OUTPUT SHAFT > REASSEMBLY |
| 1. INSTALL TRANSMISSION HUB SLEEVE NO.2 |
![]() |
Install the 3 synchromesh shifting key springs and the 3 synchromesh shifting keys No.2 to the transmission clutch hub No.2.
Apply gear oil to the sliding part of the transmission hub sleeve No.2, and install it onto the transmission clutch hub No.2.
| 2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING |
![]() |
Apply gear oil to the 3rd gear needle roller bearing, and install it onto the output shaft.
| 3. INSTALL 3RD GEAR |
![]() |
Apply gear oil to the 3rd gear, and install it onto the output shaft.
| 4. INSTALL SYNCHRONIZER RING NO.2 (for 3rd Gear) |
![]() |
Apply gear oil to the synchronizer ring No.2, and install it onto the 3rd gear.
| 5. INSTALL TRANSMISSION CLUTCH HUB NO.2 |
![]() |
Using SST, install the transmission clutch hub No.2 onto the output shaft.
![]() |
Select a clutch hub set shaft snap ring so that the clearance between the transmission clutch hub No.2 and shaft snap ring is within the specified values. Then install it onto the output shaft.
| Mark | Thickness mm (in.) |
| A | 1.80 to 1.85 mm (0.0709 to 0.0728 in.) |
| B | 1.85 to 1.90 mm (0.0728 to 0.0748 in.) |
| C | 1.90 to 1.95 mm (0.0748 to 0.0768 in.) |
| D | 1.95 to 2.00 mm (0.0768 to 0.0787 in.) |
| E | 2.00 to 2.05 mm (0.0787 to 0.0807 in.) |
| F | 2.05 to 2.10 mm (0.0807 to 0.0827 in.) |
| G | 2.10 to 2.15 mm (0.0827 to 0.0846 in.) |
| 6. INSTALL 2ND GEAR NEEDLE ROLLER BEARING |
![]() |
Apply gear oil to the 2nd gear needle roller bearing, and install it onto the output shaft.
| 7. INSTALL 2ND GEAR |
![]() |
Apply gear oil to the 2nd gear, and install it onto the output shaft.
| 8. INSTALL SYNCHRONIZER RING SET NO.1 (for 2nd Gear) |
![]() |
Apply gear oil to the synchronizer ring set No.1, and install it onto the 2nd gear.
| 9. INSTALL REVERSE GEAR |
![]() |
Using a screwdriver, install the 3 synchromesh shifting key springs and 3 synchromesh shifting keys No.1 onto the transmission clutch hub No.1.
Apply gear oil to the reverse gear, and install it onto the transmission clutch hub No.1.
| 10. INSTALL TRANSMISSION CLUTCH HUB NO.1 |
![]() |
Using SST and a press, install the transmission clutch hub No.1 onto the output shaft.
![]() |
Select a bearing shaft snap ring so that the clearance between the transmission clutch hub No.1 and bearing shaft snap ring is within the specified values. Then install it onto the output shaft.
| Mark | Thickness mm (in.) |
| A | 2.30 to 2.35 mm (0.0906 to 0.0925 in.) |
| B | 2.35 to 2.40 mm (0.0925 to 0.0945 in.) |
| C | 2.40 to 2.45 mm (0.0945 to 0.0965 in.) |
| D | 2.45 to 2.50 mm (0.0965 to 0.0984 in.) |
| E | 2.50 to 2.55 mm (0.0984 to 0.1004 in.) |
| F | 2.55 to 2.60 mm (0.1004 to 0.1024 in.) |
| G | 2.60 to 2.65 mm (0.1024 to 0.1043 in.) |
| 11. INSTALL 1ST GEAR BEARING SPACER |
![]() |
Apply gear oil to the 1st gear bearing spacer, and install it onto the output shaft.
| 12. INSTALL 1ST GEAR NEEDLE ROLLER BEARING |
![]() |
Apply gear oil to the 1st gear needle roller bearing, and install it onto the output shaft.
| 13. INSTALL 1ST GEAR THRUST WASHER PIN |
![]() |
Install the 1st gear thrust washer pin onto the output shaft.
| 14. INSTALL SYNCHRONIZER RING NO.1 (for 1st Gear (2TR-FE)) |
![]() |
Apply gear oil to the synchronizer ring No.1, and install it onto the output shaft.
| 15. INSTALL SYNCHRONIZER RING SET NO.1 (for 1st Gear (2KD-FTV)) |
![]() |
Apply gear oil to the synchronizer ring set No.1, and install it to the 1st gear.
| 16. INSTALL 1ST GEAR |
![]() |
Apply gear oil to the 1st gear, and install it onto the output shaft.
| 17. INSTALL 1ST GEAR THRUST WASHER |
![]() |
Apply gear oil to the 1st gear thrust washer, and install it onto the output shaft.
| 18. INSTALL OUTPUT SHAFT CENTER BEARING |
![]() |
Using SST and a press, install a new output shaft center bearing onto the output shaft.
| 19. INSTALL 5TH GEAR |
![]() |
Using SST and a press, install the 5th gear onto the output shaft.
| 20. INSPECT 1ST GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance of the 1st gear.
| 21. INSPECT 2ND GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance of the 2nd gear.
| 22. INSPECT 3RD GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the thrust clearance of the 3rd gear.
| 23. INSPECT 1ST GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 1st gear.
| 24. INSPECT 2ND GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 2nd gear.
| 25. INSPECT 3RD GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance of the 3rd gear.