2014-2019 Hiace · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A115870E01
    Using SST and a press, press in a new bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A115871E01
    Align the claws of the bearing retainer with the grooves inside the drive end frame.

  1. Install the bearing retainer with the 4 screws.


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the rotor and washer to the drive end frame.

  1. Install the generator washer to the generator rotor assembly.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A102584E03
    Using deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.

  1. A102577
    Install the generator coil assembly with the 4 through bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A113845E04
    While pushing the 2 brushes to the inside of the generator brush holder assembly, insert a 1.0 mm (0.039 in.) pin into the generator brush holder hole.

  1. A079316E07
    Install the brush holder assembly with the 2 screws.

  1. Pull out the pin from the brush holder assembly.


5. INSTALL TERMINAL INSULATOR

  1. A102585
    Install the terminal insulator.


6. INSTALL GENERATOR REAR END COVER

  1. A102574
    Install the end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


7. INSTALL GENERATOR WITH CLUTCH PULLEY (w/ Clutch Pulley)
  1. Temporarily install the generator with clutch pulley by hand.

  1. Mount the generator in a vise between aluminum plates.

  1. A219550E03
    Install SST (A) and SST (B) to the generator with clutch pulley as shown in the illustration.
    SST
    09820-63021  

    NOTICE:
    Securely attach SST to the generator with clutch pulley and generator rotor shaft.

  1. A219552E03
    Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator with clutch pulley.

    Torque:
    without SST:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }
    with SST:
    63 N*m{ 642 kgf*cm , 46 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 380 mm (14.96 in.)
    2. Make sure SST and the wrench are connected in a straight line.

    NOTICE:
    Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

  1. Remove SST from the generator.

  1. Check that the generator with clutch pulley rotates smoothly.

  1. Install a new generator pulley cap.


8. INSTALL GENERATOR PULLEY (w/o Clutch Pulley)
  1. Install the pulley to the rotor shaft by tightening the generator pulley nut by hand.

  1. Install SST (1-A) and (1-B) to the rotor shaft.

    SST
    09820-63011   (09820-06010, 09820-06021)
    HINT: 
    SST (1-A) and (1-B)
    09820-06010
    SST 2
    09820-06021

  1. A075664E06
    Hold SST (1-A) with a torque wrench, and tighten SST (1-B) clockwise to the specified torque.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Check that the SST is secured to the generator rotor shaft.

  1. Mount the generator in a vise between aluminum plates.

  1. A243996E01
    Insert SST 2 and attach it to the generator pulley nut.

  1. A243998E01
    Tighten the generator pulley nut by turning SST (1- A) in the direction shown in the illustration.

    Torque:
    133 N*m{ 1351 kgf*cm , 98 ft.*lbf }

  1. Remove SST 2 from the generator.

  1. A075667E03
    Turn SST (1-A), and remove SST (1-A) and (1-B).

  1. Turn the generator pulley, and check that the generator pulley moves smoothly.

← INSPECTION (from Oct 2014)INSTALLATION (Oct 2014 – Mar 2016) →