2014-2019 Hiace · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built from Oct 2014


1. INSTALL REAR DIFFERENTIAL CARRIER GASKET
  1. Install a new differential carrier gasket to the rear axle housing assembly.


2. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
  1. Clean the contact surfaces of the differential carrier assembly and the rear axle housing assembly.

  1. C030284E01
    Install the differential carrier assembly with the 10 nuts and washers.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


3. INSTALL LOAD SENSING BRACKET

  1. C102254
    Install the load sensing bracket with the 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


4. INSTALL REAR AXLE HOUSING DRAIN PLUG
  1. Install the drain plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


5. INSTALL PROPELLER SHAFT ASSEMBLY (for Super Long Wheelbase)

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller with center bearing shaft assembly in the extension housing.

  1. C107214
    Install the center support bearing assembly No.1, and temporarily tighten the 2 bolts.

  1. C102185E01
    Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }

  1. C107213E01
    Check that the center line of the bracket is at right angles to the shaft axial direction.

  1. C115777E01
    Adjust the center support bearing assembly No.1.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing No.1 to maintain the angles, as shown.
    2. In the same conditions, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) of each other in the vehicle's longitudinal direction with the vehicle unladen.

  1. Tighten the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }


6. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller shaft assembly in the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. C102185E01
    Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }


7. INSTALL REAR AXLE SHAFT LH OIL SEAL (w/ ABS)

  1. A239133E01
    Using SST and a hammer, install a new rear axle shaft oil seal.
    SST
    09554-22010  

    Seal installation depth:
    34.5 to 35.5 mm (1.358 to 1.398 in.)

    NOTICE:
    1. Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
    2. Do not tilt the oil seal during installation.

    Text in Illustration 
    *1
    Rear Axle Housing Assembly
    *2
    Rear Axle Shaft Oil Seal
    *a
    Seal installation depth

  1. Apply MP grease to the oil seal lip.


8. INSTALL REAR AXLE SHAFT LH OIL SEAL (w/o ABS)

  1. A239134E01
    Using SST and a hammer, install a new rear axle shaft oil seal.
    SST
    09554-22010  

    Seal installation depth:
    0.5 to 1.5 mm (0.0197 to 0.0590 in.)

    NOTICE:
    1. Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
    2. Do not tilt the oil seal during installation.

    Text in Illustration 
    *1
    Rear Axle Housing Assembly
    *2
    Rear Axle Shaft Oil Seal
    *a
    Seal installation depth

  1. Apply MP grease to the oil seal lip.


9. INSTALL REAR AXLE SHAFT RH OIL SEAL (w/ ABS)

HINT:
Installation procedure of the RH side is the same as that of the LH side.


10. REMOVE REAR AXLE SHAFT RH OIL SEAL (w/o ABS)

HINT:
Installation procedure of the RH side is the same as that of the LH side.


11. INSTALL BEARING RETAINER O-RINGS
  1. Apply MP grease to the bearing retainer O-ring.

  1. Install the bearing retainer O-ring to the rear axle shaft housing.


12. INSTALL REAR AXLE SHAFT WITH BACKING PLATE LH

  1. C102664J01
    Install the rear axle shaft with backing plate to the rear axle shaft housing with the 4 nuts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the rear axle shaft oil seal.
    2. Be careful not to damage the skid control rotor rear.


13. REMOVE REAR AXLE SHAFT WITH BACKING PLATE RH

HINT:
Installation procedure of the RH side is the same as that of the LH side.


14. INSTALL REAR SPEED SENSOR LH (w/ ABS)

  1. Install the rear speed sensor LH with the bolt.

    C281302

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Prevent foreign matter from attaching to the sensor tip.

  1. Attach the 4 clamps.

  1. Connect the connector.


15. INSTALL SPEED SENSOR REAR RH (w/ ABS)

HINT:
Installation procedure of the RH side is the same as that of the LH side.


16. INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY LH

  1. C102608
    Install the wheel brake cylinder assembly with the 2 bolts.

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }

  1. Using a union nut wrench, connect the brake tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


17. INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY RH

HINT:
Installation procedure of the RH side is the same as that of the LH side.


18. APPLY HIGH TEMPERATURE GREASE

  1. C102609E02
    Apply high temperature grease to the shoe attached surface of the backing plate.
    Text in Illustration 
    *1
    High temperature grease


19. CONNECT PARKING BRAKE CABLE ASSEMBLY NO. 3
  1. Install the parking brake cable assembly No.3 to the parking brake equalizer.

  1. Install the parking brake cable assembly No.3 with the 5 bolts and the nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }


    C102158

  1. C102159
    Install the parking brake cable assembly No.3 to the backing plate with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


20. CONNECT PARKING BRAKE CABLE ASSEMBLY NO. 2

HINT:
Installation procedure of the RH side is the same as that of the LH side.


21. INSTALL PARKING BRAKE SHOE STRUT SET LH

  1. F042695E03
    Apply the high temperature grease to the adjusting bolt.
    Text in Illustration 
    *1
    High temperature grease

  1. Install the tension spring to the shoe strut set.


22. INSTALL PARKING BRAKE SHOE STRUT SET RH

HINT:
Installation procedure of the RH side is the same as that of the LH side.


