Home › TRANSMISSION ยท G55 MANUAL TRANSMISSION › OUTPUT SHAFT

OUTPUT SHAFT > REASSEMBLY

for Preparation Click here



1. INSTALL TRANSMISSION CLUTCH HUB NO.2


    C086574E01
  1. Coat the hub sleeve with gear oil, and install it to the clutch hub.

    NOTICE:
    Be sure to set the hub sleeve to the clutch hub in the correct direction.



    C086575
  1. Install the 3 synchromesh shifting keys to the clutch hub with the 2 synchromesh shifting key springs.

    HINT:
    Do not set the openings of the shifting key springs in the same position.



2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING


    C086556
  1. Coat the needle roller bearing with gear oil, and install it to the output shaft.



3. INSTALL 3RD GEAR


    C086577
  1. Coat the 3rd gear with gear oil, and install it to the output shaft.



4. INSTALL SYNCHRONIZER RING NO.2


    C086576
  1. Coat the synchronizer ring with gear oil, and install it to the 3rd gear.



5. INSTALL TRANSMISSION CLUTCH HUB NO.2


    C086578
  1. Using SST and a press, press in the clutch hub No.2 to the output shaft.

    SST
    09316-60011   (09316-00021)



    C086579
  1. Select a clutch hub shaft snap ring that will allow the minimum amount of axial play.

    Standard clearance:
    0.1 mm (0.039 in.) or less

    Clutch hub shaft snap ring thickness: 
    Mark
    Thickness: mm (in.)
    C-1
    1.75 to 1.80 (0.0689 to 0.0709)
    D
    1.80 to 1.85 (0.0709 to 0.0728)
    D-1
    1.85 to 1.90 (0.0728 to 0.0748)
    E
    1.90 to 1.95 (0.0748 to 0.0768)
    E-1
    1.95 to 2.00 (0.0768 to 0.0787)
    F
    2.00 to 2.05 (0.0787 to 0.0807)
    F-1
    2.05 to 2.10 (0.0807 to 0.0827)



    C086553
  1. Using a snap ring expander, install the snap ring.



6. INSPECT 3RD GEAR THRUST CLEARANCE


    C086580
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)



7. INSTALL TRANSMISSION CLUTCH HUB NO.1


    C086581E01
  1. Coat the reverse gear with gear oil, and install it to the clutch hub.

    NOTICE:
    Be sure to set the reverse gear to the clutch hub in the correct direction.



    C086575
  1. Install 3 synchromesh shifting keys to the clutch hub with the 2 synchromesh shifting key springs.

    HINT:
    Do not set the openings of the shifting key springs in the same position.



8. INSTALL 2ND GEAR NEEDLE ROLLER BEARING


    C086582
  1. Coat the needle roller bearing with gear oil, and install it to the output shaft.



9. INSTALL 2ND GEAR


    C086583
  1. Coat the 2nd gear with gear oil, and install it to the output shaft.



10. INSTALL SYNCHRONIZER RING NO.1 (for 2nd Gear)


    C086584
  1. Coat the synchronizer ring No.1 with gear oil, and install it to the 2nd gear.



11. INSTALL TRANSMISSION CLUTCH HUB NO.1


    C086585E01
  1. Using SST and a press, press in the clutch hub to the output shaft.

    SST
    09316-60011   (09316-00021)



12. INSPECT 2ND GEAR THRUST CLEARANCE


    Z003552E02
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)



13. INSTALL SYNCHRONIZER RING NO.1 (for 1st Gear)


    C086587
  1. Coat the synchronizer ring with gear oil, and install it to the clutch hub No.1.



14. INSTALL 1ST GEAR BEARING INNER RACE LOCK KEY OR BALL


    C086588
  1. Coat the lock ball with gear oil, and install it to the output shaft.



15. INSTALL 1ST GEAR BEARING INNER RACE


    C086589
  1. Coat the needle roller bearing with gear oil.

  1. Install the inner lace and the needle roller bearing to the 1st gear.



16. INSTALL 1ST GEAR


    C086590
  1. Coat the 1st gear with gear oil, and install it to the output shaft.



17. INSTALL OUTPUT SHAFT CENTER BEARING


    C086591E01
  1. Using SST and a press, press in the center bearing to the output shaft.

    SST
    09316-60011   (09316-00021)



18. INSPECT 1ST GEAR THRUST CLEARANCE


    Z003552E01
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)



19. INSTALL 5TH GEAR


    C086593E01
  1. Using SST and a press, press in the 5th gear to the output shaft.

    SST
    09316-60011   (09316-00021)



    D033312
  1. Select a snap ring that will allow minimal axial play.

    Standard clearance:
    0.1 mm (0.039 in.) or less

    Output shaft bearing shaft snap ring 
    Mark
    Thickness: mm (in.)
    A
    2.67 to 2.72 (0.1051 to 0.1071)
    B
    2.73 to 2.78 (0.1075 to 0.1094)
    C
    2.79 to 2.84 (0.1098 to 0.1118)
    D
    2.85 to 2.90 (0.1122 to 0.1141)
    E
    2.91 to 2.96 (0.1146 to 0.1165)
    F
    2.97 to 3.02 (0.1169 to 0.1189)
    G
    3.03 to 3.08 (0.1193 to 0.1213)
    H
    3.09 to 3.14 (0.1217 to 0.1236)
    J
    3.15 to 3.20 (0.1240 to 0.1260)
    K
    3.21 to 3.26 (0.1264 to 0.1283)
    L
    3.27 to 3.32 (0.1287 to 0.1307)



    D033313
  1. Using a screwdriver and hammer, tap in the snap ring.



20. INSTALL SPEEDOMETER DRIVE (MTM) GEAR


    G034243
  1. Using a snap ring expander, install the snap ring.

  1. Install the ball.

  1. Install the drive gear.

  1. Using a snap ring expander, install the snap ring.



21. INSPECT 3RD GEAR RADIAL CLEARANCE


    C086543
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.008 to 0.0034 mm (0.0003 to 0.00134 in.)

    If the clearance is not as specified, replace the 3rd gear needle roller bearing.



22. INSPECT 2ND GEAR RADIAL CLEARANCE


    C086542
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.008 to 0.0034 mm (0.0003 to 0.00134 in.)

    If the clearance is not as specified, replace the 2nd gear needle roller bearing.



23. INSPECT 1ST GEAR RADIAL CLEARANCE


    C086541
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.009 to 0.056 mm (0.0004 to 0.0022 in.)

    If the clearance is not as specified, replace the 1st gear needle roller bearing.