OUTPUT SHAFT > INSPECTION |
| 1. INSPECT 1ST GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance of the 1st gear.
| 2. INSPECT 2ND GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance of the 2nd gear.
| 3. INSPECT 3RD GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the thrust clearance of the 3rd gear.
| 4. INSPECT 1ST GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 1st gear.
| 5. INSPECT 2ND GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 2nd gear.
| 6. INSPECT 3RD GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 3rd gear.
| 7. INSPECT OUTPUT SHAFT |
![]() |
Using a dial indicator, measure the runout of the output shaft.
![]() |
Using a micrometer, measure the outer diameter of the output shaft at points A, B and C.
![]() |
Using a micrometer, measure the thickness of the output shaft flange as shown in the illustration.
| 8. INSPECT 3RD GEAR |
![]() |
Using a cylinder gauge, measure the inner diameter of the 3rd gear.
| 9. INSPECT 2ND GEAR |
![]() |
Using a cylinder gauge, measure the inner diameter of the 2nd gear.
| 10. INSPECT 1ST GEAR |
![]() |
Using a cylinder gauge, measure the inner diameter of the 1st gear.
| 11. INSPECT 1ST GEAR THRUST WASHER |
![]() |
Using a micrometer, measure the thickness of the 1st gear thrust washer.
| 12. INSPECT SYNCHRONIZER RING NO.1 (for 1st Gear (2TR-FE)) |
![]() |
Apply gear oil to the cone of the 1st gear, and check that it does not turn in either direction while pushing the synchronizer ring No.1 (for the first synchronizer ring).
If it turns, replace the synchronizer ring No.1.
![]() |
Measure the clearance between the synchronizer ring No.1 and 1st gear while pushing the synchronizer ring No.1 against the cone of the 1st gear.
| 13. INSPECT SYNCHRONIZER RING SET NO.1 (for 1st Gear (2KD-FTV)) |
![]() |
Apply gear oil to the cone of the 1st gear, and check that it does not turn in either direction while pushing the synchronizer ring set No.1 (for the first synchronizer ring).
If it turns, replace the synchronizer ring set No.1.
![]() |
Measure the clearance between the synchronizer ring No.1 and 1st gear while pushing the synchronizer ring No.1 against the cone of the 1st gear.
| 14. INSPECT SYNCHRONIZER RING SET NO.1 (for 2nd Gear) |
![]() |
Apply gear oil to the cone of the 2nd gear, and check that it does not turn in either direction while pushing the synchronizer ring set No.1 (for the second synchronizer ring).
If it turns, replace the synchronizer ring set No.1.
![]() |
Measure the clearance between the synchronizer ring set No.1 (for the second synchronizer ring) and 2nd gear while pushing the synchronizer ring set No.1 against the cone of the 2nd gear.
| 15. INSPECT SYNCHRONIZER RING NO.2 (for 3rd Gear) |
![]() |
Apply gear oil to the cone of the 3rd gear, and check that it does not turn in either direction while pushing the synchronizer ring No.2 (for the third synchronizer ring).
If it turns, replace the synchronizer ring No.2.
![]() |
Check the clearance between the synchronizer ring No.2 (for the third synchronizer ring) and 3rd gear while pushing the synchronizer ring No.2 (for the second synchronizer ring) against the cone of the 3rd gear.
| 16. INSPECT REVERSE GEAR |
![]() |
Using vernier calipers, measure the width of the reverse gear groove and the thickness of the claw part on the gear shift fork No.1, and calculate the clearance.
| 17. INSPECT TRANSMISSION CLUTCH HUB NO.1 |
![]() |
Check that the transmission clutch hub No.1 and reverse gear slide smoothly each other.
Check the tip of the spline gear sleeve of the reverse gear for wear.
If there are any defects, replace the transmission clutch hub No.1.
| 18. INSPECT TRANSMISSION HUB SLEEVE NO.2 |
![]() |
Using vernier calipers, measure the width of the transmission hub No.2 groove and the thickness of the claw of the gear shift fork No.2.
| 19. INSPECT TRANSMISSION CLUTCH HUB NO.2 |
![]() |
Check the sliding condition between the transmission clutch hub No.2 and the transmission hub sleeve No.2.
Check the tip of the spline gear sleeve of the reverse gear for wear.