23. INSTALL REAR BRAKE SHOES

  1. for 254 mm drum:

    1. C102607E02
      Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Brake Shoe Lever
      *2
      Brake Shoe Strut Set
      *3
      Rear Brake Shoe
      *4
      Rear Cushion Lever
      *5
      C-washer

    2. C102606
      Connect the parking brake cable No. 3 to the front brake shoe.

    3. C102603E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

  1. for 295 mm drum:

    1. C263530E01
      Install the rear brake shoe, brake shoe strut set and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Rear Brake Shoe
      *2
      Brake Shoe Strut Set
      *3
      Brake Shoe Lever
      *4
      Automatic Adjust Lever
      *5
      C-washer
      *6
      E-ring

    2. Install a new E-ring and the automatic adjust lever.

    3. C263529
      Connect the parking brake cable No. 3 to the front brake shoe.

    4. C263525
      Install the tension spring as shown in the illustration.

    5. C263528E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  


24. INSTALL FRONT BRAKE SHOES

  1. for 254 mm drum:

    1. Install the return spring to each brake shoe.

    2. C102604E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    3. C264855E02
      Install the brake shoe lower strut.
      Text in Illustration 
      *A
      LH Side
      *B
      RH Side

      NOTICE:
      Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.

    4. C102600
      Using needle-nose pliers, install the tension spring.

  1. for 295 mm drum:

    1. C263527E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    2. Install the return spring to each brake shoe.


25. CONNECT PARKING BRAKE SHOE STRUT SET LH

  1. for 254 mm drum:

    1. C231698E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  

  1. for 295 mm drum:

    1. C263526E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  


26. CONNECT PARKING BRAKE SHOE STRUT SET RH

HINT:
Installation procedure of the RH side is the same as that of the LH side.


27. INSTALL AUTOMATIC ADJUST LEVER LH

  1. for 254 mm drum:

    1. C102605
      Install the automatic adjust lever and tension spring.

      NOTICE:
      Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.


28. INSTALL AUTOMATIC ADJUST LEVER RH

HINT:
Installation procedure of the RH side is the same as that of the LH side.


29. INSPECT REAR DRUM BRAKE

  1. Check the each part is installed properly.

    C264221E02

    C263532E01

    Text in Illustration 
    *A
    for 254 mm Drum
    *B
    for 295 mm Drum
    *C
    LH Side
    *D
    RH Side
    *a
    Front
    -
    -

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.

  1. If they are not installed correctly, reinstall them as shown in the illustration.


30. INSTALL REAR AXLE BRAKE DRUM GASKETS
  1. Install the new brake drum gasket to the rear axle shaft.


31. INSTALL REAR BRAKE DRUM SUB-ASSEMBLIES

32. ADJUST REAR DRUM BRAKE SHOE CLEARANCE

  1. Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.

    C263542E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.

    C263541E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Install the hole plug.


33. ADD BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT3 or equivalent


34. BLEED BRAKE LINE
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.

  1. At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.

  1. Repeat this procedure until the air in the brake fluid is completely bled out.

  1. Tighten the bleeder plug.

    1. Front bleeder plug:

      Torque:
      10.8 N*m{ 110 kgf*cm , 8 ft.*lbf }

    2. Rear bleeder plug:

      Torque:
      11.0 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


35. INSPECT BRAKE FLUID LEVEL
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No.116 DOT3 or equivalent


36. FILL DIFFERENTIAL OIL
  1. Remove the differential filler plug and gasket.

  1. Fill with oil.

    Oil grade:
    Toyota Genuine Differential Gear oil GL-5 or equivalent

    Recommended oil viscosity 
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W or 80W-90
    Standard differential oil capacity 
    Body Type
    Specified Condition
    Standard Body
    3.10 liters (3.28 US qts, 2.73 Imp. qts)
    Wide Body
    3.25 liters (3.43 US qts, 2.86 Imp. qts)

  1. Check the oil level.

  1. Install the differential filler plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    After replacing the oil, recheck the oil level after driving.


37. INSPECT AND ADJUST DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. D025304E04
    Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause trouble.
    2. After replacing oil, drive the vehicle and check the oil level.

    HINT:
    If necessary, fill the rear differential carrier with hypoid gear oil.

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


38. INSTALL REAR WHEELS

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }


39. INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Pull firmly on the parking brake control handle.

  1. Release the parking brake lock, and return the parking brake control handle to its off position.

  1. Slowly pull the parking brake control handle all the way up, and count the number of clicks.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

    HINT:
    1. If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
    2. If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.


40. ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Lift the vehicle

  1. C102142E01
    Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.

  1. Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

  1. Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake control handle, check that the parking brake indicator light comes on.

    Standard:
    Brake warning light always comes on at the first click.

  1. Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. Lower the vehicle.


41. ABS SPEED SENSOR SIGNAL
(Click here)
← REASSEMBLY (from Jan 2017)PROBLEM SYMPTOMS TABLE (Oct 2014 – Dec 2014) →