Part Tighten
| N*m
| kgf*cm
| ft.*lbf
|
Injection pump x Timing gear case
| 21
| 210
| 15
|
Injection pump x Injection pump stay
| 26
| 270
| 19
|
Compression gage attachment x Cylinder head
| 13
| 133
| 10
|
Generator x Engine
| Bolt A
| 75
| 765
| 55
|
Bolt B
| 18
| 185
| 13
|
Idler pulley x compressor mounting bracket
| 39
| 400
| 29
|
Vane pump x pump bracket
| Bolt A
| 48
| 489
| 35
|
Bolt B
| 64
| 635
| 47
|
Cylinder head cover sub-assembly x Cylinder head
| 12
| 120
| 9
|
Timing belt idler No.1 x Timing gear case
| 44
| 450
| 33
|
Crankshaft pulley x Crank shaft
| 235
| 2,400
| 173
|
Vane pump drive pulley x Crankshaft pulley
| 18
| 184
| 13
|
Camshaft bearing cap x Cylinder head
| 25
| 255
| 18
|
Camshaft Oil seal retainer x Cylinder block
| 18
| 185
| 13
|
Timing belt No.2 cover x Cylinder head
| 18
| 185
| 13
|
Camshaft timing pulley x camshaft
| 98
| 1,000
| 72
|
Cylinder head x cylinder block
| 1st
| 78
| 800
| 58
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
3rd
| Turn 90°
| Turn 90°
| Turn 90°
|
Rear end plate x Cylinder block
| 27
| 275
| 19
|
Flywheel sub-assembly x Crankshaft
| 123
| 1,250
| 90
|
Engine hanger No.2 x Cylinder head
| 37
| 380
| 27
|
Engine oil pressure switch x Cylinder block
| 15
| 155
| 11
|
Exhaust manifold x Cylinder head
| 52
| 530
| 38
|
Exhaust manifold heat insulator No.1 x Exhaust manifold
| Bolt A
| 18
| 185
| 13
|
Bolt B
| 19
| 195
| 14
|
Engine mounting bracket front No.1 RH x Cylinder block
| 49
| 500
| 36
|
Pump bracket x Cylinder block
| Bolt A
| 78
| 795
| 58
|
Bolt B
| 57
| 581
| 42
|
Engine oil level sensor x Oil pan
| 7.0
| 71
| 62
|
Cylinder block water drain cock sub-assembly x Cylinder block
| 57
| 581
| 42
|
Water by-pass hose union x Timing gear case sub assembly
| 39
| 400
| 29
|
Water outlet housing x Cylinder head
| 19
| 195
| 14
|
Intake air connector bracket x Cylinder head
| 18
| 184
| 13
|
Compressor mounting bracket x Cylinder head
| 85
| 870
| 63
|
Engine mounting bracket front No.1 RH x Compressor mounting bracket
| 47
| 475
| 36
|
Fan belt adjusting bar x Cylinder head
| 45
| 460
| 33
|
Engine mounting insulator front x Front suspension cross member
| 55
| 561
| 41
|
Vane pump pulley x Vane pump assembly
| 43
| 440
| 32
|
Front suspension cross member x Body
| Bolt A
| 36
| 367
| 27
|
Bolt B
| 39
| 398
| 29
|
Bolt C
| 150
| 1,530
| 111
|
Rear engine mounting x Body
| 98
| 1,000
| 72
|
Engine wire x J/B
| 9.8
| 100
| 87 in.*lbf
|
Engine rear oil seal retainer x Cylinder block
| 13
| 130
| 10
|
Timing gear case x Cylinder block
| 23
| 230
| 17
|
Oil strainer x Cylinder block
| 18
| 180
| 13
|
Oil strainer x Timing gear case
| 21
| 210
| 15
|
Oil pan x Cylinder block
| 18
| 180
| 13
|
Oil pan x Timing gear case
| 18
| 180
| 13
|
Oil pan x Engine rear oil seal retainer
| 18
| 180
| 13
|
Water pump x Timing gear case
| 23
| 230
| 17
|
Timing belt idler No.2 x Timing gear case
| 33
| 340
| 24
|
Timing belt idler No.1 x Timing gear case
| 12 mm head
| 19
| 195
| 14
|
Taper screw plug No.1 x Cylinder block
| 20
| 200
| 14
|
Water drain cock x Cylinder block
| 57
| 580
| 42
|
Cylinder block oil orifice x Cylinder block
| 11
| 110
| 8
|
Oil nozzle x Cylinder block
| 26
| 260
| 18
|
Crankshaft bearing cap x Cylinder block
| 105
| 1,050
| 77
|
Connecting rod cap x Connecting rod
| 1st
| 54
| 550
| 40
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|