OUTPUT SHAFT > DISASSEMBLY |
| 1. INSPECT 1ST GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance.
| 2. INSPECT 2ND GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance.
| 3. INSPECT 3RD GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the thrust clearance.
| 4. INSPECT 1ST GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance.
| 5. INSPECT 2ND GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance.
| 6. INSPECT 3RD GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance.
| 7. REMOVE SPEEDOMETER DRIVE (MTM) GEAR |
![]() |
Using a snap ring expander, remove the snap ring.
Remove the drive gear.
Using a magnetic finger, remove the ball.
Using a snap ring expander, remove the snap ring.
| 8. REMOVE 1ST GEAR |
![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring from the output shaft.
![]() |
Using SST and a press, press out the 5th gear, center bearing, 1st gear, 1st gear needle roller bearing, and 1st gear bearing inner race from the output shaft.
| 9. REMOVE SYNCHRONIZER RING NO.1 (for 1st Gear) |
![]() |
Remove the synchronizer ring No.1 (for the 1st gear) from the clutch hub No.1.
| 10. REMOVE 1ST GEAR BEARING INNER RACE LOCK KEY OR BALL |
![]() |
Using a magnetic finger, remove the lock ball.
| 11. REMOVE 2ND GEAR |
![]() |
Using SST and a press, press out the clutch hub No.1, reverse gear, synchronizer ring No.1 and 2nd gear.
| 12. REMOVE SYNCHRONIZER RING NO.1 (for 2nd Gear) |
![]() |
Remove the synchronizer ring No.1 (for the 2nd gear) from the 2nd gear.
| 13. REMOVE 2ND GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the needle roller bearing from the output shaft.
| 14. REMOVE TRANSMISSION CLUTCH HUB NO.1 |
![]() |
Remove the 2 synchromesh shifting key springs.
Remove the reverse gear and 3 synchromesh shifting keys from the transmission clutch hub.
| 15. REMOVE 3RD GEAR |
![]() |
Using a snap ring expander, remove the snap ring from the output shaft.
![]() |
Using a press, press out the clutch hub No.2 and 3rd gear.
| 16. REMOVE SYNCHRONIZER RING NO.2 |
![]() |
Remove the synchronizer ring from the 3rd gear.
| 17. REMOVE 3RD GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the needle roller bearing form the output shaft.
| 18. REMOVE TRANSMISSION CLUTCH HUB NO.2 |
![]() |
Remove the 2 synchromesh shifting key springs.
Remove the transmission hub sleeve and 3 synchromesh shifting keys from the transmission clutch hub.
| 19. INSPECT OUTPUT SHAFT |
![]() |
Using a micrometer, measure the outside diameter of the output shaft journal surface.
![]() |
Using a micrometer, measure the flange thickness.
| 20. INSPECT 1ST GEAR BEARING INNER RACE |
![]() |
Using a micrometer, measure the inner race thickness.
![]() |
Using a micrometer, measure the outside diameter of the inner race.
| 21. INSPECT SYNCHRONIZER RING NO.1 (for 1st Gear) |
![]() |
Apply gear oil to the 1st gear cone. Press the synchronizer ring against the 1st gear cone and check that the synchronizer ring does not turn in the directions shown in the illustration.
If it turns, replace the synchronizer ring.
![]() |
Using a feeler gauge, measure the clearance between the synchronizer ring No.1 back and 1st gear spline end.
| 22. INSPECT SYNCHRONIZER RING NO.1 (for 2nd Gear) |
![]() |
Apply gear oil to the 2nd gear cone. Press the synchronizer ring against the 2nd gear cone and check that the synchronizer ring does not turn in the directions shown in the illustration.
If it turns, replace the synchronizer ring.
![]() |
Using a feeler gauge, measure the clearance between the synchronizer ring No.1 back and 2nd gear spline end.
| 23. INSPECT SYNCHRONIZER RING NO.2 |
![]() |
Apply gear oil to the 3rd gear cone. Press the synchronizer ring against the 3rd gear cone and check that the synchronizer ring does not turn in the directions shown in the illustration.
If it turns, replace the synchronizer ring.
![]() |
Using a feeler gauge, measure the clearance between the synchronizer ring No.2 back and 3rd gear spline end.
| 24. INSPECT REVERSE GEAR |
![]() |
Using vernier calipers, measure the clearance between the reverse gear and gear shift fork No.1.
![]() |
Check that the transmission clutch hub No.1 and reverse gear slide smoothly.
Check that the spline gear's edges of the reverse gear are not worn down.
| 25. INSPECT TRANSMISSION HUB SLEEVE NO.2 |
![]() |
Using vernier calipers, measure the hub sleeve No.2 and gear shift fork No.2 as shown in the illustration.
![]() |
Check the sliding condition between the hub sleeve No.2 and clutch hub No.2.
Check that the spline gear's edges of the transmission hub sleeve No.2 are not worn down.
| 26. INSPECT 1ST GEAR |
![]() |
Using a cylinder gauge, measure the inside diameter of the 1st gear.
| 27. INSPECT 2ND GEAR |
![]() |
Using a cylinder gauge, measure the inside diameter of the 2nd gear.
| 28. INSPECT 3RD GEAR |
![]() |
Using a cylinder gauge, measure the inside diameter of the 3rd gear.