2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

2. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
  1. Perform the same procedure as above on the opposite side. (Click here)


3. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
  1. Perform the same procedure as above on the opposite side. (Click here)


4. REMOVE FRONT DOOR SCUFF PLATE RH

5. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the 5 bolts and engine service hole sub cover.


6. REMOVE FAN & GENERATOR V BELT

  1. A102135E01
    Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and decrease the tension in the drive belt. Then remove the drive belt.

    NOTICE:
    When removing the drive belt, do not use the idle pulley's bolt.

    HINT:
    After removing the drive belt, move the tensioner upward to the maximum amount.


7. REMOVE AIR PRESSURE SENSOR (w/ Manifold Absolute Pressure Sensor)

  1. A259661
    Disconnect the connector.

  1. Disconnect the vacuum hose and clamp.

  1. Detach the wire harness clamp

  1. Remove the 2 bolts and air pressure sensor together with the bracket.

  1. A259662
    Remove the bolt and air pressure sensor.


8. REMOVE INTAKE AIR CONNECTOR

  1. A102437E01
    Slide the clamp and disconnect the No. 2 ventilation hose and vacuum hose. (A)

  1. Loosen the 2 hose clamp bolts. (B)

  1. Remove the 2 bolts and intake air connector. (C)


9. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the bolts and ignition coil assembly.


10. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Disconnect the ventilation hose No.1.

  1. A101928
    Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.

  1. Remove the cylinder head cover gasket and cylinder head cover gasket No.2 from the cylinder head cover.


11. REMOVE TIMING CHAIN GUIDE

  1. G037278
    Remove the 2 bolts, timing chain guide and O-ring.


12. REMOVE CAMSHAFT TIMING GEAR OR SPROCKET

  1. Set No.1 cylinder to TDC/compression.

    1. A097861E05
      Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

    2. Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of bearing cap No.1, as shown in the illustration.

      HINT:
      If not, turn the crankshaft pulley 1 revolution (360°) and align the marks as above.

  1. A097862E04
    Put paint marks on the timing chain and camshaft timing gear/sprocket.

  1. A097863E01
    Fix the camshaft with a wrench and then loosen the sprocket bolt.

    NOTICE:
    Be careful not to damage the oil delivery pipe.

  1. A086539
    Using a 10 mm socket hexagon wrench, remove the timing chain cover plug.

  1. A097864E02
    Using a screwdriver, access the tensioner stopper plate through the chain tensioner service hole. Move the stopper plate upward to release the lock. Then hold the plate in that position as shown in the illustration.

    HINT:
    If the stopper plate's lock is difficult to release, slightly rotate the camshaft's hexagon-shaped part to the left and right.

  1. A097865E01
    With the stopper plate's lock released, slightly rotate the camshaft to the right. Then maintain it in that position.

    NOTICE:
    Be careful not to damage the oil delivery pipe.

    HINT:
    Rotating the camshaft to the right will cause pressure to be applied to the tensioner plunger.

  1. A086542E02
    Remove the screwdriver from the chain tensioner service hole. Move the stopper plate to the position shown in the illustration. Then insert a hexagon wrench into the hole.

    HINT:
    1. If the wrench cannot fit into the hole, slightly rotate the camshaft to the left and then to the right. Then insert the wrench.
    2. To prevent the wrench from falling out, use tape to fix the wrench in place.

  1. Remove the camshaft timing sprocket from the camshaft.


13. REMOVE CAMSHAFT BEARING CAP

  1. A086543
    Uniformly loosen the 21 bearing cap bolts in several steps in the sequence shown in the illustration.

  1. Remove the 9 bearing caps, oil delivery pipe, O-ring and camshaft.

    NOTICE:
    1. Place the camshaft on a flat surface and loosen the bolts uniformly.
    2. Do not pry the camshaft with a tool by applying excessive force to it.
    3. Do not damage the reception part of the camshaft on the cylinder head side.


14. REMOVE NO.2 CAMSHAFT

15. REMOVE CAMSHAFT

  1. A086544
    Remove the camshaft while holding the timing chain.

  1. A086545
    Tie the timing chain with a string as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.


16. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

  1. Check the lock of the camshaft timing gear.

    1. A346182E01
      Using SST, grip the hexagonal portion, and then secure the SST and camshaft in a vise as shown in the illustration and check that the camshaft timing gear assembly does not rotate.
      SST
      09212-31010  
      Text in Illustration 
      *a
      Hexagonal Portion

      NOTICE:
      1. Do not damage the camshaft.
      2. Never grip areas other than the hexagonal portion, as this may cause damage.

  1. A086546E02
    Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      2 advance side paths are provided in the groove of the camshaft. Plug one of the paths with a rubber piece.

    2. A086547E02
      Break through the tape of the advance side path and the retard side path on the opposite side to the hole of the advance side path.

    3. Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the two broken paths.

      NOTICE:
      Some oil splashing will occur. Cover the paths with a shop rag or a piece of cloth.

    4. A086548E01
      Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.

      OK:
      Gear rotates in the advance direction.

      HINT:
      This operation releases the lock pin for the most retarded position.

    5. When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path, in that order.

      NOTICE:
      Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Rotate the camshaft timing gear within its movable range several times, but do not turn it to the most retarded position. Check that the gear rotates smoothly.

      OK:
      Gear rotates in the advance direction.

      NOTICE:
      Do not use air pressure to perform the smooth operation check.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing gear is locked at the most retarded position.


17. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

  1. A344523E01
    Using SST, grip the hexagonal portion, and then secure the SST and camshaft in a vise as shown in the illustration.
    SST
    09212-31010  
    Text in Illustration 
    *a
    Hexagonal Portion

    NOTICE:
    1. Do not damage the camshaft.
    2. Never grip areas other than the hexagonal portion, as this may cause damage.

  1. A097871E01
    Remove the flange bolt and camshaft timing gear.

    NOTICE:
    1. Be sure not to remove the other 3 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →