2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Jan 2015 – Dec 2016 from Jan 2017


1. INSTALL REAR CRANKSHAFT OIL SEAL
  1. Apply MP grease to a new rear crankshaft oil seal lip.

    NOTICE:
    Keep the lip free from foreign matter.

  1. A102145E02
    Using SST and a hammer, tap in the rear crankshaft oil seal until its surface is flush with the rear oil seal retainer edge.
    SST
    09223-15030  
    09950-70010   (09951-07150)

    NOTICE:
    Wipe off extra grease from the crankshaft.


2. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

HINT:
If any one of the mounting bolts is broken or deformed, replace it.

  1. A004869E08
    Apply adhesive to 2 or 3 threads of the mounting bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    Text in Illustration 
    *a
    Adhesive

  1. A102138E01
    Fix the crankshaft with SST.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Temporarily install the flywheel with 10 new mounting bolts.

  1. A109815E02
    Install and uniformly tighten the 10 mounting bolts in several steps in the sequence shown in the illustration.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }

    If any one of the mounting bolts does not meet the torque specification, replace the mounting bolt.

  1. Mark the top of the bolts with paint.

  1. Tighten the 10 bolts 90° in the same sequence.

  1. Check that the paint marks are now at a 90° angle to the top.


3. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

  1. G038107E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A314019E01
    Install the front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.
    Text in Illustration 
    *1
    Front Drive Plate Spacer (Reversible)
    *2
    Drive Plate and Ring Gear Sub-assembly
    *3
    Rear Drive Plate Spacer
    V100135
    Transmission Side
    V100136
    Engine Side

    HINT:
    1. The front drive plate spacer is reversible.
    2. As the rear drive plate spacer and drive plate and ring gear sub-assembly are not reversible, be sure to install it so that it is facing in the direction shown in the illustration.

  1. Clean the bolts and bolt holes.

  1. Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A222355E01
    Install and uniformly tighten the 10 bolts in several steps in the sequence shown in the illustration.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not start the engine for at least an hour after installing the drive plate and ring gear sub-assembly.


4. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

  1. C104158E01
    Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.
    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc assembly in the wrong direction.


5. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C114265E02
    Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.

  1. Following the procedures shown in the illustration, tighten the 6 bolts starting from the bolt located near the knock pin on the top.

    SST
    09301-00110  

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Evenly tighten the bolts by following the order shown in the illustration.
    2. Tighten the bolts after checking that the disc is in the center by lightly moving the SST up and down, left and right.


6. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C086210
    Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    0.9 mm (0.035 in.)

  1. C114266E01
    If alignment is not as specified, adjust the diaphragm spring tip alignment using SST.
    SST
    09333-00013  


7. INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)

8. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)
← INSTALLATION (Jan 2015 – Dec 2016)COMPONENTS (from Oct 2014) →