 +- 145)
Others
7100 +- 1000
(72 +- 10, 1030 +- 145)



5. IF VEHICLE UNLADEN WEIGHT EXCEEDS SPECIFICATION, SET IT BY FOLLOWING STEPS


    B066592E01
  1. Make a graph of rear axle load and brake fluid pressure as shown in example 1 or 2, using the applicable data of ABC point data table.

  1. Input the rear axle load on the applicable graph and find out the fluid pressure crossover point.
    Example: When the rear axle load is 1,200 kg (2,646 lb), the fluid pressure crossover point is 6,865 kPa (70 kgf/cm2, 996 psi).



  1. Calculate the rear brake pressure when the front brake pressure is 9,807 kPa (100 kgf/cm2, 1,422 psi) using the following formula.
    X: Fluid Pressure Crossover Point
    X + (100 - X) x 0.25
    Example:
    X: 6,865 kPa (70 kgf/cm2, 996 psi)
    70 + (100 - 70) x 0.25= 77.5
    Rear brake pressure: 7,600 kPa (77.5 kgf/cm2, 1,102 psi)
    Service limit: +- 800 kPa (8 kgf/cm2, 116 psi)


    C116334E01


    ABC point data table:

    Standard body type 
    Model
    A
    B
    C
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    ***200R (L) - ******
    ***201R (L) - ******
    693
    (1,528, 6.79)
    1000
    (10, 145)
    892
    (1,967, 8.74)
    4,500
    (46, 653)
    1,470
    (3,241, 14.41)
    9,600
    (98, 1,392)
    ***202R (L) - *D****
    ***203R (L) - *D****
    748
    (1,649, 7.33)
    1000
    (10, 145)
    882
    (1,945, 8.65)
    4,400
    (45, 638)
    1,405
    (3,098, 13.77)
    9,300
    (95, 1,349)
    ***202R (L) - *E****
    ***203R (L) - *E****
    710
    (1,565, 6.96)
    1000
    (10, 145)
    882
    (1,945, 8.65)
    5,300
    (54, 769)
    1,640
    (3,616, 16.07)
    11,900
    (121, 1,726)

    Wide long body type 
    Model
    A
    B
    C
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    TRH213R - KDPNK
    801
    (1,766, 7.85)
    2,500
    (25, 363)
    -
    -
    1,580
    (3,483, 15.48)
    13,700
    (140, 1,987)
    **H212R (L) - *****
    **H213R (L) - *****
    781
    (1,722, 7.65)
    2,500
    (25, 363)
    882
    (1,945, 8.65)
    4,400
    (45, 638)
    1,690
    (3,726, 16.56)
    9,900
    (101, 1,436)

    Wide super long body type 
    Model
    A
    B
    C
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    **H220R (L) - ******
    **H221R (L) - ******
    760
    (1,676, 7.44)
    2,500
    (25, 363)
    935
    (2,061, 9.16)
    4,800
    (49, 696)
    1,640
    (3,616, 16.07)
    9,500
    (97, 1,378)
    **H222R (L) - ******
    **H223R (L) - ******
    837
    (1,845, 8.20)
    2,500
    (25, 363)
    995
    (2,164, 9.76)
    5,500
    (56, 798)
    1,740
    (3,836, 17.05)
    10,400
    (106, 1,508)



6. IF NECESSARY, ADJUST FLUID PRESSURE


    C102559E01
  1. Adjust the length of the shackle.
    Lower pressure - Lengthen "A"
    High pressure - Shorten "A"

    Initial set:
    120 mm (4.72 in.)

    Adjusting:
    112 to 128 mm (4.40 to 5.04 in.)



    C102561
  1. If the pressure cannot be adjusted by the shackle, raise or lower the valve body.
    Lower pressure - Lower
    High pressure - Raise

  1. Torque the nuts.

    Torque:
    12.5 N*m (130 kgf*cm, 9 ft.*lbf)

  1. Adjust the length of the shackle again.
    If it cannot be adjusted, inspect the valve body.



7. REMOVE LSPV GAUGE (SST) AND BLEED BRAKE SYSTEM