Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0095/23    Intake Air Temperature Sensor 2 Circuit

DTC    P0097/23    Intake Air Temperature Sensor 2 Circuit Low

DTC    P0098/23    Intake Air Temperature Sensor 2 Circuit High

for Preparation Click here


DESCRIPTION

The diesel turbo Intake Air Temperature (IAT) sensor is built into the charge air cooler and senses the IAT. A built-in thermistor of the sensor changes the resistance value according to the intake air temperature. The lower the IAT is the greater the thermistor resistance value becomes, and the higher the temperature is the lower the resistance value becomes (see Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve the driveability with a cold engine.
G036559E03

DTC No.
DTC Detection Condition
Trouble Area
P0095/23
Open or short in diesel turbo IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in diesel turbo IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM
P0097/23
Short in diesel turbo IAT sensor circuit for 0.5 seconds
(sensor resistance value less than 25 Ω [sensor output voltage less than 0.05 V])
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM
P0098/23
Open in diesel turbo IAT sensor circuit for 0.5 seconds
(sensor resistance value more than 156 kΩ [sensor output voltage more than 4.9 V])
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM

WIRING DIAGRAM


A110950E03


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
Before starting the diagnostic procedures, check if the intelligent tester Data List's "Intake Air Temp (Turbo)" is displayed. Enter the following the menus: Powertrain / Engine / Data List.


Result:

Tester Displayed
Proceed to
"Intake Air Temp (Turbo)" is displayed
"When using intelligent tester" diagnostic procedures
"Intake Air Temp (Turbo)" is not displayed
"When not using intelligent tester" diagnostic procedures


When using intelligent tester:

1.READ VALUE OF INTELLIGENT TESTER (DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    OK:
    Same value as the actual intake air temperature.


    Result:

    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    OK (same as air temperature near to intake manifold)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or more.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)


    A099828E01
  1. Disconnect the D49 diesel turbo IAT sensor connector.

  1. Connect terminals 1 and 2 of the diesel turbo IAT sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the values.

    Standard:
    140°C (284°F) or more.



OK
CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR
NG


3.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)


    A099829E01
  1. Disconnect the D49 diesel turbo IAT sensor connector.

  1. Connect terminals THIA and E2 of the D1 ECM connector.

    HINT:
    Before checking, perform a visual and contact pressure check on the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the values.

    Standard:
    140°C (284°F) or more.



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

CONFIRM GOOD CONNECTION AT ECM. IF OK, REPLACE ECM 

4.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)


    A083863E05
  1. Disconnect the D49 diesel turbo IAT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the values.

    Standard:
    -40°C (-40°F) or more.



OK
REPLACE DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR
NG


5.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)


    A099830E01
  1. Disconnect the D49 diesel turbo IAT sensor connector.

  1. Disconnect the D1 ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the values.

    Standard:
    -40°C (-40°F) or more.



OK
CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR
NG

REPLACE ECM 


When not using intelligent tester:

1.CHECK ECM TERMINAL VOLTAGE (THIA - E2 TERMINALS)


    A053763E38
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D1-20 (THIA) - D1-28 (E2)
    20°C (68°F)
    0.5 to 3.4 V



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.INSPECT DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR


    A099921E02
  1. Remove the diesel turbo IAT sensor.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Connection
    Specified Condition
    20°C (68°F)
    2.16 to 2.17 kΩ

    NOTICE:
    If checking the IAT sensor in the water, keep the terminals dry. After the checking, wipe the sensor dry.



NG
REPLACE DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR
OK


3.CHECK HARNESS AND CONNECTOR (ECM - DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR)


    A096606E03
  1. Disconnect the D49 diesel turbo IAT sensor connector.

  1. Disconnect the D1 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D1-20 (THIA) - D49-2
    Below 1 Ω
    D1-28 (E2) - D49-1
    Below 1 Ω
    D1-20 (THIA) or D49-2 - Body ground
    10 kΩ or higher
    D1-28 (E2) or D49-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM