2014-2019 Hiace · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. INSTALL CLUTCH PEDAL SPRING HOLDER

  1. C114261E03
    Apply MP grease to the inside of a new clutch pedal spring holder.
    Text in Illustration 
    V100135
    MP grease

  1. Install the clutch pedal spring holder.


2. INSTALL CLUTCH PEDAL PAD
  1. Install the clutch pedal pad to the clutch pedal sub-assembly.


3. INSTALL CLUTCH PEDAL NO.1 CUSHION

  1. C102633
    Using needle-nose pliers, install the clutch pedal No. 1 cushion to the clutch pedal sub-assembly.


4. INSTALL CLUTCH PEDAL SHAFT COLLAR

  1. C102648E07
    Apply MP grease to the inner, outer and end surfaces of 2 new pedal bushes.
    Text in Illustration 
    *1
    Pedal bush
    *2
    Clutch pedal shaft collar
    V100135
    MP grease

  1. Install the clutch pedal shaft collar and 2 pedal bushes to the clutch pedal sub-assembly.


5. INSTALL CLUTCH PEDAL SUB-ASSEMBLY

  1. C114260E04
    Align the matchmarks on the clutch pedal support sub-assembly.
    Text in Illustration 
    *a
    Matchmarks

  1. Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt, washer and nut.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }

    HINT:
    Hold the nut and tighten the bolt.


6. INSTALL TURN OVER SPRING SEAT COMPRESSION SPRING

  1. C105011E03
    Apply MP grease to the sliding portion of the turnover spring seat compression spring.
    Text in Illustration 
    V100135
    MP grease

  1. Install the turnover spring seat compression spring.


7. INSTALL CLUTCH PEDAL SPRING

  1. C114269E03
    Apply MP grease to the sliding portion of the clutch pedal spring.
    Text in Illustration 
    *a
    Spring end
    V100135
    MP grease

  1. C104825E04
    Install the clutch pedal spring.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

    NOTICE:
    Be sure to install the clutch pedal spring with its end facing upward.

  1. Install a new E-ring.


8. INSTALL CLUTCH SWITCH ASSEMBLY
  1. Using a 14 mm union nut wrench, install the clutch switch assembly.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the clutch switch connector.


9. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

  1. C114263E01
    Align the clip of the clutch pedal support with the hole of the bracket on the vehicle, and install the clutch pedal support sub-assembly.

    NOTICE:
    Make sure that the clip of the clutch pedal support is securely engaged in the hole of the bracket on the vehicle.

  1. C224602
    Install the clutch pedal support sub-assembly with the bolt.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. C102635E02
    Apply MP grease to the sliding portions of the push rod clevis and clutch pedal sub-assembly.
    Text in Illustration 
    V100135
    MP grease

  1. Install the push rod clevis to the cutout of the clutch pedal sub-assembly from the right side of the vehicle and push it downward.

    NOTICE:
    Check that the push rod cannot be turned 30° or more in order to confirm that the clevis is securely engaged to the clutch pedal sub-assembly.

  1. Connect the clutch switch connector and attach the wire harness clamp.


10. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

  1. C105013
    Install the clutch master cylinder with the 2 nuts.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }


11. INSPECT AND ADJUST CLUTCH PEDAL HEIGHT
(Click here)

12. INSTALL NO. 1 AIR DUCT

13. INSTALL WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY (for LHD)
  1. w/ Rear Wiper:
    Connect the 2 connectors and 2 washer hoses.

  1. w/o Rear Wiper:
    Connect the connector and washer hose.

  1. Attach the hose clamp.

  1. Install the windshield washer motor and pump assembly with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the connector to the windshield washer motor and pump assembly.


14. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
  1. Attach the 8 claws to install the instrument panel finish panel lower center.


15. INSTALL SHIFTING HOLE COVER ASSEMBLY
  1. for Manual Transmission:
    Attach the 6 claws to install the shifting hole cover assembly.

  1. for Automatic Transmission:
    Attach the 8 claws to install the shifting hole cover assembly.


16. INSTALL SHIFT LEVER KNOB

17. INSTALL PARKING BRAKE HOLE COVER
  1. Attach the 6 claws to install the parking brake hole cover.


18. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Attach the 3 claws to instrument panel under cover sub-assembly No. 1.

  1. Install the the 2 clips.


19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL
  1. Connect the fuel lid lock control cable and bonnet (hood) control cable assembly to the instrument panel finish lower.

  1. Attach the 4 clips to install the instrument panel finish panel lower.

  1. Install the 2 clips.


20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 47 in.*lbf }


21. PERFORM INITIALIZATION
Some systems need initialization when disconnecting the cable from the negative battery terminal. (Click here)
← INSTALLATION (Oct 2014 – Mar 2016)INSTALLATION (from Jan 2017) →