2014-2019 Hiace · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. REMOVE FRONT WHEEL

2. SEPARATE FRONT SPEED SENSOR (w/ ABS)

  1. C102281E01
    Remove the 2 bolts, and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.


3. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

  1. C102283E01
    Remove the 2 bolts, and disconnect the brake caliper assembly.

    NOTICE:
    Use a wire or an equivalent to keep the brake caliper from hanging down by the flexible hose.


4. SEPARATE TIE ROD END SUB-ASSEMBLY
  1. Remove the cotter pin and castle nut.

  1. C102285E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Do not damage the brake dust cover.
    3. Make sure that the string of the SST is securely tied to the vehicle.


5. REMOVE FRONT AXLE ASSEMBLY

  1. C102287
    Remove the 4 bolts, 4 nuts and front axle assembly from the front suspension lower arm.

  1. Remove the cotter pin and castle nut.

  1. C102660E01
    Using SST, remove the front axle assembly from the front suspension upper arm.
    SST
    09628-62011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Apply grease to the threads and tip of the SST center bolt before use.
    3. Make sure that the string of the SST is securely tied to the vehicle.


6. REMOVE FRONT LOWER BALL JOINT ASSEMBLY
  1. Fix the steering knuckle in the vise using aluminium plates.

    NOTICE:
    Do not damage the steering knuckle.

  1. Remove the cotter pin.

  1. Loosen the nut.

  1. C194033E01
    Using SST, separate the front lower ball joint assembly from the steering knuckle.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Make sure that the string of the SST is securely tied to the steering knuckle.

  1. Remove the nut and front lower ball joint assembly.


7. REMOVE INNER KNUCKLE GREASE RETAINER CAP (w/ Cap)

  1. C194034
    Using a chisel, make a hole in the center of the outer knuckle grease retainer cap to insert a brass bar.

  1. C194035
    Using a brass bar, remove the inner knuckle grease retainer cap from the steering knuckle as shown in the illustration.


8. REMOVE OUTER KNUCKLE GREASE RETAINER CAP (w/ Cap)

  1. C194036E01
    Using SST, remove the outer knuckle grease retainer cap.
    SST
    09950-60010   (09951-00300)
    09950-70010   (09951-07200)


9. REMOVE STEERING KNUCKLE

  1. C103883E01
    Remove the 4 bolts.

  1. C304721E01
    Using SST, remove the steering knuckle, brake dust cover from the front axle hub sub-assembly.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04010, 09958-04011)
    09950-60010   (09951-00470)
    09955-04140  
    09958-04030  

    NOTICE:
    1. Apply grease to the threads and tip of the SST center bolt (09953-04010) before use.
    2. Make sure that the slide arm (09952-04010) is at a 90° angle to the hanger 200 (09951-04020) when using SST.
    3. Make sure that the claw No. 14 (09955-04140) is securely attached to the steering knuckle.

    HINT:
    For bolt A, use the bolt for the holder (09958-04011).

← COMPONENTS (from Oct 2014)INSTALLATION (Oct 2014 – Dec 2014) →