2014-2019 Hiace · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. INSTALL SLIDE DOOR ROLLER ASSEMBLY LOWER
  1. Install the slide door roller assembly lower with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


2. INSTALL SLIDE DOOR HINGE ASSEMBLY CENTER
  1. Install the slide door roller hinge assembly center with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


3. INSTALL SLIDE DOOR ROLLER ASSEMBLY UPPER
  1. Install the slide door roller assembly upper with the 2 bolts

    Torque:
    11.5 N*m{ 117 kgf*cm , 9 ft.*lbf }


4. INSTALL SLIDE DOOR SUB-ASSEMBLY

5. INSTALL SLIDE DOOR LOWER RAIL PLATE

  1. B106870
    Install the slide door lower rail plate with the bolt.


6. INSTALL SLIDE DOOR UPPER RAIL CUSHION

  1. B106867
    Install the slide door upper rail cushion with the bolt.


7. INSTALL SLIDE RAIL END MOULDING
  1. Engage the clip and install the slide rail end moulding.


8. INSTALL REAR DOOR SCUFF PLATE

  1. B111430
    Engage the 11 clips, and install the rear door scuff plate.


9. INSTALL SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY

  1. B101184
    Install the slide door lock remote control assembly with the 5 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


10. INSTALL POWER SLIDE DOOR LOCK ASSEMBLY (w/ Auto Closer)

  1. B111441E01
    Using a "torx" socket wrench, install the 3 "torx" screws.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the bolt.

  1. Engage the wire harness and connect the cable.


11. INSTALL REAR DOOR LOCK ASSEMBLY (w/o Auto Closer)

  1. B111440E01
    Using a "torx" socket wrench, install the 3 "torx" screws.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Engage the wire harness and connect the cable.


12. INSTALL SLIDE DOOR CLOSER RELAY (w/ Auto Closer)

  1. B101181
    Install the slide door closer relay with the bolt.

  1. Connect the connector.


13. INSTALL SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY

  1. B111439E01
    Install the slide door full open stop lock assembly with the 2 bolts.

  1. Install the clamp.


14. INSTALL SLIDE DOOR DOWN FEMALE STOP

  1. B101179
    Install the slide door down female stop with the 2 bolts.


15. INSTALL SLIDE DOOR CONTROL JUNCTION FEMALE

  1. B101178E01
    Install the slide door control junction female with the 2 bolts.

  1. Connect the connector.


16. INSTALL SLIDE DOOR LOCK ASSEMBLY FRONT

  1. B111438E01
    Install the slide door lock assembly front with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Clamp the cable and install the end of the cable to the slide door lock remote control assembly front.


17. INSTALL REAR DOOR LOCK CHILD PROTECTION COVER (w/ Cover)

  1. for Cover Type:

    1. B152381
      Install the rear door lock child protection cover with the clip.

  1. for Tape Type:

    HINT:
    When installing the front door weatherstrip, heat the vehicle body using a heat light.

    NOTICE:
    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the vehicle body.

      Heating Temperature:
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

    4. B264315
      Install a new rear door lock child protection cover.


18. INSTALL REAR DOOR OPEN CONTROL LINK ASSEMBLY (w/o Cover)
  1. Install the rear door open control link assembly with the clip.


19. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

  1. B101175
    Install the rear door outside handle assembly with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the link.

  1. B102797
    Install the slide door lock cylinder assembly with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the link.


20. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
  1. Install the rear door inside handle sub-assembly with the 2 bolts.

  1. Connect the link.


21. INSTALL SLIDE DOOR SERVICE HOLE NO.1 COVER

22. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY (w/ Auto Closer)

  1. B101171E01
    Engage the 19 clips and claw, and install the rear door trim board sub-assembly.

  1. B101169
    Using a "torx" socket wrench, install the 2 "torx" screws.


23. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY (w/o Auto Closer)

  1. B101170
    Install the rear door trim board sub-assembly with the 20 clips.


24. INSTALL SLIDE DOOR WINDOW GARNISH (w/ Auto Closer)

  1. B101167E01
    Engage the clips and install the slide door window garnish.


25. INSTALL DOOR LOCK CONTROL KNOB BEZEL (w/o Auto Closer)

  1. B101168E01
    Engage the claws and install the door lock control knob bezel.

  1. Using a "torx" socket wrench, install the 2 "torx" screws.


26. INSPECT AND ADJUST SLIDE DOOR
(Click here)
← ADJUSTMENT (from Oct 2014)COMPONENTS (from Oct 2014) →