2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. REMOVE BATTERY SERVICE HOLE COVER (w/ Sub-Battery)

2. DISCONNECT BATTERY NEGATIVE CABLE

3. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)

  1. B107528
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


4. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)

  1. B107542
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


5. REMOVE FRONT DOOR SCUFF PLATE RH

6. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the engine service hole sub cover assembly.


7. REMOVE FAN & GENERATOR V BELT

  1. A102808E03
    Remove the drive belt by rotating the tensioner pulley in clockwise direction to loosen its tension with the pulley set bolt of the tensioner.


8. SET NO.1 CYLINDER TO TDC/ COMPRESSION

  1. A072847E01
    Align the matchmarks of the crankshaft pulley and timing gear case cover by rotating the crankshaft in clockwise direction.

    HINT:
    Make sure that both camnoses on the intake side and exhaust side of the cylinder No.1 face upward.


9. REMOVE TIMING BELT COVER NO.1
  1. Remove the wire harness clamp.

  1. A102815
    Remove the 6 bolts and timing belt cover No.1.


10. REMOVE TIMING BELT

  1. A070549E01
    Turn the crankshaft in the clockwise direction and align the timing marks as shown in the illustration.

  1. A070550
    Uniformly loosen the 2 bolts, and remove the chain tensioner assembly No.1.

  1. Remove the timing belt.


11. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A102278
    Remove the 2 bolts. Separate the vane pump oil reservoir assembly.


12. DISCONNECT OIL RETURN HOSE (w/ Inter Cooler)

  1. A106042
    Loosen the clip.

  1. Disconnect the oil return hose from the intake manifold.


13. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)

  1. A106043
    Disconnect the fuel pressure sensor connector.

  1. A106844
    Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.


14. REMOVE AIR HOSE NO.4

  1. A102281
    Loosen the 2 clamps.

  1. Remove the air hose No.4.


15. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  1. A102282
    Disconnect the 2 throttle body connectors.

  1. A102902
    Remove the 2 bolts, 2 nuts, and the diesel throttle body assembly.

  1. Remove the gasket from intake air connector.


16. REMOVE ENGINE SERVICE HOLE COVER NO.2

  1. A113043
    Roll up the carpet.

  1. Remove the 3 bolts and the engine service hole cover No.2.


17. REMOVE INTAKE AIR CONNECTOR (w/o EGR Valve)

  1. A106846
    Remove the bolt, and separate the manifold stay.

  1. Disconnect the vacuum hose from intake air connector.

  1. A106848E01
    Remove the bolt, 2 nuts and the intake air connector assembly.

  1. Remove the 2 gaskets and intake air connector No.2 from the intake air connector.


18. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve)

  1. Remove the vacuum regulating valve.

    1. A103046
      Remove the 2 vacuum hoses and the vacuum regulating valve connector.

    2. Remove the 2 bolts and the vacuum regulating valve.

  1. Remove the EGR valve assembly with the sensor.

    1. A115757
      Remove the bolt, and separate the manifold stay.

    2. Disconnect the vacuum hose from the intake air connector.

    3. A103043
      Disconnect the intake air temperature sensor connector.

    4. Disconnect the EGR valve position sensor connector.

    5. A115761E01
      Remove the bolt, 2 nuts and the intake air connector assembly.

    6. Remove the 2 gaskets and EGR valve assembly from the intake air connector.


19. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the oil level gauge.

  1. Remove the bolt and oil level gauge guide.


20. REMOVE INJECTION PIPE
SST
09023-12701  

  1. Remove the injection pipe.

    1. A103526
      Remove the 2 nuts and injection pipe clamp No.3.

    2. A103532
      Using SST, remove the 4 injection pipes.
      SST
      09023-12701  


21. REMOVE FUEL INLET PIPE SUB-ASSEMBLY
  1. Using SST, remove the fuel inlet pipe sub-assembly.

    SST
    09023-12701  


22. REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY

  1. A070710
    Remove the 4 bolts.

  1. Remove the camshaft timing pulley flange No.2 and pump drive shaft pulley.

  1. A077989
    Using SST, remove the supply pump gear set nut and O-ring while holding the crankshaft pulley.
    SST
    09213-58013  
    09330-00021  

  1. A076978
    Disconnect the 2 fuel hoses.

  1. Disconnect the 2 connectors and wire harness.

  1. Loosen the 2 nuts as shown in the illustration.

  1. A077990E01
    Using SST, disengage the supply pump from the supply pump gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

  1. Remove the 2 nuts and supply pump from the engine.

  1. Remove the O-ring from the supply pump.

  1. Remove the pulley key from the supply pump.


23. REMOVE FUEL TEMPERATURE SENSOR
  1. Mount the injection or supply pump assembly in a soft jaw vise.

  1. A078244E01
    Using a SST, remove the fuel temperature sensor.
    SST
    09922-10010  

  1. Remove the O-ring form the fuel temperature sensor.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →