2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. REMOVE BATTERY SERVICE HOLE COVER (w/ Sub-Battery)

2. DISCONNECT BATTERY NEGATIVE CABLE

3. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    A316611E01

    Text in Illustration 
    *1
    Bleeder Plug
    *2
    Radiator Reservoir Cap Sub-assembly
    *3
    Radiator Reservoir Assembly
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block drain cock plug (on the engine oil cooler cover), and drain the engine coolant.

  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plug (on the engine oil cooler cover).

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


5. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)

  1. B107528
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


6. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)

  1. B107542
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


7. REMOVE FRONT DOOR SCUFF PLATE RH

8. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the engine service hole sub cover assembly.


9. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A102278
    Remove the 2 bolts. Separate the vane pump oil reservoir assembly.


10. DISCONNECT OIL RETURN HOSE (w/ Inter Cooler)

  1. A106042
    Loosen the clip.

  1. Disconnect the oil return hose from the intake manifold.


11. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)

  1. A106043
    Disconnect the fuel pressure sensor connector.

  1. A106844
    Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.


12. REMOVE AIR HOSE NO.4

  1. A102281
    Loosen the 2 clamps.

  1. Remove the air hose No.4.


13. REMOVE ENGINE THROTTLE BODY ASSEMBLY

  1. A102282
    Disconnect the 2 throttle body connectors.

  1. A102902
    Remove the 2 bolts, 2 nuts, and the diesel throttle body assembly.

  1. Remove the gasket from intake air connector.


14. REMOVE ENGINE SERVICE HOLE COVER NO.2

  1. A113043
    Roll up the carpet.

  1. Remove the 3 bolts and the engine service hole cover No.2.


15. REMOVE INTAKE AIR CONNECTOR (w/o EGR Valve)

  1. A106846
    Remove the bolt, and separate the manifold stay.

  1. Disconnect the vacuum hose from intake air connector.

  1. A106848E01
    Remove the bolt, 2 nuts and the intake air connector assembly.

  1. Remove the 2 gaskets and intake air connector No.2 from the intake air connector.


16. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve)

  1. Remove the vacuum regulating valve.

    1. A103046
      Remove the 2 vacuum hoses and the vacuum regulating valve connector.

    2. Remove the 2 bolts and the vacuum regulating valve.

  1. Remove the EGR valve assembly with the sensor.

    1. A115757
      Remove the bolt, and separate the manifold stay.

    2. Disconnect the vacuum hose from the intake air connector.

    3. A103043
      Disconnect the intake air temperature sensor connector.

    4. Disconnect the EGR valve position sensor connector.

    5. A115761E01
      Remove the bolt, 2 nuts and the intake air connector assembly.

    6. Remove the 2 gaskets and EGR valve assembly from the intake air connector.


17. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the oil level gauge.

  1. Remove the bolt and oil level gauge guide.


18. REMOVE INJECTION PIPE
SST
09023-12701  

  1. Remove the injection pipe.

    1. A103526
      Remove the 2 nuts and injection pipe clamp No.3.

    2. A103532
      Using SST, remove the 4 injection pipes.
      SST
      09023-12701  


19. REMOVE FUEL INLET PIPE SUB-ASSEMBLY
  1. Using SST, remove the fuel inlet pipe sub-assembly.

    SST
    09023-12701  


20. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY NO.2

  1. A103529
    Disconnect 3 fuel hoses from nozzle leakage pipe assembly No.2.

  1. A103528
    Remove the union bolt from nozzle leakage pipe No.2.

  1. A103527
    Remove the 2 bolts and nozzle leakage pipe No.2.

  1. Remove the gasket from nozzle leakage pipe No.2.


21. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the fuel pressure sensor connector from the common rail assembly.

  1. Disconnect the fuel hose from the fuel pressure limiter.

  1. A102476E01
    Remove the 2 bolts and common rail assembly.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →