Home › TRANSMISSION ยท G55 MANUAL TRANSMISSION › MANUAL TRANSMISSION UNIT

MANUAL TRANSMISSION UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE MANUAL TRANSMISSION FILLER PLUG


    C086347
  1. Remove the filler plug and gasket from the manual transmission case.



2. REMOVE DRAIN (MTM) PLUG SUB-ASSEMBLY


    D029129
  1. Remove the drain plug and gasket from the manual transmission case.



3. REMOVE SPEEDOMETER SENSOR


    C112968
  1. Remove the bolt and speedometer sensor.

  1. Using a screwdriver, remove the O-ring from the speedometer sensor.



4. REMOVE BACK UP LIGHT SWITCH ASSEMBLY


    C086355E01
  1. Using SST, remove the back up light switch assembly and gasket from the manual transmission case.

    SST
    09817-16011  



5. REMOVE CLUTCH HOUSING


    D029131
  1. Remove the 9 bolts.



    C086357
  1. Using a plastic hammer, remove the clutch housing from the transmission case.



6. REMOVE SHIFT LEVER SHAFT HOUSING SUB-ASSEMBLY


    C112972E01
  1. Remove the 6 bolts, shift lever shaft housing and clamp from the manual transmission case.

  1. Remove the shift lever shaft housing gasket from the manual transmission case.



7. REMOVE EXTENSION HOUSING DUST (MTM) DEFLECTOR


    C086359
  1. Using a brass bar and a hammer, remove the extension housing dust deflector from the extension housing.



8. REMOVE EXTENSION (MTM) HOUSING SUB-ASSEMBLY


    C112973
  1. Remove 8 bolts.



    C086361
  1. Using a plastic hammer, remove the extension housing from the manual transmission case.



9. REMOVE TRANSMISSION MAGNET


    D029141
  1. Remove the transmission magnet from the extension housing.



10. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE


    C086363
  1. Remove the bolt and extension housing oil receiver pipe from the extension housing.



11. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE NO.1


    D029142
  1. Remove the extension housing oil receiver pipe No.1 from the extension housing.



12. REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL


    C086365E01
  1. Using SST, remove the manual transmission extension housing oil seal from the extension housing.

    SST
    09308-00010  



13. REMOVE BEARING RETAINER FRONT (MTM)


    D029148
  1. Remove the 8 bolts.

  1. w/o Gasket:

    1. Remove the bearing retainer from the transmission case.

  1. w/ Gasket:

    1. Remove the bearing retainer front and transmission front bearing retainer gasket from the manual transmission case.



14. REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL


    D033559
  1. Using a screwdriver, remove the transmission front bearing retainer oil seal from the bearing retainer front.



15. REMOVE FRONT BEARING SHAFT SNAP RING


    C086368
  1. Using a snap ring expander, remove the front bearing shaft snap ring from the manual transmission case.



16. REMOVE COUNTER GEAR FRONT BEARING SNAP RING NO.1


    C086369
  1. Using a snap ring expander, remove the counter gear front bearing snap ring No.1 from the manual transmission case.



17. REMOVE MANUAL TRANSMISSION CASE


    C086370
  1. Stand the manual transmission assembly as shown in the illustration.

  1. Using a plastic hammer, carefully tap off the manual transmission case.

  1. Remove the manual transmission case from the intermediate plate as shown in the illustration.



18. FIX INTERMEDIATE PLATE


    C086371
  1. Fix the intermediate plate in a vise.



19. REMOVE SHIFT DETENT BALL


    C086372
  1. Using a "torx" socket wrench T40, remove the 3 shift detent ball spring seats No.1 from the intermediate plate.



    C086373
  1. Using a magnetic finger, remove the 3 compression springs and 3 shift detent balls from the intermediate plate.



20. REMOVE SHIFT DETENT BALL NO.2


    C086374
  1. Using a "torx" socket wrench T40, remove the shift detent ball spring seat No.2 from the intermediate plate.



    C086375
  1. Using a magnetic finger, remove the compression spring and shift detent ball No.2 from the intermediate plate.



21. REMOVE GEAR SHIFT FORK SHAFT NO.4


    C086376
  1. Remove the shift fork bolt from the gear shift fork No.3.



    C114088
  1. Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the reverse shift head.



    C114089
  1. Using 2 screwdrivers and a hammer, remove the shaft snap ring from the gear shift fork shaft No.4

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    C114090
  1. Remove the ball from the intermediate plate.



    C114091
  1. Remove the gear shift fork shaft No.4 and reverse shift fork ball.



22. REMOVE REVERSE SHIFT HEAD


    C114281
  1. Remove the reverse shift head from the reverse shift fork shaft.



23. REMOVE GEAR SHIFT HEAD NO.3


    C114094
  1. Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the gear shift head No.3.

  1. Remove the gear shift head from the reverse shift fork shaft.



24. REMOVE SHIFT INTER LOCK PIN NO.2


    C114093
  1. Using a magnetic finger, remove shift inter lock pin No.2 from the reverse shift fork shaft.



