OUTPUT SHAFT > DISASSEMBLY |
| 1. INSPECT 1ST GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance of the 1st gear.
| 2. INSPECT 2ND GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance of the 2nd gear.
| 3. INSPECT 3RD GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the thrust clearance of the 3rd gear.
| 4. INSPECT 1ST GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 1st gear.
| 5. INSPECT 2ND GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 2nd gear.
| 6. INSPECT 3RD GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 3rd gear.
| 7. REMOVE 1ST GEAR |
![]() |
Using SST and a press, remove the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.
| 8. REMOVE SYNCHRONIZER RING NO.1 (for 1st Gear (2TR-FE)) |
![]() |
Remove the synchronizer ring No.1 from the output shaft.
| 9. REMOVE SYNCHRONIZER RING SET NO.1 (for 1st Gear (2KD-FTV)) |
![]() |
Remove the synchronizer ring set No.1 from the output shaft.
| 10. REMOVE 1ST GEAR THRUST WASHER PIN |
![]() |
Remove the 1st gear thrust washer pin from the output shaft.
| 11. REMOVE 1ST GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the 1st gear needle roller bearing from the output shaft.
| 12. REMOVE 1ST GEAR BEARING SPACER |
![]() |
Remove the 1st gear bearing spacer from the output shaft.
| 13. REMOVE BEARING SHAFT SNAP RING |
![]() |
Using 2 screwdrivers and a hammer, remove the bearing shaft snap ring from the output shaft.
| 14. REMOVE 2ND GEAR |
![]() |
Using SST and a press, remove the transmission clutch hub No.1, reverse gear, synchronizer ring No.1 and 2nd gear from the output shaft.
| 15. REMOVE 2ND GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the 2nd gear needle roller bearing from the output shaft.
| 16. REMOVE REVERSE GEAR |
![]() |
Remove the reverse gear, 3 synchromesh shifting keys No.1 and 3 synchromesh shifting key springs.
Use a shop rag to prevent the shifting keys and the shifting key springs from popping out.
| 17. REMOVE CLUTCH HUB SET SHAFT SNAP RING |
![]() |
Using snap ring pliers, remove the clutch hub set shaft snap ring from the output shaft.
| 18. REMOVE 3RD GEAR |
![]() |
Using SST and a press, remove the clutch hub No.2 with the hub sleeve No.2, synchronizer ring No.2 and 3rd gear from the output shaft.
| 19. REMOVE 3RD GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the 3rd gear needle roller bearing from the output shaft.
| 20. REMOVE TRANSMISSION HUB SLEEVE NO.2 |
![]() |
Remove the transmission hub sleeve No.2, 3 synchromesh shifting key springs and 3 synchromesh shifting keys No.2 from the transmission clutch hub No.2.
| 21. INSPECT OUTPUT SHAFT |
![]() |
Using a dial indicator, measure the runout of the output shaft.
![]() |
Using a micrometer, measure the outer diameter of the output shaft at points A, B and C.
![]() |
Using a micrometer, measure the thickness of the output shaft flange as shown in the illustration.
| 22. INSPECT 3RD GEAR |
![]() |
Using a cylinder gauge, measure the inner diameter of the 3rd gear.
| 23. INSPECT 2ND GEAR |
![]() |
Using a cylinder gauge, measure the inner diameter of the 2nd gear.
| 24. INSPECT 1ST GEAR |
![]() |
Using a cylinder gauge, measure the inner diameter of the 1st gear.
| 25. INSPECT 1ST GEAR THRUST WASHER |
![]() |
Using a micrometer, measure the thickness of the 1st gear thrust washer.
| 26. INSPECT SYNCHRONIZER RING SET NO.1 (for 1st Gear (2KD-FTV)) |
![]() |
Apply gear oil to the cone of the 1st gear, and check that it does not turn in either direction while pushing the synchronizer ring set No.1 (for the first synchronizer ring).
If it turns, replace the synchronizer ring set No.1.
![]() |
Measure the clearance between the synchronizer ring No.1 and 1st gear while pushing the synchronizer ring No.1 against the cone of the 1st gear.
| 27. INSPECT SYNCHRONIZER RING NO.1 (for 1st Gear (2TR-FE)) |
![]() |
Apply gear oil to the cone of the 1st gear, and check that it does not turn in either direction while pushing the synchronizer ring No.1 (for the first synchronizer ring).
If it turns, replace the synchronizer ring No.1.
![]() |
Measure the clearance between the synchronizer ring No.1 and 1st gear while pushing the synchronizer ring No.1 against the cone of the 1st gear.
| 28. INSPECT SYNCHRONIZER RING SET NO.1 (for 2nd Gear) |
![]() |
Apply gear oil to the cone of the 2nd gear, and check that it does not turn in either direction while pushing the synchronizer ring set No.1 (for the second synchronizer ring).
If it turns, replace the synchronizer ring set No.1.
![]() |
Measure the clearance between the synchronizer ring set No.1 (for the second synchronizer ring) and 2nd gear while pushing the synchronizer ring set No.1 against the cone of the 2nd gear.
| 29. INSPECT SYNCHRONIZER RING NO.2 (for 3rd Gear) |
![]() |
Apply gear oil to the cone of the 3rd gear, and check that it does not turn in either direction while pushing the synchronizer ring No.2 (for the third synchronizer ring).
If it turns, replace the synchronizer ring No.2.
![]() |
Check the clearance between the synchronizer ring No.2 (for the third synchronizer ring) and 3rd gear while pushing the synchronizer ring No.2 (for the second synchronizer ring) against the cone of the 3rd gear.
| 30. INSPECT REVERSE GEAR |
![]() |
Using vernier calipers, measure the width of the reverse gear groove and the thickness of the claw part on the gear shift fork No.1, and calculate the clearance.
| 31. INSPECT TRANSMISSION CLUTCH HUB NO.1 |
![]() |
Check that the transmission clutch hub No.1 and reverse gear slide smoothly each other.
Check the tip of the spline gear sleeve of the reverse gear for wear.
If there are any defects, replace the transmission clutch hub No.1.
| 32. INSPECT TRANSMISSION HUB SLEEVE NO.2 |
![]() |
Using vernier calipers, measure the width of the transmission hub No.2 groove and the thickness of the claw of the gear shift fork No.2.
| 33. INSPECT TRANSMISSION CLUTCH HUB NO.2 |
![]() |
Check the sliding condition between the transmission clutch hub No.2 and the transmission hub sleeve No.2.
Check the tip of the spline gear sleeve of the reverse gear for wear.