2014-2019 Hiace · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Apr 2016

Versions by build date: Oct 2014 – Mar 2016 from Apr 2016


1. INSTALL MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C102623E01
    Using SST and a hammer, install a new oil seal to the extension housing.
    SST
    09325-20010  

    Drive in depth:
    - 0.5 to 0.5 mm (-0.020 to 0.020 in.)

  1. Coat the lip of the oil seal with MP grease.


2. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller shaft assembly in the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. C102185E01
    Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }


3. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase)

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller with center bearing shaft assembly in the extension housing.

  1. C107214
    Install the center support bearing assembly No.1, and temporarily tighten the 2 bolts.

  1. C102185E01
    Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }

  1. C107213E01
    Check that the center line of the bracket is at right angles to the shaft axial direction.

  1. C115777E01
    Adjust the center support bearing assembly No.1.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing No.1 to maintain the angles, as shown.
    2. In the same conditions, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) of each other in the vehicle's longitudinal direction with the vehicle unladen.

  1. Tighten the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }


4. ADD MANUAL TRANSMISSION OIL

  1. D025304E01
    Park the vehicle in a level place.

  1. Remove the transmission filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.

    Oil grade:
    TOYOTA Genuine Manual Transmission Gear oil API GL-3 (GL-4) or equivalent
    Viscosity:
    Above -10°C (14°F): SAE 75W-90, 80W or 80W-90
    Below -10°C (14°F): SAE 75W-90
    Capacity:
    2.6 liters (2.7 US qts, 2.3 Imp. qts)

    NOTICE:
    1. Problems may occur when the oil level is too high or too low.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

← INSTALLATION (Oct 2014 – Mar 2016)COMPONENTS (from Oct 2014) →