25. REMOVE REVERSE SHIFT FORK SHAFT


    C114095
  1. Remove the reverse shift fork shaft, ball and compression spring.

    NOTICE:
    Cover the hole with a shop rag to prevent the ball from popping out.



26. REMOVE SHIFT INTER LOCK PIN NO.1


    C086389
  1. Using a magnetic finger, remove the shift inter lock pin No.1 from the intermediate plate.



27. REMOVE SHIFT INTER LOCK PIN NO.2


    C086390
  1. Using a magnetic finger, remove shift inter lock pin No.2 from the gear shift fork shaft No.2.



28. REMOVE GEAR SHIFT FORK SHAFT NO.2


    C086391
  1. Using a pin punch and a hammer, remove the slotted spring pin from the gear shift fork No.2.



    C086392
  1. Remove the shift fork shaft snap ring from the gear shift fork shaft No.2.



    C086393
  1. Remove the gear shift fork shaft No.2 from the intermediate plate.



29. REMOVE SHIFT INTER LOCK PIN NO.1


    C086394
  1. Using a magnetic finger, remove shift inter lock pin No.1 from the intermediate plate.



30. REMOVE GEAR SHIFT FORK SHAFT NO.1


    C086395
  1. Remove the shift fork bolt from the gear shift fork No.1.



    C086396
  1. Remove the gear shift fork shaft No.1 assembly and gear shift fork No.1 from the intermediate plate.



    C086397
  1. Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the gear shift head No.1.

  1. Remove the gear shift head No.1 from the gear shift fork shaft No.1.



31. REMOVE GEAR SHIFT FORK NO.2


    C086398
  1. Remove the gear shift fork No.2 from the transmission hub sleeve No.2.



32. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE


    C086399
  1. Using a feeler gauge, measure the counter shaft 5th gear thrust clearance.

    Standard clearance:
    0.125 to 0.325 mm (0.0049 to 0.0128 in.)

    Maximum clearance:
    0.325 mm (0.0128 in.)



33. REMOVE COUNTER SHAFT 5TH GEAR


    D033537
  1. Using 2 screwdrivers and a hammer, tap out the counter gear rear shaft snap ring from the counter gear.



    D033538E01
  1. Using SST, remove the gear spline piece No.5 and synchronizer ring No.3 from the counter gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



    D033539
  1. Remove the counter shaft 5th gear assembly and counter 5th gear bearing from the counter gear.



34. REMOVE 5TH GEAR THRUST WASHER


    D033540
  1. Remove the 5th gear thrust washer from the counter gear.



    D033541
  1. Using a magnetic finger, remove the 5th gear bearing inner race lock ball from the counter gear.



35. REMOVE REVERSE SHIFT ARM BRACKET


    D033529
  1. Remove the 2 bolts and reverse shift arm bracket with the shift arm from the intermediate plate.



36. REMOVE REVERSE SHIFT ARM


    D033309
  1. Using a screwdriver, remove the E-ring.

  1. Remove the shift fork from the shift arm.



37. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY


    D033542
  1. Remove the bolt and reverse idler gear shaft stopper from the intermediate plate.



    D033543
  1. Remove the the reverse idler gear shaft and reverse idler gear sub-assembly from the intermediate plate.



38. INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE


    C086408
  1. Using a dial indicator, inspect the reverse idler gear radial clearance.

    Standard clearance:
    0.04 to 0.08 mm (0.0016 to 0.0031 in.)

    Maximum clearance:
    0.13 mm (0.0051 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear.



39. INSPECT REVERSE IDLER GEAR SUB-ASSEMBLY


    D033607E01
  1. Using a feeler gauge, measure the clearance between the reverse idler gear and reverse shift arm.

    Standard clearance:
    0.05 to 0.35 mm (0.0020 to 0.0138 in.)

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear and reverse shift arm.



40. REMOVE OUTPUT SHAFT REAR BEARING (MTM) RETAINER


    D033544
  1. Using a "torx" socket wrench T40, remove the 4 screws and output shaft rear bearing retainer from the intermediate plate.



41. REMOVE COUNTER GEAR


    D029185
  1. Using a snap ring expander, remove the snap ring from the counter shaft center bearing.



    D033545E01
  1. Using SST, remove the counter shaft center bearing and the counter gear assembly from the intermediate plate.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04010, 09954-04010, 09955-04011, 09958-04011)



42. REMOVE INPUT SHAFT ASSEMBLY


    C086413
  1. Remove the input shaft assembly with the 13 input shaft bearings and synchronizer ring No.1 from the output shaft.



43. REMOVE OUTPUT SHAFT ASSEMBLY


    D033546
  1. Using a snap ring expander, remove the output shaft bearing snap ring from the output shaft assembly.



    D033547
  1. Remove the output shaft assembly from the intermediate plate by pulling on the output shaft assembly and tapping on the intermediate plate with a plastic hammer.