2014-2019 Hiace · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jan 2017


1. INSTALL STARTER ARMATURE ASSEMBLY

  1. A202439
    Install the starter armature assembly to the starter yoke assembly.

    NOTICE:
    The magnet of the starter yoke assembly may attract the starter armature assembly when the starter armature assembly is installed, causing the magnet to break.


2. INSTALL STARTER BRUSH HOLDER ASSEMBLY

  1. A368710E01
    When installing a new part:

    NOTICE:
    Do not remove the retainer.

    Text in Illustration 
    *a
    Retainer

    1. A368711E01
      With the retainer installed, push the starter brush holder assembly onto the starter armature assembly.
      Text in Illustration 
      *1
      Starter Brush Holder Assembly
      *2
      Starter Armature Assembly
      *a
      Retainer
      *b
      Push Starter Brush Holder Assembly in this Direction
      *c
      Push Out Retainer in this Direction

      NOTICE:
      Be careful not to damage the brushes when pushing the starter brush holder assembly in place.

      HINT:
      Install the starter brush holder assembly as shown in the illustration, as the installation direction is fixed.

    2. Push the starter brush holder assembly onto the starter armature assembly while pushing out the retainer with the end of the starter armature assembly.

    3. A368712E01
      Push the starter brush holder assembly onto the starter armature assembly until the retainer is completely pushed out.
      Text in Illustration 
      *a
      Retainer
      *b
      Push Out Retainer in this Direction

  1. A372726E01
    When reinstalling:

    1. Set the spring inside the holder box. Then, push the brush inside the holder box in the orientation shown in the illustration.

      NOTICE:
      Install the holder boxes so the rounded corner of the rubber portion of the lead wire faces the holder plate.

      HINT:
      Install the holder boxes with their claws facing the holder plate.

      Text in Illustration 
      *a
      Holder Box
      *b
      Spring
      *c
      Brush
      *d
      Rubber Part
      *e
      Holder Plate
      *f
      Rounded Corner of Lead Wire Rubber Part

    2. A368714E01
      With the brush pushed inside, use wire or similar material to fix the brush in the position shown in the illustration.
      Text in Illustration 
      *a
      Range for Wire Used to Fix Brush
      *b
      Brush
      *c
      Holder Box
      *d
      1 mm or less
      *e
      Claw of the Holder Box

      NOTICE:
      1. When fixing the brush in place using wire or similar material, be careful not to damage the brush.
      2. Fix the brush in place so that it protrudes from the holder box by 1 mm or less.

    3. A368713E01
      Insert the claw of the holder box into the holder plate to fix the holder box in place.
      Text in Illustration 
      *a
      Holder Plate
      *b
      Rounded Corner of Lead Wire Rubber Part
      *c
      Claw of the Holder Box

      NOTICE:
      1. Install the holder boxes so the rounded corner of the rubber portion of the lead wire faces the holder plate.
      2. Check that the 4 claws of the holder boxes are fixed to the holder plate.

    4. A368715E01
      Push the starter brush holder assembly onto the starter armature assembly, but leave enough room to remove the wire or similar material.
      Text in Illustration 
      *1
      Starter Brush Holder Assembly
      *2
      Starter Armature Assembly
      *a
      Push Starter Brush Holder Assembly in this Direction
      *b
      Wire

    5. Remove the 4 pieces of wire or similar material and then push the starter brush holder assembly all the way onto the starter armature assembly.

      NOTICE:
      When removing the wire or similar material, be careful not to damage the brush.

  1. A377035E01
    Align the rubber part of the starter yoke assembly with the groove of the starter commutator end frame assembly.
    Text in Illustration 
    *a
    Rubber Part
    *b
    Starter Commutator End Frame Assembly

  1. Install the starter commutator end frame assembly with the 2 screws.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }


3. INSTALL STARTER YOKE ASSEMBLY
  1. Install the rubber seal to the repair service starter kit.

  1. A341322
    Apply high-temperature grease to the planetary gears and pins of the repair service starter kit as shown in the illustration.
    Text in Illustration 
    V100135
    High-temperature Grease

  1. Install the 3 planetary gears to the repair service starter kit.

  1. Install the starter armature plate to the starter yoke assembly.

  1. A224840E03
    Check that the notch of the starter armature plate fits over the protrusion of the starter yoke assembly.
    Text in Illustration 
    *a
    Protrusion
    *b
    Notch

  1. A341323E01
    Align the protrusion of the starter yoke assembly with the notches inside the repair service starter kit and insert the starter yoke assembly into the repair service starter kit.
    Text in Illustration 
    *a
    Notches
    *b
    Protrusion

  1. Using a T25 "TORX" socket wrench, install the repair service starter kit with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


4. INSTALL MAGNET STARTER SWITCH ASSEMBLY
  1. Apply high-temperature grease to the plunger hook of the magnet starter switch assembly.

  1. A341229
    Hang the plunger hook of the magnet starter switch assembly on the starter pinion drive lever from the upper side.

  1. Install the magnet starter switch assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the lead wire to terminal C with the nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

← INSPECTION (from Jan 2017)INSTALLATION (from Jan 2017) →