2014-2019 Hiace · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017


1. INSTALL TRANSMISSION CONTROL CABLE BRACKET NO.1

  1. C112943
    Install the transmission control cable bracket No.1 with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }


2. INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY

  1. C102216
    Install the engine mounting insulator assembly rear with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


3. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

  1. C112945E01
    Install the transmission unit assembly with the 8 bolts.

    Torque:
    Bolt A:
    72 N*m{ 729 kgf*cm , 53 ft.*lbf }
    Bolt B:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }
    Bolt C:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. C102212
    Install the transmission unit assembly with the bolt, nut and 2 washers to the frame.

    Torque:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    1. Insert the bolt from the left side of the vehicle.
    2. Tighten the nut while holding the bolt.


4. INSTALL STARTER ASSEMBLY (for 2.2 kW Type)
  1. Install the starter with the 2 bolts and nut.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }

  1. Install the stay with the 2 bolts and nut.

    Torque:
    69 N*m{ 104 kgf*cm , 51 ft.*lbf }

  1. Connect the 30 terminal with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.

  1. Connect the starter connector.


5. INSTALL STARTER ASSEMBLY (for 2.7 kW Type)
  1. Install the starter with the 2 bolts, nut and stay.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }

  1. Install the starter stay with the 2 bolts and nut.

    Torque:
    Bolt:
    37 N*m{ 380 kgf*cm , 27 ft.*lbf }
    Nut:
    12.5 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Connect the 30 terminal with the nut.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }

  1. Install the terminal cap.

  1. Connect the starter connector.


6. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

  1. C102209
    Install the clutch release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }


7. CONNECT WIRE HARNESS

  1. C112944
    Connect the 2 connectors and clamp.


8. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C102659E01
    Install 2 new clips to the transmission control cable bracket No.1.

  1. Install the transmission control cable assembly to the transmission control cable bracket No.1.

    NOTICE:
    1. Be sure that A claws of the clips are firmly engaged into the bracket grooves.
    2. Be sure the cable is set in the clip with both B claws erected to prevent slippage of the cable in the opposite direction.

  1. C102206E01
    Align the matchmarks on the control cable assembly and the outer lever.

  1. Install the transmission control cable assembly to the outer levers with the 2 nuts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


9. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller shaft assembly in the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. C102185E01
    Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }


10. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase)

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller with center bearing shaft assembly in the extension housing.

  1. C107214
    Install the center support bearing assembly No.1, and temporarily tighten the 2 bolts.

  1. C102185E01
    Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }

  1. C107213E01
    Check that the center line of the bracket is at right angles to the shaft axial direction.

  1. C115777E01
    Adjust the center support bearing assembly No.1.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing No.1 to maintain the angles, as shown.
    2. In the same conditions, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) of each other in the vehicle's longitudinal direction with the vehicle unladen.

  1. Tighten the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }


11. INSTALL EXHAUST PIPE ASSEMBLY FRONT NO.2 (for Long Wheelbase)

  1. A077857
    Inspect the compression spring.

    1. Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5 mm (1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.

  1. A102062E05
    Install the gasket.

    1. Fully insert a new gasket to the exhaust pipe sub-assembly front No.1 by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust pipe sub-assembly front No.1 are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not damage the outer face.
      3. Do not reuse the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe sub-assembly front No.2 to force the gasket onto the exhaust pipe sub-assembly front No.1.

  1. Connect the exhaust pipe support, and install a new gasket and the exhaust pipe sub-assembly front No.2 with the 4 bolts, 2 nuts, and 2 compression springs.

    Torque:
    Exhaust pipe sub-assembly front No.1 side:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Exhaust pipe assembly tail side:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    After installation, check that the clearance is almost same at any point between the flanges of the exhaust pipe sub-assembly front No.2 and exhaust pipe sub-assembly front No.1.


12. INSTALL EXHAUST PIPE ASSEMBLY FRONT NO.2 (for Super Long Wheelbase)

  1. A077857
    Inspect the compression spring.

    1. Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5 mm (1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.

  1. A102062E05
    Install the gasket.

    1. Fully insert a new gasket to the exhaust pipe sub-assembly front No.1 by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust pipe sub-assembly front No.1 are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not damage the gasket.
      3. Do not reuse the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe sub-assembly front No.2 to force the gasket onto the exhaust pipe sub-assembly front No.1.

  1. Connect the exhaust pipe support, and install a new gasket and the exhaust pipe sub-assembly front No.2 with the 4 bolts, 2 nuts, and 2 compression springs.

    Torque:
    Exhaust pipe sub-assembly front No.1 side:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Exhaust pipe assembly center side:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    After installation, check that the clearance is almost same at any point between the flanges of the exhaust pipe sub-assembly front No.2 and exhaust pipe sub-assembly front No.1 .


13. ADD MANUAL TRANSMISSION OIL

  1. D025304E01
    Park the vehicle in a level place.

  1. Remove the transmission filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.

    Oil grade:
    TOYOTA Genuine Manual Transmission Gear oil API GL-3 (GL-4) or equivalent
    Viscosity:
    SAE 75W-90
    Capacity:
    2.2 liters (2.3 US qts, 1.9 Imp. qts)

    NOTICE:
    1. Problems may occur when the oil level is too high or too low.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

15. CHECK FOR EXHAUST GAS LEAKS

16. PERFORM INITIALIZATION
Some systems need initialization after reconnecting the cable to the negative battery terminal (Click here).
← INSTALLATION (Jan 2015 – Mar 2016)INSTALLATION (Jan 2017 – Nov 2017) →